Gebruiksaanwijzing /service van het product SBC-659P van de fabrikant IBM
Ga naar pagina of 100
SBC-659P Half- size Intel FC-370 Pentium III CPU Card with Intel 815E chipset, Dual LAN, Audio, Dual COMs, LCD & 4 USB..
Copyright Notice This document is copyrighted, 2001. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
Acknowledgments All other product names or trademarks are properties of their respective owners. AMD is a trademark of Advanced Micro Devices, Inc. AMI is a trademark of American Megatrends, Inc. A ward is a trademark of A ward Software International, Inc.
A Message to the Customer AAEON Customer Services Each and every AAEON product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments.
Product Warranty AAEON warrants to you, the original purchaser , that each of its products will be free from defects in materials and workmanship for two years from the date of shipment.
• 1 floppy disk drive interface cable (34-pin, pitch 2.0mm) • 1 IDE hard disk drive cable (40-pin, pitch 2.54mm) • 1 parallel port (26-25-pin, pitch 2.
http://www.aaeon.com Notice Dear Customer , Thank you for purchasing the SBC-659P board. This user's manual is designed to help you to get the most out of the SBC-659 P , please read it thoroughly before you install and use the board.
Contents Chapter 1: General Information. ........................................1 Introduction.......................................................2 Features .................................................................................... 3 Specifications .
Audio Connector(CN9).............................................30 Ethernet Connector (CN12, CN10)..................................31 COM1(CN13), COM2(CN1 1) Serial Ports..............................32 Internal Keyboard Connector(CN15).............
Chapter 4: Drivers and Utilities ......................................77 Installation of Drivers: Notice ................................................ 7 8 Chipset Driver ......................................................................... 7 9 Ultra A T A Driver .
Chapter 1 General Information 1 1 General Information This chapter gives background information of the mainboard. Sections Include: • Board Specifications • Layout and Dimensions CHAPTER.
2 SBC-659P User Manual If your requirements for a single board computer consist of a half-sized footprint, dual Ethernet, PISA interface and Intel quality logic chipset, then SBC-659P is the solution. This half-sized single board computer is ideal for internet data access server .
Chapter 1 General Information 3 Features Supports Intel Celeron/ Tualatin/Pentium III FC-370 CPUs Notice: It doesn't support 0.25 micron process micron process micron process micron process micron process CPU.
4 SBC-659P User Manual Standard Half-size SBC functions • CPU : FC-370 Pentium III (Coppermine), Celeron, Tualatin and compatible CPUs (W ith system bus frequencies of 66/100/133MHz). • CPU socket : 370 pins Socket • BIOS : A ward 2 MB Flash BIOS • Chipset : Intel 815E • I/O chipset : ITE 8712F .
Chapter 1 General Information 5 Flat Panel/CRT Interface • Chipset : embedded In Intel 815E • Display memory : Share system memory 4MB SDRAM (Max) • Display typ e : Supports non-interlaced C R T and up to 18/24/36/48 bit LCD (TFT LCD, only). Can display both CR T and Flat Panel simulta neously .
6 SBC-659P User Manual OS version recomandation: Win 98 or above Mechanical and environmental Power supply voltage : +5V , -5V , +12V , -12V Operating temperature : 32 to 140 o F (0 to 60 o C) Board size : 7.3"(L) x 4.8"(W) (185mm x 122mm) W eight : 0.
Chapter 1 General Information 7 Board Layout.
8 SBC-659P User Manual Board Dimensions.
Chapter2 Installation 9 2 Installation This chapter describes how to set up the main board hardware, including instruc- tions on setting jumpers and connecting peripherals, switches, and indicators. Be sure to read all the safety precautions before you begin the installation proce- dure.
SBC-659P 10 SBC-659P Installation Guide BC-599/596 Safety precautions Warning! Always completely disconnect the power cord from your chassis whenever you are working on it. Do not make connections while the power is on because sensitive electronic components can be damaged by the sudden rush of power .
Chapter2 Installation 11 Installing A CPU T o install the CPU, follow the instructions that came with it. If no documentation was provided, the general procedures for installing a CPU are outlined below: 1 . Lubricate the pins on the CPU with lubricant for PGA devices.
SBC-659P 12 SBC-659P Installation Guide BC-599/596 1 3 2 Open Closed Closed 2-3 Open Closed Closed 2-3 1 2 3 Setting jumpers Y ou configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch.
