Gebruiksaanwijzing /service van het product ECB-870 van de fabrikant Intel
Ga naar pagina of 115
Part No.2047870000 User’s Manual ECB-870 Intel Pentium 4 Full-size CPU Card w ith Dual 10/100 Base-Tx Ethernet 1 st Ed. – 20 May 2002.
ECB-870 Evalue Technolog y Inc. FCC STA TEMENT THIS DEVICE COMPLIES W ITH PART 15 FCC RU LES. OPERATION IS SUBJECT TO THE FOLLOW ING TW O CONDIT IONS: (1) THIS DE VICE MAY NOT CAUS E HARMFUL INTERFE RENCE. (2) THIS DEVICE M UST ACCEPT ANY INTERFER ENCE RECEIVED INCL UDING INTERFERENCE T HAT MAY CAUS E UNDESIRED OPERATION.
User’s Manual Evalue Technolog y Inc. Copy right Notice Copyr ight 2001, 2002, Ev alue Technology Inc., ALL RIGHTS RESERVED. No part of this document may be repr oduced, copied, translated, or t.
ECB-870 Evalue Technolog y Inc. A Message to the Customer Evalue C ustomer Serv ices Each and every Evalue’s pr oduct is built to the most ex acting speci fications to ensure reliabl e performance in the harsh and demanding conditions ty pical of industrial envir onments.
User’s Manual Evalue Technolog y Inc. Product Warranty Evalue warrants to you, the orig inal purchaser, that each of its products will be free from defects in materials and w orkmanship for tw o years from the date of purchase.
ECB-870 Evalue Technolog y Inc. Packing List Before you begin installing y our single board, please make sure that the following materials hav e been shipped: 1 ECB-870 Pentium 4 Ful l-siz e singl.
User’s Manual Evalue Technolog y Inc. 1. MA NUAL OBJECTIVES .............................................................................................1 2. INTRODUCTION ..............................................................................
ECB-870 Evalue Technolog y Inc. 3.9 Setting Jumpers ................................................................................................... 21 3.9.1 COM2 R S-232/422/485 Sel ect (J1, J2, JCSE L) ............................................
User’s Manual Evalue Technolog y Inc. 4.4 In Case of Problems............................................................................................. 46 4.5 Main Menu..............................................................................
ECB-870 Evalue Technolog y Inc. A PPENDIX A : BIOS REVISIONS ......................................................................................87 A PPENDIX B: S YSTEM RESOURCES ......................................................................
User’s Manual Evalue Technolog y Inc. BIOS R OM C hecksu m Error - Sy stem Halted . ........................................................................ 97 Me mory Test Fai l. .....................................................................
ECB-870 Evalue Technolog y Inc. Document A mendment History Revision Date By Comment 1 st May. 2002 Harri s Chen Initial Rel ease.
ECB-870 ECB-870 Us er’s Manual 1 1. Manual Objectives This manual describes i n detail the Ev alue Technology ECB-870 Sing le Board. W e have tried to i nclude as much information as possible but w .
User’s Manual 2 ECB-870 Us er’s Manual 2. Introducti on 2.1 Sy stem Overv iew The ECB-870 is an all -in-one Ful l-siz e Pentium 4 Sing le Board Computer ( SBC) desig ned wi th Intel embedded chipset 845E whi ch supports the latest Intel m- PGA 478 Pentium 4 CPU up to 2.
ECB-870 ECB-870 Us er’s Manual 3 2.2 Sy stem Specifications General Functi ons • CPU: Intel Pentium 4 CPU up to 2.2 GHz + at 400 MHz of FSB • CPU Socket: Intel Socket 478 • BIOS: Award 2 M b P.
User’s Manual 4 ECB-870 Us er’s Manual IDE RAID Interface (Optional) • Chipset: Promi se PDC20265R har dware PC I to UltraATA/100 IDE RAID controller • RA ID Level: RAID Level 0 striping and l.
ECB-870 ECB-870 Us er’s Manual 5 2.3 A rchitecture Overv iew The following block diagr am shows the archi tecture and main components of ECB-870. Two maj or chipsets on board ar e the 82845 Graph Memory Control Hub and 82801BA ICH2.
User’s Manual 6 ECB-870 Us er’s Manual 2.3.1 82845 MCH and 82801BA The Intel ® 845 chipset is desig ned, val idated, and optimiz ed for the Intel Pentium 4 processor with NetBurst micro-architecture using proven and established building blocks.
