Gebruiksaanwijzing /service van het product 281786-002 van de fabrikant Intel
Ga naar pagina of 36
Advanced/ZP Baby-AT Board Technical Product Summary Version 2 July, 1995 Order Number 281786-002 ®.
Advanced/ZP Technical Product Summary • Page 2 Advanced/ZP Technical Product Summary Table of Contents Introduction .....................................................................................................................................
Advanced/ZP Technical Product Summary • Page 3 Introduction The Intel Advanced/ZP baseboard features the Pentium processor in a Baby-AT form factor with integrated I/O. Advanced/ZP baseboards are focused on providing the best possible performance at the lowest possible price for mainstream desktop computers.
Advanced/ZP Technical Product Summary • Page 4 BASEBOARD DESIGN EXCEPTIONS BASEBOARD DIMENSIONS The Advanced/ZP is 3.0" shorter than the Baby-AT standard. The shorter board length may require some chassis to be modified to add additional mounting holes.
Advanced/ZP Technical Product Summary • Page 5 Board Level Features A − Two PCI IDE interfaces B − National 87306 I/O controller C − Primary power connector D − Four SIMM sockets (two banks).
Advanced/ZP Technical Product Summary • Page 6 SYSTEM MEMORY The Advanced/ZP baseboard provides four 72-pin SIMM sites for memory expansion. The sockets support 1M x 32 (4 MB), 2M x 32 (8 MB), 4M x 32 (16 MB), and 8M x 32 (32 MB) single-sided or double-sided SIMM modules.
Advanced/ZP Technical Product Summary • Page 7 PERIPHERAL COMPONENT INTERCONNECT (PCI) PCISET The Intel Triton 82430FX PCIset consists of the 82437FX Triton System Controller (TSC), two 82438FX Triton Data Path (TDP) devices, and one 82371FB PCI ISA/IDE Accelerator (PIIX) bridge chip.
Advanced/ZP Technical Product Summary • Page 8 IDE SUPPORT The Advanced/ZP baseboard provides two independent high performance bus-mastering PCI IDE interfaces capable of supporting PIO Mode 3 and Mode 4 devices for up to 16 MB/sec transfers. Support for ATAPI devices is provided in the system BIOS.
Advanced/ZP Technical Product Summary • Page 9 the CMOS RAM values can be cleared to the system defaults by using a configuration switch on the baseboard. Appendix B lists switch and jumper configurations. An external coin-cell style battery provides power to the RTC and CMOS memory.
Advanced/ZP Technical Product Summary • Page 10 • The Flash BIOS can be updated from a file on a disk; • The current BIOS code can be copied from the Flash EEPROM to a disk file as a backup in t.
Advanced/ZP Technical Product Summary • Page 11 SECURITY FEATURES ADMINISTRATIVE PASSWORD The administrative password protects several sensitive Setup options from being viewable to a user unless the password is entered. These sensitive fields are viewable unless the administrative password is set.
Advanced/ZP Technical Product Summary • Page 12 Figure 3. Front Panel Connectors Sleep/Resume This two pin header, when connected to a momentary switch, can be used to put the system into a power managed state (standby) that will reduce the system ’ s power consumption.
Advanced/ZP Technical Product Summary • Page 13 from an on-board voltage regulator from the +5 volt source. This information is provided only as a guide for calculating approximate total system power usage with additional resources added. CURRENT DC Voltage 75 MHz Typical Current* 90 MHz Typical Current* +5V 3.
Advanced/ZP Technical Product Summary • Page 14 Appendix A − User-Installable Upgrades SYSTEM MEMORY Table A-1 shows the possible memory combinations. The Advanced/ZP will support both Fast Page DRAM or EDO DRAM SIMMs, but they cannot be mixed within the same memory bank.
Advanced/ZP Technical Product Summary • Page 15 Appendix B − Jumpers and Switches Figure B-1. Jumper locations and settings (default settings shown) EXTERNAL CPU CLOCK SPEED (50/60/66 MHZ) - SWITCHES 7 & 8 This jumper sets the CPU's external operating frequency at 50, 60, and 66 MHz.
Advanced/ZP Technical Product Summary • Page 16 PROCESSOR VOLTAGE REGULATION - SWITCH 2 Sets the output of the on-board voltage regulator. The switch settings are OFF = VR, and ON = VRE. The VR voltage specification requires a voltage range of 3.3-3.
Advanced/ZP Technical Product Summary • Page 17 Appendix C − I/O Map Address (hex) Size Description 0000 - 000F 16 bytes PIIX - DMA 1 0020 - 0021 2 bytes PIIX - Interrupt Controller 1 0040 - 0043 .
Advanced/ZP Technical Product Summary • Page 18 Appendix D − Memory Map Address Range (Decimal) Address Range (hex) Size Description 1024K-131072K 100000-8000000 127M Extended Memory 960K-1023K F0.
Appendix F − Connectors POWER SUPPLY CONNECTORS PRIMARY POWER (J9J1) Pin Name Function 1 PWRGD Power Good 2 +5 V + 5 volts Vcc 3 +12 V + 12 volts 4 -12 V - 12 volts 5 GND Ground 6 GND Ground 7 GND Ground 8 GND Ground 9 -5 V -5 volts 10 +5 V + 5 volts Vcc 11 +5 V + 5 volts Vcc 12 +5 V + 5 volts Vcc AUXILIARY (3.