Chapter2 Installation 13 Installing SODIMM Supplementary information about DIMM Y our SBC-659P can accept both regular and PC-100/133 SDRAM DIMM Module. Onboard one 144-pin SODIMM socket supports up to 256MB of memory . Single-sided modules are typically 16 or 128MB; double-sided modules are usually 32 or 256 MB.
SBC-659P 14 SBC-659P Installation Guide BC-599/596 JP1(1-2) Front Panel (Power On Button) JP1(3-4) Front Panel (IDE Driver LED) JP1(5-6) Front Panel (External Speaker) JP1(7-8) Front Panel (Case Open).
Chapter2 Installation 15 Connectors Connector Function CN1 DVO Output Connector CN2 External Power On Connector CN3 IDE Connector (A T A100) CN4 No used CN5 USB 2-3 Connector CN6 USB 0-1 Connector CN7.
SBC-659P 16 SBC-659P Installation Guide BC-599/596 Locating Jumpers and Connectors.
Chapter2 Installation 17 Locating of Solder Side Connectors CN22 D I MM1.
SBC-659P 18 SBC-659P Installation Guide BC-599/596 Mechanical Drawing.
Chapter2 Installation 19 Mechanical Drawing 0 0.
SBC-659P 20 SBC-659P Installation Guide BC-599/596 Clear CMOS (JP2) Y ou can use JP2 to clear the CMOS data if necessary . T o reset the CMOS data, place a jumper on JP2 (Clear CMOS) for just a few seconds, and then remove the jumper to the (Protect) position.
Chapter2 Installation 21 System Frequency (JP3) CPU/Auto Detect SDRAM/Auto Detect 1 2 3 4 *Default: Auto Detect.
SBC-659P 22 SBC-659P Installation Guide BC-599/596 COM2 (Ring, +5V, +12V) JP4 +12V 2 4 6 1 3 5 +5V Ring Default 1 3 5 1 3 5 2 4 6 2 4 6.
Chapter2 Installation 23 RS-232/422/485 COM2(JP5,JP6) Setting RS-232 JP5 JP6 RS-422 JP5 JP6 RS-485 JP5 JP6 Default 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 3 4 6 7 9 10 12 1 3 4 6 7 9 10 12 1 3 4 6 7 9 1.
SBC-659P 24 SBC-659P Installation Guide BC-599/596 Digital Video Output Connector (CN1) Digital V isual Output Connector (CN1) Pi n Signal Pi n Signal A 1 FTCLK0 B 1 FTD0 A 2 FTCLK1 B 2 FTD1 A 3 CR T-.
Chapter2 Installation 25 External Power On Connector (CN2) External Power On Connector (CN2) Pin Signal 1 N C 2 G N D 3 N C 4 G N D 5 PS-ON 6 5VSB.
SBC-659P 26 SBC-659P Installation Guide BC-599/596 IDE hard drive connector (CN3) Pin Signal Pin Signal 1 IDE RESET 2 G N D 3D A T A 7 4D A T A 8 5D A T A 6 6D A T A 9 7D A T A 5 8D A T A 1 0 9 D AT A.
Chapter2 Installation 27 USB connector (CN5, CN6) The SBC-659P provides four USB (Universal Serial Bus) interfaces, which give complete plug and play , hot attach/detach for up to 127 external devices. The USB interfaces comply with USB specifica- tion Rev .
SBC-659P 28 SBC-659P Installation Guide BC-599/596 Floppy Drive Connector (CN7) Floppy drive connector (CN7) Pin Signal Pin Signal 1 G N D 2 DENSITY SELECT 3 G N D 4 N.
Chapter2 Installation 29 VGA connector (CN8) VGA display connector (CN8) CN8 is a 15-pin, D-SUB connector used for conventional CR T displays. VGA display connector (CN8) Pin Signal Pin Signal 1 RED 9.
SBC-659P 30 SBC-659P Installation Guide BC-599/596 Audio Connector (CN9) On board SBC-659P , there is a 14-pin header for audio capability . The pin definition is provided below .
Chapter2 Installation 31 Ethernet Connectors(CN12,CN10) Onboard supports two standard RJ-45 connector for Ethernet connection. The RJ-45 connector has two LED indicators.
SBC-659P 32 SBC-659P Installation Guide BC-599/596 COM 1 RS-232 (CN13) Pin Signal Pin Signal 1 DCD1 2 RXD1 3 TXD1 4 DTR1 5 GND 6 DSR1 7 R TS1 8 CTS1 9 R I 1 0 N.C. COM 1 (CN 13) & COM 2 (CN 11) Serial Ports On board offer two serial ports for serial devices connection.