ECB-870 ECB-870 Us er’s Manual 7 USB host interface; 2 host controller s and supports 4 USB ports Integrated LAN contr oller System Manag ement Bus (SMBus) compati ble wi th most I2C devices; ICH2 has both bus master and slave capability AC ’97 2.
User’s Manual 8 ECB-870 Us er’s Manual 2.3.3 A GP Interface A single AGP component or connector (not both) i s supported by the M CH AGP interface. The AGP buff ers operate only i n 1.5 V mode. They are not 3.3 V safe. The AGP interface supports 1x/2x /4x AGP si gnaling and 2x/4x fast w rites.
ECB-870 ECB-870 Us er’s Manual 9 2.3.6 IDE Interface (Bus Master Capability and Sy nchronous DMA Mode) The fast IDE interface supports up to four IDE devices pr ovidi ng an interface for IDE hard disks and CD ROMs. Each IDE device can hav e independent timings.
User’s Manual 10 ECB-870 User ’s Manual 2.3.8.2 Intel 82559 The Ethernet inter face is based on an Intel 82559 Ethernet controll er that supports both 10BASE-T and 100BASE- TX. The 82559 consists of both the Media Access Contr oller (MAC) and the physical l ayer ( PHY) i nterface combined into a singl e component solution.
ECB-870 ECB-870 Us er’s Manual 11 3. Hardw ar e Configurati on This chapter expl ains you the i nstructions of how to set up y our system. The additional information show s y ou how to i nstall M-Sy stems’ DiskOnChip and prog ram the W atchdog Timer .
User’s Manual 12 ECB-870 User ’s Manual 3.3 Socket 478 Processor 3.3.1 Installing Pentium 4 CPU Lift the handling lev er of CPU socket outwards and upw ards to the other end.
ECB-870 ECB-870 Us er’s Manual 13 3.5 M-Sy stems’ DiskOnChip Flash Disk ECB-870 r eserves a 32-pi n DIP socket to support M-Sy stems’ DiskOnC hip flash disk up to 288 MB. The DiskOnChip is based on pure ISA bus and wi thout PnP (Plug and Pl ay) function.
User’s Manual 14 ECB-870 User ’s Manual 3.6.1 SiS 315 4X A GP VGA Controller W ith a 529-pin PBGA package, Si S315 integrates a 4X /2X AGP controll er wi th full sideband or pipel ine support, a 256-bit 3D /2D graphi cs engine and a motion compensation MPEG I/MPEG II accelerator.
ECB-870 ECB-870 Us er’s Manual 15 3.6.2 Promise FastTrak100 UltraA TA /100 IDE RA ID Interface (ECB-870R Only ) The board integrates w ith Promise FastTrak100 UltraATA/100 IDE R AID interface that provi des RAID 0 and 1 functions. The function can enable or disable by jumper JRAID and the RAID lev el can be set on BIOS.
User’s Manual 16 ECB-870 User ’s Manual 3.6.3 Intel 82559(or 82559ER) & 82801BA (ICH2) + 82562ET ( PHY) Net work Controller The 82559 (or 82559ER) and IC H2+PHY is fully integrated 10BASE- T/100BASE-TX LAN solution.
ECB-870 ECB-870 Us er’s Manual 17 3.7 Watchdog Timer Programming W hen the W atch- D og T imer ( WDT ) function is enabled, a system reset will be generated unless an applicati on trigg ers the timer periodicall y w ithin time- out period. This all ows the system to restar t in an orderly way in case of any abnor mal condition is found.
User’s Manual 18 ECB-870 User ’s Manual 3.8 Jumper & Connector 3.8.1 Jumper & Connector Lay out.
ECB-870 ECB-870 Us er’s Manual 19 3.8.2 Jumper & Connector List Connectors on the board are li nked to external dev ices such as hard disk driv es, keyboard, mouse, or floppy dr ives. In addi tion, the board has a number of jumpers that allow you to configure y our system to sui t your appl ication.
User’s Manual 20 ECB-870 User ’s Manual Connectors Label Function Note AT X ATX power connector AT X R 1 Pentium IV + 12V connector CHA SFA N System fan connector 3 x 1 w afer, pitch 2.54mm CPUFA N CPU fan connector 3 x 1 w afer, pitch 2.54mm FLOPPY Floppy connector 17 x 2 header, pi tch 2.
