Gebruiksaanwijzing /service van het product PCI-X van de fabrikant Intel
Ga naar pagina of 54
DSS NETWORKS GigMAC PMC & PCI/PCI-X Cards GigPMC Switch GigPCI-Express Switch Board and Driver Users Manual (Includes all Intel-based models 5164, 5261, 5262, 5263-SFP, 5264, 5468, 6162, 6267-SFP and 6468) (copper and fiber models) Document Version 2.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 2 1. INTRODUCTION ................................................................................................................ .. 4 1.1 SEE ALSO .
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 3 12.1 ENVIRONMENTAL SPECIFICATIONS ....................................................................... 53 13. WARRANTEE AND SUPPORT INFO ......
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 4 1. INTRODUCTION The GigMAC and GigPMC-switch family of network adapter cards and switches are a.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 5 IEEE 802.3 (all sections applicable to 1000 Base T, 1000 Base SX , 1000 Base LX) IEEE 802.1D and IEEE 802.1Q as applicable for VLAN and priority queuing support PCI 2.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 6 3. KEY FEATURES The GigMAC (PMC and PCI), Gi gPMC-switch and GigPCI-E swit ches offer the following key features: • Sustained throughput of 245 Mbytes/sec (1.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 7 • Compatible with all 10/100/1000Ba seT hubs, switches and routers • Burst rate of up to 256 dwor ds (1024 bytes) over PCI bus • Jumbo frame support for up to 9K, 802.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 8 Driver Utilities (Linux) High-performance frame generator (wire and bus-speed capable) .
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 9 5. SYSTEM REQUIREMENTS Intel Platform (minimum) : Pentium III 800 MHZ or fast er with PC100 or PC133 SDRAM, 32-bit 33 MHZ PCI . Intel Platform (recommended) : Pentium4, Core Duo or Xeon at 1.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 10 6. HARDWARE INFORMATION 6.1 BOARD PHOTOS Model 5164 - 4-port PMC Model 5468 GigPMC 8-port sw i.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 11 Model 6468-RJ PCIe Model 5262-SC Model 5264-RJ Model 5263-SFP.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 12 6.2 BOARD LED INDICATORS PCI / PMC Boards LED Function Table Gigabit NIC Model LED # 1 Green L.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 13 LED_TX (transmit activity) LED_RX (receive activity) Model 5262-LC dual-port or 5261-L.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 14 The front panel has four onboard RJ-45 conn ectors that support the connection of Category 5e .
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 15 6.3 PMC CONNECTOR PIN/SIGNAL DEFINITIONS PMC Connectors Pin Assignments Pn1/Jn1 32 Bit PCI 1 T.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 16 Pn2/Jn2 32 Bit PCI 1 NC +12V TRST# 2 3 TMS TDO 4 5 TDI GND 6 7 GND PCI-RSVD NC 8 9 NC PCI-RSVD PCI-RSVD NC 10 11 NC BUSMODE2# +3.3V 12 13 RST# BUSMODE3# PMC_1 14 15 3.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 17 Pn3/Jn3 32 Bit PCI 1 NC PCI-RSVD GND 2 3 GND C/BE[7]# 4 5 C/BE[6]# C/BE[5]# 6 7 C/BE[4]# GND 8.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 18 Pn4/Jn4 (optional I/O – Model 5468 only) 1 NC I/O I/O NC 2 3 NC I/O I/O NC 4 5 NC I/O I/O NC.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 19 6.4 PCI CONFIGURATION REGISTERS in: unit: 0, bus: 16, dev: 1, func: 0, pci regs: device&ve.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 20 6.4.1 VENDOR AND DEVICE IDS All Intel based models use the 82546GB chip which has the following vendor and device ID: Vendor ID: 8086 Device ID: 1010 6.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 21 Model 5262-RJ in: unit: 0, i82546 serial eeprom cfg: eeprom[0x00]: 5000 eeprom[0x01]: 0cc2 eep.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 22 6.6 DEFAULT REGISTER SETTINGS The following lists the default register setti ngs for the Intel.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 23 The following lists the default register setti ngs for the Intel 82546 Gigabit controller on t.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 24 6.7 ETHERNET FRAME LATENCY The following table shows typical system le vel frame latencies me .
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 25 generate static. If you must leave the inst allation area before the installation is complete, be sure to ground yourself agai n before continuing the installation.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 26 Step 2 – Remove the CompactPCI or Embedded Mainboard controller from the system, if necessary to access the PMC slot. This wil l allow the PMC adapter card to be more easily installed.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 27 Connecting Fiber optic Model 6267-SFP, 5261-LC, 5262-LC, 5263-SFP This section explains how to connect the fi ber cards to the external network using standard fiber optic cables.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 28 RJ-45 pinouts for CAT5 connectors and cabl es are shown in the follow ing table: Pin 10/100 Si.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 29 $ mkdir util $ cd util $ cp /mnt/cdrom/linux-dpm-driver/util/util*.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 30 TYPE=Ethernet USERCTL=no NETMASK=255.255.255.0 NETWORK=192.168.0.0 BROADCAST=192.168.0.255 Note: You should also add a line to /etc/modules.conf for each interface as shown in the following example: SAMPLE MODULES.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 31 TUNING THE INSTALLATION Interrupt holdoff (programmed latency) To increase (or decrease) the value of the programmed interrupt latency, insert the module and set the "IntrHold Off" parameter as follows: insmod .