Chapter2 Installation 33 Power connector (CN16) A TX power connector (CN16) The A TX power supply uses 20-pin connector shown below . Make sure you plug in the right direction.
SBC-659P 34 SBC-659P Installation Guide BC-599/596 Parallel port connector (CN17) Normally , the parallel port is used to connect the board to a printer . The SBC-659P includes an onboard parallel port, accessed through CN17, a 26-pin flat-cable connector .
Chapter2 Installation 35 IrDA Connector (CN19) The IrDA connector (CN19) can be configured to support wireless infrared modules. W ith this module and application software such as laplink or W in95, Direct Cable connection can transfer files between laptops, notebooks, PDA and printers.
SBC-659P 36 SBC-659P Installation Guide BC-599/596 CPU Fan power connectors (CN20) Plug in the fan cable to the 3-pin fan connector onboard. The fan connector is marked CN20.
Chapter2 Installation 37 Compact Flash Connector (CN22) Pi n Signal Pin Signal 1 GND 26 GND 2D A T A 3 2 7 D A T A 1 1 3 DA T A4 2 8 DA T A12 4 DA T A5 2 9 DA T A13 5 DA T A6 3 0 DA T A14 6 DA T A7 3 .
38 SBC-659P User Manual 3 Award BIOS Setup This chapter describes how to configure the BIOS for the system. CHAPTER.
Chapter 3 Award BIOS Setup 39 Starting setup The A ward BIOS is immediately activated when you first turn on the computer . The BIOS reads system configuration information in CMOS RAM and begins the process of checking out the system and configuring it through the power-on self test (POST).
40 SBC-659P User Manual Setup keys These keys helps you navigate in A ward BIOS: Up arrow Move to previous item Down arrow Move to next item Left arrow Move to the item in the left hand Right arrow Mo.
Chapter 3 Award BIOS Setup 41 Getting Help Press F1 to pop up a small help window that describes the appro- priate keys to use and the possible selections for the highlighted item.
42 SBC-659P User Manual Main Setup Menu Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.) Advanced BIOS Features Use this menu to set the advanced features available on your system.
Chapter 3 Award BIOS Setup 43 PnP/PCI Configuration This entry appears is your system supports PnP/PCI. PC Health Status This menu allows you to set the shutdown temperature for your system. Frequency/V oltage Control Use this menu to specify your settings for frequency/ voltage control.
44 SBC-659P User Manual Standard CMOS Features This standard setup menu allows users to configure system components such as the date, time, hard disk drive, floppy drive, display , and memory . Online help for each field can be accessed by pressing F1.
Chapter 3 Award BIOS Setup 45 If you do not want to select drive type AUTO, other methods of selecting the drive type are available: 1.Match the specifications of your installed IDE hard drive(s) with the preprogrammed values for drive types 1 through 45.
46 SBC-659P User Manual - LBA (Logical Block Addressing): During drive access, the IDE controller transforms the data address described by sector , head, and cylinder number into a physical block address, significantly improving data transfer rates. For drives with greater than 1024 cylinders.
Chapter 3 Award BIOS Setup 47 Halt On During the power-on-self-test (POST), the computer stops if the BIOS detects a hardware error . Y ou can tell the BIOS to ignore certain errors during POST and continue the boot-up process. These are the selections: No errors : POST does not stop for any errors.
48 SBC-659P User Manual Extended Memory Above the 1-MB boundary . Early IBM personal computers could not use memory above 1 MB, but current PCs and their software can use extended memory . Other Memory Between 640 KB and 1 MB; often called High memory .
Chapter 3 Award BIOS Setup 49 A dvanced BIOS Features The displayed configuration is based on the manufacturer's SETUP DEF AUL TS settings. Virus W arning When enabled, you receive a warning message if a program (specifically , a virus) attempts to write to the boot sector or the partition table of the hard disk drive.
50 SBC-659P User Manual CPU Internal Cache/External Cache Cache memory is additional memory that is much faster than conventional DRAM (system memory). CPUs from 486-type on up contain internal cache memory , and most, but not all, modern PCs have additional (external) cache memory .
Chapter 3 Award BIOS Setup 51 Swap Floppy Drive This field is effective only in systems with two floppy drives. Selecting enabled assigns physical drive B to logical drive A, and physical drive A to logical drive B. Boot Up Floppy Seek When Enabled, the BIOS tests (seeks) floppy drives to determine whether they have 40 or 80 tracks.