ECB-870 ECB-870 Us er’s Manual 21 3.9 Setting Jumpers You can configure your board to match the needs of your appli cation by setting jumper s. A jumper is the si mplest kind of electric sw itch. It consists of two metal pins and a small metal cl ip (often protected by a pl astic cover) that slides ov er the pins to connect them.
User’s Manual 22 ECB-870 User ’s Manual 3.9.1 COM2 RS-232/422/485 Select ( J1, J2, JCSEL) The ECB-870 COM2 ser ial port can be selected as R S-232, RS-422, or R S-485 by setti ng J1, J2, & JCSEL.
ECB-870 ECB-870 Us er’s Manual 23 3.9.2 LA N2 Enable / Disable Select (J82559) The primary LAN interface is controll ed by Intel IC H2 with Intel 82562ET and setting as LAN1. It prov ides the same performance as Intel 82559 LAN w ith the same driv er.
User’s Manual 24 ECB-870 User ’s Manual 3.9.5 RA ID Enable / Disable Select ( JRA ID, ECB-870R Only ) The board integrates with Promi se FastTrak100 UltraATA/100 IDE RAID interface that provi des RAID 0 and 1 functions. The function can enable or disable by jumper JRAID and the RAID level can be set on BIOS.
ECB-870 ECB-870 Us er’s Manual 25 3.10 Connector Definitions 3.10.1 A TX Powe r Connector (A TX) Signal PIN Signal +12V 10 20 +12V 5V SB 9 19 5V SB NC 8 18 NC GND 7 17 GND +5V 6 16 +5V GND 5 15 GND +5V 4 14 +5V GND 3 13 GND NC 2 12 NC NC 1 11 NC 3.10.
User’s Manual 26 ECB-870 User ’s Manual 3.10.4 Floppy Connector (FLOPPY ) Signal PIN Signal GND 1 2 DRVDEN0# GND 3 4 NC GND 5 6 DRVDEN1# GND 7 8 INDEX# GND 9 10 MOA# GND 11 12 DSB# GND 13 14 DSA# .
ECB-870 ECB-870 Us er’s Manual 27 3.10.5 Signal Description – Floppy Connector (FLOPPY ) RDATA# The read data input signal f rom the FDD. W D# W rite data. T his logic low open drain writes pre- compens ation serial data to the selected FDD. An open drain output.
User’s Manual 28 ECB-870 User ’s Manual 3.10.6 Primary ID E Connector (IDE1) Signal PIN Signal RESET# 1 2 GND PDD7 3 4 PDD8 PDD6 5 6 PDD9 PDD5 7 8 PDD10 PDD4 9 10 PDD11 PDD3 11 12 PDD12 PDD2 13 14.
ECB-870 ECB-870 Us er’s Manual 29 3.10.7 Secondary IDE Connector and RA ID IDE Connector (IDE 2, & IDE 3, 4) Signal PIN Signal RESET# 1 2 GND SDD7 3 4 SDD8 SDD6 5 6 SDD9 SDD5 7 8 SDD10 SDD4 9 10.
User’s Manual 30 ECB-870 User ’s Manual 3.10.8 Signal Description – Primary & Secondary and RA ID IDE Connector (IDE 1, 2, 3, 4) PDA [2:0] Primary Disk A dd ress [2:0]. Thes e signals indicate which byte in either the ATA com mand block or control block is being addressed.
ECB-870 ECB-870 Us er’s Manual 31 PDIOR# Primary Disk IO Read. In norm al IDE this is the com mand to the IDE devic e that it may drive data onto the PDD [15:0] lines.
User’s Manual 32 ECB-870 User ’s Manual PDIORDY Primary IO Channel Ready. In normal IDE m ode, this input signal is direc tly driven by the corres ponding IDE device IORDY signal. In an Ultra DMA/33 read cycle, this signal is used as STROBE, with the PIIX4 latc hing data on rising and falling edges of STRO BE.
ECB-870 ECB-870 Us er’s Manual 33 SDDACK# S econdary DMA A cknowledge. T his signal directly drives the IDE device DMACK# signal. It is asser ted by PIIX 4 to indicate to IDE DMA slave devices that a given data tr ansfer cycle (asser tion of SDIOR# or SDIOW #) is a DMA data tr ansfer cycle.