Advanced/ZP Technical Product Summary • Page 20 I/O CONNECTORS AT Keyboard Connector (J8k1) Pin Signal Name 1 Clock 2 Data 3 No Connect 4 Ground 5 Vcc (fused) Table F-11. Keyboard Connector Serial Ports (j7k1, j7k2) Pin Signal Name 1 DCD 2 DSR 3 Serial In - (SIN) 4 RTS 5 Serial Out - (SOUT) 6 CTS 7 DTR 8 RI 9 GND 10 N.
Advanced/ZP Technical Product Summary • Page 21 ISA CONNECTORS (J1G1, J2G1, J2G2, J3G1) Signal Name Pin Pin Signal Name GND B1 A1 IOCHK- RSTDRV B2 A2 SD7 Vcc B3 A3 SD6 IRQ9 B4 A4 SD5 -5V B5 A5 SD4 D.
Advanced/ZP Technical Product Summary • Page 22 PCI CONNECTORS (J4G1, J5G1, J5G2) Signal Name Pin Pin Signal Name Signal Name Pin Pin Signal Name GND A1 B1 -12V AD16 A32 B32 AD17 +12V A2 B2 No Connect 3.3V A33 B33 CBE2- No Connect A3 B3 GND FRAME- A34 B34 GND No Connect A4 B4 No Connect GND A35 B35 IRDY- Vcc A5 B5 Vcc TRDY- A32 B32 3.
Advanced/ZP Technical Product Summary • Page 23 Appendix G − BIOS Setup OVERVIEW OF THE SETUP MENU SCREENS The Setup program initially displays the Main menu screen. In each screen there are options for modifying the system configuration. Select a menu screen by pressing the left < ← > or right < → > arrow keys.
Advanced/ZP Technical Product Summary • Page 24 When selected, this brings up the Floppy Options submenu. Hard Disk 0:, 1:, 2:, 3: This reports if a hard disk is connected to the system. When selected, this brings up the Hard Disk Configuration submenu.
Advanced/ZP Technical Product Summary • Page 25 Number of Cylinders If Hard Disk Type is set to User Definable, you must type the correct number of cylinders for your hard disk. If Hard Disk Type is set to Auto Configured, this reports the number of cylinders for your hard disk and cannot be modified.
Advanced/ZP Technical Product Summary • Page 26 BOOT OPTIONS SUBMENU Boot Sequence When selected, this brings up a dialog box that allows you to set the order of drives the system uses to find an operating system to boot from. The following options are available: C: First, Then A: The system checks drive C first, followed by drive A.
Advanced/ZP Technical Product Summary • Page 27 Typematic Rate When selected, this brings up a dialog box that allows you to set the speed at which characters repeat when you hold down a key on the keyboard. The higher the number, the faster the characters repeat.
Advanced/ZP Technical Product Summary • Page 28 PCI IDE Interface When selected, this brings up a dialog box that allows you to enable the PCI IDE hard disk interface. The options are Enabled and Disabled. The default is Enabled. (If Configuration Mode is set to Auto, this option cannot be modified.
Advanced/ZP Technical Product Summary • Page 29 Serial Port 2 IRQ This reports the IRQ number for serial port 2. This is informational only, and there are no options. If the Serial Port 2 Address field is set to Disabled, this field will not be visible.
Advanced/ZP Technical Product Summary • Page 30 IDE Drive Power Down When selected, this brings up a dialog box that allows you to set any IDE drives to spin down when the system goes into power managed mode. The options are Enabled and Disabled. The default is Enabl ed.
Advanced/ZP Technical Product Summary • Page 31 available. If an interrupt is available, the PCI auto-configuration code can assign the interrupt to be used by the system. If your system contains an ISA agent that uses one of these interrupts, select Used By ISA Card for that interrupt.
Advanced/ZP Technical Product Summary • Page 32 Set Administrative Password When selected, this brings up a dialog box that allows you to set the Administrative password. Unattended Start When selected, this brings up a dialog box that allows you to control when the security password is requested.
Advanced/ZP Technical Product Summary • Page 33 Appendix H − BIOS Recovery The Advanced/ZE incorporates the AMIBIOS in a Flash memory component. Flash BIOS allows easy upgrades without the need to replace an EPROM. The upgrade utility fits on a floppy diskette and provides the capability to save, verify, and update the system BIOS.
Advanced/ZP Technical Product Summary • Page 34 Appendix I − Error messages and Beep Codes Errors can occur during POST (Power On Self Test) which is performed every time the system is powered on. Fatal errors, which prevent the system to continue the boot process, are communicated through a series of audible beeps.
Advanced/ZP Technical Product Summary • Page 35 ERROR MESSAGES (CONT.) FDD Controller Failure The BIOS cannot communicate with the floppy disk drive controller. Check all appropriate connections after the system is powered down. HDD Controller Failure The BIOS cannot communicate with the hard disk drive controller.
Advanced/ZP Technical Product Summary • Page 36 Appendix J − Environmental Standards Parameter Condition Specification Temperature Non-Operating -40 o C to +70 o C Operating +0 o C to +55 o C Humidity Non-Operating 92% Relative Humidity max. @ 36 o C Operating 80% Relative Humidity max.
Een belangrijk punt na aankoop van elk apparaat Intel 281786-002 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Intel 281786-002 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Intel 281786-002 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Intel 281786-002 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Intel 281786-002 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Intel 281786-002 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Intel 281786-002 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Intel 281786-002 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.