52 SBC-659P User Manual T ypematic Rate Setting- Key strokes repeat at a rate determined by the keyboard controller . When enabled, the typematic rate and typematic delay can be selected. The choice: Enabled/Disabled T ypematic Rate (Chars/Sec)- Sets the number of times a second to repeat a key stroke when you hold the key down.
Chapter 3 Award BIOS Setup 53 HDD S.M.A.R.T Capability Hard disk drives have built in problem detection capability (Self-Monitoring Analysis and Reporting T echnology). If a foreseen problem is about to take place, the computer will give a you a warning signal.
54 SBC-659P User Manual Advanced Chipset Features SDRAM CAS Latency T ime When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. Do not reset this field from the default value specified by the system designer .
Chapter 3 Award BIOS Setup 55 SDRAM RAS Precharge T ime If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster performance; slow gives more stable performance.
56 SBC-659P User Manual AGP Graphics Aperture Size Select the size of Accelerated Graphics Port (AGP) aperture. The aperture is a portion of the PCI memory address range dedicated for graphics memory address space. Host cycles that hit the aperture range are forwarded to the AGP without any translation.
Chapter 3 Award BIOS Setup 57 RAS-to-CAS Override Select the display cache clock periods control. The choice:Fast,Slow RAS#T iming This item controls RAS#active to Protegra, and refresh to RAS# active delay(in local memory clocks), RAS#Per charge Timing This item controls RAS#precharge(in local memory clocks).
58 SBC-659P User Manual Integrated Peripherals On-Chip Primary PCI IDE The system chipset contains a PCI IDE interface with support for two IDE channels. Select Enabled to activate the primary and/or secondary IDE interface. Select Disabled to deactivate this interface, if you install a primary and/or secondary add-in IDE interface.
Chapter 3 Award BIOS Setup 59 IDE Primary/Secondary Master/Slave UDMA Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (W indows 95 OSR2 or a third-party IDE bus master driver).
60 SBC-659P User Manual Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field.
Chapter 3 Award BIOS Setup 61 Onboard Serial Ports (1, 2) Normally , the main board’ s I/O chips will occupy a certain portion of memory space. For each I/O device the computer provides an I/O address. The more devices attached the more address needed to organize the memory storage areas.
62 SBC-659P User Manual W atch Dog Timer Y ou can enable the system watchdog timer , a hardware timer that generates either an NMI or a reset when the software that it monitors does not respond as exp.
Chapter 3 Award BIOS Setup 63 Power Management Setup ACPI Function This item allows you to enable/disable the Advanced Configuration and Power Management (ACPI).
64 SBC-659P User Manual Power Management This category allows you to select the type ( or degree ) of power saving and is directly related to the following modes: 1. HDD Power Down 2. Doze Mode 3. Suspend Mode ) t l u a f e D ( e l b a s i D. s e d o m r u o f l l a e l b a s i D .
Chapter 3 Award BIOS Setup 65 V ideo Off In Suspend After the selected period of system inactivity , the chipset enters a hardware suspend mode, stopping the CPU clock and possibly causing other system devices to enter power management modes. In this case the video hardware can be selected to shut off after a period of system inactivity .
66 SBC-659P User Manual Power On By Ring An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) boots the system from a soft off state. Resume By Alarm This option is used to Enable/Disable USB keyboard wake up with suspend to RAM.
Chapter 3 Award BIOS Setup 67 PnP/PCI Configurations PnP OS installed This item allows you to determine install PNP OS or not. The choice: Y es,No Reset Configuration Data Normally , you leave this field disabled.
68 SBC-659P User Manual Resources Contr olled By The A ward Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices. However , this capability means absolutely nothing unless you are using a Plug and Play operating system such as W indows ® 95.
Chapter 3 Award BIOS Setup 69 PC Health Status Shutdown T emperature Y our system can be configured to shutdown once reaching a certain temperature. T o protect your system from overheating or damage, select a certain temperature level in the PC Health Status menu.
70 SBC-659P User Manual Frequency/V oltage Control Auto Detect DIMM/PCI CLK This item allows you to enable/disable auto detect DIMM/PCI clock. The choices: Enable/Disable Spread Spectrum This allows you to enable/disable the spread spectrum modulate. When the system clock generator pulses, the extreme values of the pulse generate excess EMI.