User’s Manual 34 ECB-870 User ’s Manual 3.10.9 Internal Key board Connector (JA TKB) Signal PIN KCLK 1 KDAT 2 NC 3 GND 4 VCC 5 3.10.10 Signal Description – Internal Keyboard Connector (JA TKB) KCLK Bi-directional c lock signal used to s trobe data/com mands f rom/to the PC-AT keyboard.
ECB-870 ECB-870 Us er’s Manual 35 3.10.12 Fast & Standard IrDA Connector (JIR) Signal PIN PIN Signal +5V 1 6 NC NC 2 7 CIRRX IRRX 3 8 5V Standby GND 4 9 NC IRTX 5 10 NC 3.10.13 Signal Configuration – Fast & Standard IrDA Connector (JIR) IRRX Infr ared Receiver input IRTX Infrared T ransm itter output 3.
User’s Manual 36 ECB-870 User ’s Manual 3.10.16 Serial Port 1 / 2 Connector in RS-422 (JC OM1, JCOM2) Signal PIN Signal NC 10 9 RI CTS 8 7 RTS DSR 6 5 GND TxD+ 4 3 TxD- RxD- 2 1 RxD+ 3.10.17 Signal Description – Serial Port 1 / 2 in RS-422 Mode ( JCOM1, JCOM2) Tx D +/- Serial output.
ECB-870 ECB-870 Us er’s Manual 37 3.10.18 Serial Port 1 / 2 Connector in RS-485 (JC OM1, JCOM2) Signal PIN Signal NC 10 9 CTS/RT S + NC 8 7 CTS/RTS - NC 6 5 GND RxD/Tx D + 4 3 RxD/T xD - NC 2 1 NC 3.10.19 Signal Description – Serial Port 1 / 2 in RS-485 Mode ( JCOM1, JCOM2) RxD/T xD +/- Bi-directional data signal pair.
User’s Manual 38 ECB-870 User ’s Manual 3.10.20 A TX Powe r Controller (JPS) Signal PIN 5V Stand-by 1 GND 2 Power On 3 3.10.21 Wake-On-LA N Connector (JWOL) Signal PIN 5V Stand-by 1 GND 2 Power On 3 3.10.22 10/100 BA SE-Tx Ethernet Connector (LA N1, LA N2) Signal PIN TXD+ 1 TXD- 2 RXD+ 3 NC 4 NC 5 RXD- 6 NC 7 NC 8 3.
ECB-870 ECB-870 Us er’s Manual 39 3.10.24 Parallel Port Connector (PRINT ER) Signal PIN Signal STB# 1 14 AFD# PD0 2 15 ERR# PD1 3 16 INIT # PD2 4 17 SLIN# PD3 5 18 GND PD4 6 19 GND PD5 7 20 GND PD6 .
User’s Manual 40 ECB-870 User ’s Manual 3.10.25 Signal Description – Parallel Port Connector (PRINTER) The following signal descr iption cover s the signal definit ions, when the parall el port is operated in standard centr onic mode. The parallel por t controller also supports the f ast EPP and ECP modes.
ECB-870 ECB-870 Us er’s Manual 41 3.10.26 PS/2 Keyboard C onnector (PS2) Signal PIN Signal NC 6 5 KCLK VCC 4 3 GND NC 2 1 KDAT 3.10.27 PS/2 Mouse Connector (PS2) Signal PIN Signal MCLK 6 5 NC VCC 4 3 GND MDAT 2 1 NC 3.
User’s Manual 42 ECB-870 User ’s Manual 3.10.29 USB Connector (USB A ) Signal PIN CH2 CH1 Signal GND 9 10 GND GND 7 8 GND D1+ 5 6 D2+ D1- 3 4 D2- VCC1 1 2 VCC2 3.10.30 Signal Description – USB Connector (USBA ) D1+ / D1- Dif ferential bi-direc tional data signal for USB channel 0.
ECB-870 ECB-870 Us er’s Manual 43 3.10.31 CRT Connector (VGA ) Signal PIN Signal 6 ANA-G ND RED 1 1 1 NC 7 ANA-G ND GREEN 2 1 2 DDCDAT 8 ANA-G ND BLUE 3 1 3 HSY NC 9 VCC NC 4 1 4 VSYNC 10 DIG-GND DIG-GND 5 1 5 DDCCLK 3.10.32 Signal Description – CRT Connector (VGA ) HSYNC CRT hor iz ontal synchronisation output.
