Gebruiksaanwijzing /service van het product C170 van de fabrikant IBM
Ga naar pagina of 25
C170 User’s Guide Color Monitor English.
ii i First Edition ( August / 200 4 ) Note : For important information, refer to the Monitor Safety and Warranty manual that comes with this monitor..
ENGLISH 1 Safety (Read first) .......................................................................................................2 Setting up the monitor .............................................................................................
2 í í í.
ENGLISH 3 Setting up the monitor Product Description This monitor requires a computer with a suitable on-board sub-system or Video Adapter card that can support SXGA 1280 x 1024, XGA 1024 x 768, SVGA 800 x 600, or VGA 640 x 480 at 60Hz.
4 Be sure to turn off the power before you perform any maintenance on the monitor. Clean your monitor as follows: • Gently wipe the covers and the screen with a soft cloth. Do not use solvents or abrasives. • Remove finger marks and grease with a damp cloth and mild detergent.
5 ENGLISH Connecting your Monitor Be sure to read the ‘Safety’ Information located in the Monitor Safety and Warranty Information Manual before carrying out this procedure. • Before setting up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices.
6 1. Switch on your computer. 2. Switch on your monitor by pushing and releasing the power switch marked [ ] at the front of the bezel. [To switch off your monitor, push and release the power switch again.] 3. To update or install device drivers, follow the instructions in the Device Driver Installation section on page 7.
ENGLISH 7 To install the device driver in Microsoft ® Windows ® 95 or Windows 98, do the following: Note: You must download files from the User’s Guide and Installation Files CD to use the Plug and Play feature in Windows 95 or Windows 98. 1. Turn off the computer and all attached devices.
8 To install the device driver in Microsoft Windows 2000 Professional or Microsoft Windows Millennium Edition (Me), do the following: Note: You must download files from the User’s Guide and Installation Files CD to use the Plug and Play feature in Windows 2000 or Windows Me.
ENGLISH 9 To install the device driver in Windows XP, do the following: Note: You must download files from the User’s Guide and Installation Files CD to use the Plug and Play feature in Windows XP. 1. Turn off the computer and all attached devices. 2.
10 Adjusting Y our Monitor User controls USER CONTROL FEATURES i The image is already optimized for many display modes, however the user controls can be used to adjust the image to your liking. i The settings are saved after adjustment and when exiting the OSD and will be effective thereafter.
ENGLISH 11 The settings adjustable with the user controls are viewed through the On - Screen Display (OSD). Press the enter button [ ] to display the main OSD menu. Initial appearance of OSD On-screen display (OSD) controls i The LCD monitor needs time to become thermally stable the first time you turn it on each day.
12 OSD Icon Description Sub-menu(s) Controls and Adjustments Horizontal Position Vertical Position Horizontal Size Vertical Size Moves the screen left and right . Moves the screen up and down. Adjusts image width Adjusts image height Rotation Trapezoid To correct geometric distortion.
ENGLISH 13 OSD Icon Description Sub-menu(s) Controls and Adjustments Select from standard white colors. Increases or decreases redness Increases or decreases greenness Increases or decreases blueness .
14 OSD Icon Description Sub-menu(s) • Horizontal • Vertical • Save Controls and Adjustments Changes the position of the OSD on the screen. Menu Position • YES • NO Reset should return all available functions (apart from language which should not change unless adjusted via the LANGUAGE menu) to their factory presets.
ENGLISH 15 The display mode the monitor uses is controlled by the computer. Therefore, refer to your computer documentation for details on how to change display modes. If possible, configure your computer for 1024 x 768 addressability at 85Hz vertical refresh rate.
16 To benefit from power management, the monitor must be used in conjunction with a computer that implements the Video Electronics Standards Association (VESA) Display Power Management Signaling (DPMS) Standard.
ENGLISH 17 T roubleshooting If you have a problem setting up or using your monitor, you may be able to solve it yourself. Before calling your retailer or IBM, try the suggested actions that are appropriate to your problem. Problem No power to monitor.
18 Problem Possible Cause Suggested Action Reference The color setting may be incorrect. CHECK SIGNAL CABLE message is shown and power indicator is steady green. Image appears to be discolored User Controls section on page 10. • Adjust the Color settings.
ENGLISH 19 If you are unable to correct the problem yourself, you may seek further help as follows: Call the IBM Support Center In the US call 1-800-426-7378 In Canada(Toronto Only) call 416-383-3344 In Canada(all other) call 1-800-565-3344 In other countries contact your dealer, retailer, or other IBM authorized Servicer.
20 This color monitor (Type-model 6737-X6X) uses a 17-inch FLAT CDT. i Power consumption figures are for the monitor and the power supply combined. Weight Diemension 16 kg (35.27 lbs) 16-inch (406.4 mm) 0.25 mm 100 - 240V ac 50/60Hz 2.0A < 70 W < 5 W Separate, RGB Analog, 0.
ENGLISH 21 C170 FRU Monitor C170 FRU Monitor C170 FRU Monitor C170 FRU Monitor C170 FRU Monitor C170 FRU Monitor C170 FRU-Tilt/Swivel C170 FRU-Tilt/Swivel US,CAN,EMEA US,CAN,EMEA LA, ASEAN LA, ASEAN A.
22 Notices and T rademarks This section contains information on notices and trademarks. Notices IBM may not offer the products, services, or feature discussed in this document in all countries. Consult your local IBM representative for information on the products and services currently available in your area.
ENGLISH 23 Trademarks The following terms, used in this publication, are trademarks or service marks of the IBM Corporation in the United States, other countries, or both; HelpCenter IBM E NERGY S TAR and the E NERGY S TAR logo are U.S Govt. registered trademarks.
Een belangrijk punt na aankoop van elk apparaat IBM C170 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen IBM C170 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens IBM C170 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding IBM C170 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over IBM C170 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van IBM C170 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de IBM C170 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met IBM C170 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
