Gebruiksaanwijzing /service van het product PRO/100 van de fabrikant Intel
Ga naar pagina of 38
i ENet2.book Page i Monday, May 4, 1998 9:53 AM.
ii I ntel EtherExpress PRO/100+ TX PCI LAN Controller User’s Guide Notices Copyrigh t © 1998 Gateway 2000, Inc. All Rights Reserved 610 Gateway Drive N. Sioux C ity , SD 57049 U SA All Rights Reser ved This publicati on is protected b y cop yright an d all righ ts are reser ved.
iii Contents Introduction................................................................ .............................. 1 Connect the Network Cable ...................................... .............................. 2 Configure the Contr oller and Install Drivers .
iv Gateway ALR 8200 Rack Mount User’s Guide ENet2.book Page iv Monday, May 4, 1998 9:53 AM.
Introduction 1 Intr oduction The OnBoard Ethernet Controller ( O BEC) is an In tel 82558 ethernet controller device and ma y be detected b y softw are as either and Int el EtherExpress PR O/ 100+ or an Intel 82558 ethernet controller . The OBEC ma y be enabl ed or disable d through the BIOS Setup utility .
2 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide Connect t he Netw ork Cab le 1. Connect a single n etw ork cabl e to the ethernet port as sho wn belo w . F or 100B ASE-TX, y our netw ork cab le must be Category 5, twisted- pair wiring.
Configure the Controller and Install Drivers 3 Configur e the Contr oller and Instal l Drivers Windows 95 A utomatic Configuration This PCI computer automat ically detects and conf igures the onboard PCI- compliant ethernet contr oller . The BIOS auto maticall y sets the control ler’ s IRQ le vel and I/O addre ss.
4 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide Install the PROSet Softw are (Op tional) PR OSet is a n enhanced utility y ou can use to easil y conf igure and test y our OBEC in W indo ws 95. PR OSet also displ ays the computer resources tha t are assigned t o each adapter y ou install.
Configure the Controller and Install Drivers 5 6. Select Netw ork Ada pters and click OK. 7. Click Ha ve Disk. I nser t the Conf iguration and Dri vers disk an d click OK. 8. F oll ow any prompts f or W indo ws 95 installati on disks and restart w hen prompted.
6 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide Install Networ k Dr iv ers - Wind o ws NT V ersion 4.0 Only After enab ling the ehternet controller in the computer and starting W indo w s NT , you need to ins tall the correct driv ers.
Configure the Controller and Install Drivers 7 Install Networ k Dr iv ers - Wind o ws NT V ersion 3.51 Only After enab ling the OBEC in the computer a nd star ting W indo ws NT , you need to in stall the correct driv ers and test the controller . 1. Doub le-click the Netw or k icon in the Control P anel.
8 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide • Check the W indo ws NT Eve nt V iew er for er ror messages. • If y ou are attachin g to a NetW are netw ork, check y our frame type and v erify that NetW are client softw are has been installe d.
Configure the Controller and Install Drivers 9 2. Insert the Conf igurat ion and Driv ers disk in a fl opp y driv e, swi tch to that dri ve, and at the DOS prompt, type SETUP E NTER 3. If y ou hav e more than one PCI adapte r in your computer , an adapter selection menu app ears on the screen.
10 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide • T est the adapter b y r unning di agnostics in Setup. Additional t esting is a v ailab le by using a responder (see t he next section) .
Installing Multiple Adapters 11 Instal ling Multiple Adapter s All users: The system’ s 12-digit, he xadecimal Ether net address is printed on a stick er placed on the system board. The Ether net address is so metimes called the node address or the MA C address.
12 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide Select Duple x Mode (Optional) Duplex ing is a performance option that l ets you choose ho w the ethernet controller sends and recei ves dat a packets o v er the netw ork.
Select Duplex Mode (Optional) 13 DOS ODI, NDIS 2.01 Clients Edit the NET .CFG or PR O T OCOL.INI f ile. Add these keyw ords t o the Link Dri ver s ection: FORCEDUPLEX 2 SPEED 100 (or 10 if 10B ASE-T) NetW are Ser ver In A UT OEXEC.
14 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide Windows 95 1. In the Control P anel, doub le-click the Sys tem icon. 2. Go to the De vice Manager tab and sele ct the controller . 3. Click Properties, then click OK to use the setup pro g ram (PR OSet).