User’s Manual 44 ECB-870 User ’s Manual 4. A w ard BIOS Setup 4.1 Starting Setup The AwardBIOS™ i s immediately activ ated when y ou first power on the computer. The BIOS reads the system i nformation contained in the CMOS and beg ins the process of checking out the system and configuring it.
ECB-870 ECB-870 Us er’s Manual 45 4.2 Using Setup In general, y ou use the arrow keys to highlig ht items, press < Enter> to select, use the PageUp and PageD own key s to change entries, pr ess <F1> for help and press < Esc> to quit.
User’s Manual 46 ECB-870 User ’s Manual 4.3 Getting Help Press F1 to pop up a small help w indow that describes the appr opriate keys to use and the possible selections for the highli ghted item. To exi t the Help W indow pr ess <Esc> or the F1 key ag ain.
ECB-870 ECB-870 Us er’s Manual 47 4.5.1 Setup Items The main menu includes the followi ng mai n setup categories. R ecall that some systems may not incl ude all entries. 4.5.1.1 Standard CMOS Features Use this menu for basic system configurati on. 4.
User’s Manual 48 ECB-870 User ’s Manual 4.5.1.11 Save & Exit Set up Save CM OS value chang es to CMOS and exi t setup. 4.5.1.12 Exit Without Save Abandon all CM OS value chang es and exit setup. 4.5.2 Standard CMOS Setup The items in Standard CM OS Setup Menu are div ided into 10 categor ies.
ECB-870 ECB-870 Us er’s Manual 49 4.5.2.1 Standard CMOS Selection This table show s the selections that you can make on the Standar d CMOS Selection.
User’s Manual 50 ECB-870 User ’s Manual 4.5.2.2 IDE A dapters The IDE adapters control the har d disk driv e. Use a separate sub menu to configur e each hard disk dri ve. Figure 2 show s the IDE primary master sub menu. Use the leg end keys to nav igate thr ough this menu and ex it to the main menu.
ECB-870 ECB-870 Us er’s Manual 51 4.5.3 A dvanced CM OS Setup Defaults This Setup i ncludes all of the adv anced f eatures in the system. The detail descr iptions are specified as below. Figure 3: The A dvanced CMOS Features 4.5.3.1 Virus Warning Allow s y ou to choose the VIRUS W arning feature for IDE Hard Di sk boot sector protection.
User’s Manual 52 ECB-870 User ’s Manual 4.5.3.3 Quick Pow er On Self Test This categ ory speeds up Pow er On Self Test (POST) after y ou power up the computer . If it is set to Enable, BIOS will shorten or skip some check items during POST. Enabled Enable quick POST Disabled Norm al POST 4.
ECB-870 ECB-870 Us er’s Manual 53 4.5.3.11 Typemat ic Delay (Msec) Sets the delay ti me after the key is hel d down before it beg ins to repeat the keys troke. The choice: 250, 500, 750, and 1000. 4.5.3.12 Security Option Select whether the passwor d is requi red ever y time the system boots or only when you enter setup.
User’s Manual 54 ECB-870 User ’s Manual 4.5.4 A dvanced Ch ipset Setup Defaults This Setup is very important to keep system’s stability . If you are not technical person, do not attempt to change any parameters. The best way is to choose optimal default setting.
ECB-870 ECB-870 Us er’s Manual 55 4.5.4.1 DRA M Timing Selectable If your DIM M memory has SPD (Serial Presence Detect) 8- pin IC on module, you can set this option to “By SPD”.
User’s Manual 56 ECB-870 User ’s Manual 4.5.4.9 Video BIOS Cacheable Allow s the video BIOS to be cached for faster v ideo performance. The choice: Enable, Disabl e. 4.5.4.10 Video RA M Cacheable Allow s the video R AM to be cached for faster video per formance.
ECB-870 ECB-870 Us er’s Manual 57 4.5.5 Integrated Peripherals Setup Defaults This section describes I/O r esources assignment for all of on-boar d peripheral dev ices.
User’s Manual 58 ECB-870 User ’s Manual 4.5.5.5 USB Keyboard Support This item lets y ou enable or disabl e the USB keyboar d driv er wi thin the onboard BIOS. The choice: Enable, Disabl e. 4.5.5.6 Init Display First Select “AGP” or “PCI Slot” for sy stem to detect first when boot- up.