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 32 ‘Insmod’ Command Line Parameters The following parameters are used by ent ering them on the command line with the modprobe or insmod command.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 33 to receive all unicast frames (sometimes useful in frame generator testing). Do not enable for normal traffic. ChipSelector 0, 1 1 Sets the chip set sel ector (0=National, 1=Intel).
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 34 dmUtil -m eth0 # displays DP83820 MAC controller registers dmUtil -p eth0 # displays gigabit (.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 35 Using dmUtil dpm driver utility: The “dpm driver utility” is used to capture detailed board levels statistics, controller registers and to set loopback mode.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 36 10.3 DRIVER UTILITY COMMAND REFERENCE 10.3.1 STATISTICS SHOW FUNCTION vxWorks usage: inShow(unit) # unit = device index starting from 0 Linux usage: .
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 37 10.3.2 PCI REGISTERS SHOW FUNCTION vxWorks usage: inShowPciRegs(unit) # unit = device index st.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 38 10.3.3 MAC REGISTERS SHOW FUNCTION vxWorks usage: inShowMacRegs(unit) # unit = device index starting from 0 Linux usage: ./dmUtil –m eth1 # eth1, eth2, etc.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 39 10.3.4 MAC STATISTICS SHOW FUNCTION vxWorks usage: inShowMacStats(unit) # unit = device index starting from 0 Linux usage: ./dmUtil –ms eth1 # eth1, eth2, etc.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 40 NODEF: (0x40c4): 27 NODEF: (0x40c8): 3384703584 NODEF: (0x40cc): 27 NODEF: (0x40d0): 79354269 .
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 41 10.3.5 PHY REGISTERS SHOW FUNCTION vxWorks usage: inShowPhyRegs(unit) # unit = device index starting from 0 Linux usage: ./dmUtil –p eth1 # eth1, eth2, etc.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 42 10.3.6 EEPROM SHOW FUNCTION vxWorks usage: inShowEeprom(unit) # unit = device index starting from 0 Linux usage: ./dmUtil –e eth1 # eth1, eth2, etc.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 43 10.3.7 MAC ADDRESS SHOW FUNCTION vxWorks usage: inShowMacAddr(unit) # unit = device index starting from 0 Linux usage: ./dmUtil –a eth1 # eth1, eth2, etc.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 44 10.3.9 STARTING FRAME GENERATOR vxWorks usage: inStrtFrmGen(unit, frmSize) # unit = device index starting from 0 Linux usage: ./dmUtil –l eth1 1 # eth1, eth2, etc.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 45 10.3.11 SWITCH STATUS SHOW FUNCTION Note: This function is applicable fo r Model 5468 GigPMC and Model 6468 GigPCIe switch/interface cards only. vxWorks usage: inShowSwitch(unit) # unit = device index starting from 0 Linux usage: .
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 46 A. Opening a socket for management API int s; s = socket (PF_INET, SOCK_STREAM, 0); B.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 47 /* get driver trace buffer */ #define DM_IOCTL_GET_TRC 1 /* get driver statistics */ #define D.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 48 Functions to read and write registers in the switch: STATUS inReadSpiReg(int unit, int page, i.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 49 11. TESTING AND VERIFICATION There are several ways to test your adapt er on vxWorks and Linux platforms. This section provides suggestions on how you may test and veri fy your installation.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 50 12. SPECIFICATIONS Connector (Models 5261-RJ, 5262-RJ, 5164, 5264, 5468, 6162, 6468, 6267-RJ):.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 51 Burst Rate: Up to 256 dwords (1024 bytes) over PCI bus Host Offloading: IPv.4 checksum (UDP, TCP and IP) and optional statistics gathering for RFC 1213 (MIB II), RFC 1398 (Ether-like MIB), IEEE 802.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 52 IEEE 802.3z Gigabit Ethernet ov er 1000 Base SX multimode fiber IEEE 802.1D and 802.1Q as applicable for VLAN priority queuing IEEE 802.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 53 12.1 ENVIRONMENTAL SPECIFICATIONS Rugged Class Grade Operating Temp.
GigMAC-PMC and PCI GigPMC Switch Board and Driver Users Man u al DSS NETWORKS, INC. Version: 2.6 Page: 54 13. WARRANTEE AND SUPPORT INFO Technical Support and Warranty: Telephone technical support (Mo.
Een belangrijk punt na aankoop van elk apparaat Intel PCI-X (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Intel PCI-X heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Intel PCI-X vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Intel PCI-X leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Intel PCI-X krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Intel PCI-X bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Intel PCI-X kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Intel PCI-X . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