Chapter 3 Award BIOS Setup 71 Load Fail-Safe Defaults Load Fail-Safe Defaults When you press <Enter> on this item you get a confirmation dialog box with a message similar to: Load Fail-Safe Default (Y/N)? Pressing “Y” loads the BIOS default values for the most stable, minimal performance system operations.
72 SBC-659P User Manual Load Optimized Default Load Optimized Default When you press <Enter> on this item you get a confirmation dialog box with a message similar to: Load Optimized Defaults (Y/.
Chapter 3 Award BIOS Setup 73 Set Supervisor Password When you select this function, a message appears at the center of the screen: ENTER P ASSWORD: T ype the password, up to eight characters, and press Enter . T yping a password clears any previously entered password from CMOS memory .
74 SBC-659P User Manual Set User Password When you select this function, a message appears at the center of the screen: ENTER P ASSWORD: T ype the password, up to eight characters, and press Enter . T yping a password clears any previously entered password from CMOS memory .
Chapter 3 Award BIOS Setup 75 Save to CMOS and EXIT Save to CMOS and EXIT Pressing <Enter> on this item asks for confirmation: Save to CMOS and Exit (Y/N)? Pressing “Y” stores the selections made in the menus in CMOS, a special section of memory that stays on after you turn your system off.
76 SBC-659P User Manual Exit without Saving Exit Without Saving Pressing <Enter> on this item asks for confirmation: Quit W ithout Saving (Y/N)? This allows you to exit Setup without storing in CMOS any change. The previous selections remain in effect.
77 SBC-659P User Manual CHAPTER This SBC-659P is equipped with an audio, VGA and Dual LAN interface. This chapter provides instructions for installing the software drivers on these pheripherals.
78 SBC-659P User Manual Installing Drivers Notice: Attention First if using operating systems such as Windows 95/98/2000 ® a chipset driver must be installed before VGA, LAN or Audio drivers are installed. Second if using Windows 95/98/2000® operating systems an Ultra A T A storage driver must also be installed after the chipset driver .
79 SBC-659P User Manual Installing Chipset Driver for Windows 95/98/ 2000® The chipset driver must be installed in order to proceed to LAN, VGA and AUDIO drivers. ==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen.
80 SBC-659P User Manual Installing Ultra ATA Storage Driver for Windows 95/98/ 2000® The Ultra A T A Storage Driver must be installed in order to use Windows 95/98/2000 ® operating systems. ==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen.
81 SBC-659P User Manual Installing Intel 82559 for Windows 95 or 98 Ver. 1.0® ==>Place the Driver CDROM into your CDROM drive. ==>Click on Start button ==>Click on Settings button ==>Clic.
82 SBC-659P User Manual Installing VGA for Windows 95/98® ==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen.. ==>Click on Intel folder ==>Click on 810_81.
83 SBC-659P User Manual Installing Audio for Windows 95/98® ==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen.. ==>Click on Sound folder ==>Click on Alc 200 folder ==>Click on Win98 folder ==>Click on V1.
84 SBC-659P User Manual Installing Security Driver for Windows NT® Please perform this procedure first ==>Place the Driver CDROM into your CDROM drive.
85 SBC-659P User Manual Installing Ultra ATA Storage Driver for Windows NT® The Ultra A T A Storage Driver must be installed in order to use Windows NT ® operating systems. ==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen.
86 SBC-659P User Manual Installing VGA for Windows NT® ==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen.. ==>Click on VGA folder ==>Click on Intel folde.
87 SBC-659P User Manual Installing Audio for Windows NT® ==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen.. ==>Click on Sound folder ==>Click on Alc 200 folder ==>Click on WinNT folder ==>Click on V1.
88 SBC-659P User Manual Installing Intel 82559 for Windows NT® ==>Place the Driver CDROM into your CDROM drive. ==>Click on Start button ==>Click on Settings button ==>Click on Control Panel button ==>Click on Network ==>Click on yes ==>Click on next ==>Click on Select from list.
89 SBC-659P User Manual Installing VGA for Windows 2000® ==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen.. ==>Click on VGA folder ==>Click on Intel fol.
90 SBC-659P User Manual Installing Audio for Windows 2000® ==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen.. ==>Click on Sound folder ==>Click on Alc 200 folder ==>Click on Win2000 folder ==>Click on V1.
Een belangrijk punt na aankoop van elk apparaat IBM SBC-659P (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen IBM SBC-659P heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens IBM SBC-659P vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding IBM SBC-659P leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over IBM SBC-659P krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van IBM SBC-659P bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de IBM SBC-659P kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met IBM SBC-659P . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