ECB-870 ECB-870 Us er’s Manual 59 4.5.5.9 Onboard FDC Controller Select “Enabled” to activate the on-boar d FDC and “D isabled” to activ ate an add-on FDC. The choice: Disable, Enabl e. 4.5.5.10 Onboard Serial Port 1 & 2 Select an address and corr esponding interr upt for the first/second serial por t.
User’s Manual 60 ECB-870 User ’s Manual 4.5.5.18 EPP Mode Select Set parallel por t as EPP1.7 or EPP1.9. The choice: EPP1.7, EPP1.9. 4.5.5.19 ECP Mode Use DMA Select a DMA channel i f parallel port i s set as ECP or ECP+ EPP. The choice: 1, 3. 4.5.
ECB-870 ECB-870 Us er’s Manual 61 4.5.6 Pow er Management Setup Defaults This APM (Adv anced Power Management) determines how much power energy setting below items to handle system pow er resource can save. The following descriptions w ill specify the definition of each item in detai ls.
User’s Manual 62 ECB-870 User ’s Manual 4.5.6.3 VGA BIOS if S3 Resume W hen select S3 or S1&S3 can convenientl y Enables VGA BIOS, Suspend to R AM function and Power On Suspend function. The choice: Auto, Yes, No. 4.5.6.4 Powe r Management Mini Saving Sy stem starts power s aving function when the inactivity period exceeds 1 hour .
ECB-870 ECB-870 Us er’s Manual 63 4.5.6 . 10 HDD Pow er Dow n This instructs hard dr ives to shut off while i n the Power M anagement modes. 4.5. 6 .
User’s Manual 64 ECB-870 User ’s Manual 4.5.6.16 USB KB Wake-up From S3 If your USB KB suppor ts PME (Pow er Management Ev ent) sig nal and this item i s set as Enabled, USB KB peri pherals driv e PME sig nal to wake the sy stem f rom low -power states S3.
ECB-870 ECB-870 Us er’s Manual 65 4.5.7 PnP/ PCI Setup Defaults This section describes config uring the PCI bus sy stem. PCI (Peripheral Component Interconnect) is a system that allows I/O devi ces to operate at speeds nearing CPU’s when they communicate w ith own speci al components.
User’s Manual 66 ECB-870 User ’s Manual 4.5.7.4 IRQ Resources These options specify the bus that the named interr upt request li nes (IRQs) ar e used on.
ECB-870 ECB-870 Us er’s Manual 67 4.5.8 PC Health Status Set up Defaults This setup describes current CPU surface temperature status detected from hardw are monitor sensor. The status showed on screen will include: 4.5.8.1 CPU Warning Temperature Select to enable or di sable the hardw are monitor sensor and set the warni ng temperature.
User’s Manual 68 ECB-870 User ’s Manual 4.5.9.1 Vcore, Vcc3, +5V, +12V, -12V,-5V, VBA T & 5VSB The onboard hardw are monitor i s able to detect the vol tage output by the voltag e regulator s. These values refresh upon any key entry . T he function is optional .
ECB-870 ECB-870 Us er’s Manual 69 4.5.9.3 Frequency Control Setup Defaults 4.5.9.4 CPU Clock Ratio The Ratio of some latest Intel Corporati on fixes CPUs and VIA so the R atio cannot be changed w ith the setting. If it di d not fix by C PU manufacturer, it may be changed w ith the setting.
User’s Manual 70 ECB-870 User ’s Manual 4.5.9.7 CPU Host/3v 66/PCI Clock Choose Default, 100, 103, 105, 107,109,111, 114, 117,120, 127, 130 MHz f or the ex ternal frequency of y our CPU. Y ou can select Default, 66, 69,70,71,73,74,76,78,80,85,87MHz .
ECB-870 ECB-870 Us er’s Manual 71 4.5.12 Set Supervisor/User Password You can assig n, modify, or cancel passw ord setting s. To modify, highli ght “Set Superv isor Password” or “Set User Passw ord” and press the <Enter> key. The screen will prompt y ou (“Enter Passw ord:”).
User’s Manual 72 ECB-870 User ’s Manual 5. Driver Inst allation 5.1 Driver Installat ion for Ethernet A dapter 5.1.1 Window s 9x The best way to install the dri ver for the Ethernet contr oller is to use the plug and play system of W indows 9x. The following procedures illustrate how the installation can be done.
ECB-870 ECB-870 Us er’s Manual 73 • If the ‘ Network adapter s ’ line is present, expand the l ine and remov e the PCI Ethernet Adapter. This is done by selecting the line and clicki ng the ‘ Remove ’ button.
User’s Manual 74 ECB-870 User ’s Manual 4. Click the ‘ Next ’ button to conti nue the driver installation. 5. Specify the location of netw ork adapter and cli ck ‘ Next ’ (see below ).
ECB-870 ECB-870 Us er’s Manual 75 6. Click the ‘ Next ’ button to i nstall the networ k adapter driv er. 7. Click the ‘ Next ’ button..
User’s Manual 76 ECB-870 User ’s Manual 8. Click the ‘ Finish ’ button. 9. To complete the instal lation, reboot the computer by clicking the ‘ Yes ’ button in the wi ndow show n below. 10.After the sy stem restar ts, the network adapter should be installed.
ECB-870 ECB-870 Us er’s Manual 77 5.1.2 Window s NT 4.0 Ethernet Installation A driver f or the Intel 82559 Ethernet controller on board is incl uded in the attached supporting CD-ROM. The dri ver for this adapter is denoted ‘Intel ® PRO Adapter’.
User’s Manual 78 ECB-870 User ’s Manual 2. Double cl ick the ‘ Network ’ icon and click the ‘ Adapters ’ tab on the follow ing w indow . A wi ndow as the one show n below shoul d now appear . 3. Click the ‘ Add... ’ button, and the followi ng wi ndow should appear .
ECB-870 ECB-870 Us er’s Manual 79 4. Click the ‘ Have Disk… ’ button to install the Netw ork adapter dr iver from CD-ROM . A wi ndow as the one show n below shoul d now appear . 5. Locate the path of Network adapter driv er and click the ‘ OK ’ button.
User’s Manual 80 ECB-870 User ’s Manual 6. Select the ‘ Intel® PRO Adapter ’ from the list (as show n below ) and click the ‘ OK ’ button. The Network adapter driv er should now be installed. 7. After the dr iver installation i s complete, Protocols, Ser vices etc.
ECB-870 ECB-870 Us er’s Manual 81 8. Click ‘ Clo se ’ to accept the setting s. 9. IP Address, DNS etc. may now be configur ed for the network to be used. C lick ‘ OK ’ to accept the settings. 10.To complete the driv er installati on, reboot the computer by clicking the ‘ Yes ’ button in the wi ndow show n below.
User’s Manual 82 ECB-870 User ’s Manual 5.2 Driver Installat ion for Display Ad apter 5.2.1 Window s 9x The f ollowing steps will install the d isp la y driv er fo r the ‘SiS315 ’ d isplay controller. 1. Find the director y of the driv er disk w ith SiS315 VGA driv er.
ECB-870 ECB-870 Us er’s Manual 83 3. Click the ‘ Next ’ to conti nue the driver install. If you w ant to stop the installation, click the ‘ Cancel ’. 4. Choose to click the ‘Typi cal ’ / ‘Compact’/ ‘C ustom’ to install the displ ay driv er.
User’s Manual 84 ECB-870 User ’s Manual 5. Click the ‘ Next ’ to conti nue the display dr iver installation. 6. Click the ‘ Next ’ to continue the display driv er installation. The driver files w ill now be read and the display adapter is show n as the fo llow ing.
ECB-870 ECB-870 Us er’s Manual 85 7. T o complete the displ ay dri ver instal lation, reboot the computer by clicking the ‘ Yes ’ button in the wi ndow show n below . 8. Further configurati on of the display adapter may be made f rom the ‘ Displ ay Properties ’ wi ndow (follow step 1 above).
User’s Manual 86 ECB-870 User ’s Manual 9. The ‘Information’ tab allow s you to g et the information for SiS315 display controller..
ECB-870 ECB-870 Us er’s Manual 87 A ppendi x A : BIOS Revisions BIOS Rev. New Features Bugs/Problems Solved Know n Problems.
User’s Manual 88 ECB-870 User ’s Manual A ppendix B: Sy stem Resources Memory Map The following table indicates memor y map of ECB-870. The address ranges specify the runtime code leng th.
ECB-870 ECB-870 Us er’s Manual 89 I/O – Map Certain I/O addr esses are subject to change dur ing boot as PnP managers may relocate devices or functions.
User’s Manual 90 ECB-870 User ’s Manual I/O Port Description Note 0000h-000Fh Dir ect mem ory access controller 0081h-0083h Direct mem ory access controller 0087h-0087h Direct mem ory access contr.
ECB-870 ECB-870 Us er’s Manual 91 Interrupt Usage. The onboard Intel 82801BA prov ides an ISA compatible inter rupt controller with functionality as tw o 8259A interrupt controllers . The two controller s are cascaded to provi de 13 external interrupts.
User’s Manual 92 ECB-870 User ’s Manual DMA -channel Usage The DMA circuitr y incorporates the functionality of two 8237 DMA contr ollers w ith sev en progr ammable channels. The controller s are referenced DM A Controller 1 for channels 0- 3 and D MA Contr oller 2 for channels 4-7.
ECB-870 ECB-870 Us er’s Manual 93 A ppendix C: A W A RD BIOS POST M essages During the Power On Sel f-Test (POST), if the BIOS detects an error req uiring y ou to do something to fix, it will either sound a beep code or display a m essage.
User’s Manual 94 ECB-870 User ’s Manual Display Ty pe Has Changed Since Last Boot Since last pow ering off the system, the displ ay adapter has been changed.
ECB-870 ECB-870 Us er’s Manual 95 Key board Error Or No Key board Present Cannot initi alize the key board. Make sure the keyboard is attached correctly and no keys are being pressed during the boot. If you are purposel y configuri ng the system w ithout a keyboard, set the error halt condition in Setup to HALT ON ALL, B UT KEYBOARD.
User’s Manual 96 ECB-870 User ’s Manual RA M Parity Error – Checking For Segment... Indicates a parity error i n Random Access Memory . Should Be Empty But EISA Board Found Please Run EISA Configuration Utility A vali d board ID w as found in a slot that was configured as hav ing no board ID.
ECB-870 ECB-870 Us er’s Manual 97 Hard Disk(s) Fail ( 10) → → → → Unable To Recalibrate Fixed Disk. Hard Disk(s) Fail ( 08) → → → → Sector Verify Failed. Key board Is Locked Out - Unlock The K ey . BIOS detect the keyboard i s locked.
User’s Manual 98 ECB-870 User ’s Manual A ppendi x D: A W ARD BIOS POST Codes POST Code (hex) Description CFh T est CMOS R/W f unctionality . C0h Early chipset initialization: -Disable shadow RAM -Disable L2 cac he (sock et 7 or below) -Program basic chips et registers C1h Detec t memory -Auto-detection of DRAM siz e, ty pe and ECC.
ECB-870 ECB-870 Us er’s Manual 99 POST Code (hex) Description 12h Use walking 1’s algorithm to check out interfac e in CMOS circuitr y . Als o set real-tim e clock power status , and then check for override. 13h Reserved 14h Program chipset default values into c hipset.
User’s Manual 100 ECB-870 User ’s Manual POST Code (hex) Description 28h Reserved 29h 1. Pr ogram CPU internal MT RR (P6 & PII) for 0- 640K mem ory address. 2. Initialize the APIC for Pentium class CPU. 3. Program early c hipset according to CMOS setup.
ECB-870 ECB-870 Us er’s Manual 101 POST Code (hex) Description 49h 1. Calculate total mem ory by tes ting the last double word of each 64K page. 2. Pr ogram writes alloc ation for AMD K5 CPU. 4Ah Reserved 4Bh Reserved 4Ch Res erved 4Dh Res erved 4Eh 1.
User’s Manual 102 ECB-870 User ’s Manual POST Code (hex) Description 66h Reserved 67h Prepare m emory size information f or function c all: INT 15h ax =E820h 68h Reserved 69h Turn on L2 cac he 6Ah Reserved 6Bh Program chipset regis ters according to item s desc ribed in Setup & Auto-conf iguration table.
ECB-870 ECB-870 Us er’s Manual 103 POST Code (hex) Description 82h 1. Call chipset power m anagement hook . 2. Rec over the text fond used by EPA logo (not for f ull screen logo) 3. If password is set, as k for pas sword. 83h Save all data in stack back to CMOS 84h Initialize ISA PnP boot devices 85h 1.
Een belangrijk punt na aankoop van elk apparaat Intel ECB-870 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Intel ECB-870 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Intel ECB-870 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Intel ECB-870 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Intel ECB-870 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Intel ECB-870 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Intel ECB-870 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Intel ECB-870 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