Choose Ethernet Controller Teaming Options 15 Choose Ethernet Co ntr oller T eaming Options The onboard PR O/100+ et her net control ler pro vides se ver al options for increasing t hroughput and fault tolerance when running W indo ws NT 4.0 or NetW are 4.
16 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide T o use Adapter F ault T olerance, y ou must ha ve at least tw o PR O/100+ adapters inst alled in yo ur W indo ws NT 4.0 or NetW are 4.x w orkstation or server and the y must be link ed to the same netw ork.
Choose Ethernet Controller Teaming Options 17 Setting up Adapter F ault T olerance in NetW are 1. Cop y the follo wing li nes from the EXAMPLES.TXT f ile (on the Conf iguration and Dri ve rs disk) and paste them int o the appropriate f iles. These commands assume the AFT .
18 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide 2. Modify the lines t o match your wor kstation or server’ s requirements. 3. Sa ve the ST AR TUP .NCF and A UT OEXEC.NCF f iles and rest ar t your server . Deleting a T eam T o remo ve a team in AFT , ALB or FEC mode, edit out t he lines abo v e.
Choose Ethernet Controller Teaming Options 19 4. Click OK w hen prompted. Y ou’ ll see the Adapter T eaming Conf iguration windo w . 5. F oll ow the instr uctions to ass ign adapters to a team. ALB supports up to tw o adapte r teams, with t w o, three, or four adapter s per team.
20 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide Cop y these lines into t he A UT OEXEC.NCF f ile ;- Load LAN driver on 1st controller load e100b slot=7 frame=ethernet_802.2 name=pri_802.2 ;- Load LAN driver on 2nd adapter load e100b slot=8 frame=ethernet_802.
Choose Ethernet Controller Teaming Options 21 Setting -Up F ast EtherChannel F ast EtherChannel (FEC) is a performance technolo g y dev eloped b y Cisco to increase y our w orkstation or ser ver ’ s throughput .
22 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide Deleting a T eam 1. Doub le-click the Netw or k icon in the Control P anel. 2. On the Adapters tab, s elect the FEC team to delete . 3. Click Remo ve. Y ou’ ll see a c onf ir mation dialo g.
Choose Ethernet Controller Teaming Options 23 Where: slot= the slot in which your PR O/100+ adapter i s installed , such as 7. If y ou don’ t kno w the number , load t he driv er without it. NetW are will prompt y ou with a vai lable PCI de vice numbers.
24 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide T r oublesh ooting and F A Qs If the OnBoard Ether ne t Control ler Can’t Connect to the Network Make Sure the Cab le i s Installed Proper ly The netw ork cab le must be s ecurely at tached at both RJ-45 connect ions (controlle r and hub).
Troubleshooting and FAQs 25 Make Sure Y ou are Using the Cor rect Drivers Make sure y ou’ re usi ng the dri vers that come with this compute r . The driv er f ile name contai ns the letter B (for e xample, E100BODI.
26 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide F requently Ask ed Questions (F A Qs) SETUP .EXE r epor ts the controller is “Not enabled b y BIOS”. • The PCI BIOS is not conf iguring the contr oller cor rectly . T r y “PCI Installat ion Ti ps” on page 28.
Troubleshooting and FAQs 27 The controller stopped working when another adapter was added to the computer . • Make sure the cable i s connected to the contr oller . • Make sur e your PCI BIOS is current. See “PCI Installat ion Ti ps” on page 28.
28 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide T echni cal Info rmation PCI Installation Tips PCI computers a re designed to automatical ly conf igure add-in cards each time the computer s tar ts. Y our PCI computer sets the I/ O address and IRQ le vel for your netw or k controller w hen the computer starts.
Technical Information 29 • Conf igure the slot for le vel-tri ggered inter rupts. The slot the controller is using must be conf igured for le vel-t riggered inter rupts rather than e dge-triggere d inter r upts. Check y our PCI BIOS Setup pro g ram.
30 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide Shared hubs In a shared net work e n vironment, computers are c onnected to hubs called repeaters. All por ts of the repeate r hub share a f ix ed amount of bandwidth, or data capaci ty .
Network Software License Agreement 31 Netw ork Softwa re Licens e Agreement PLEASE R EVIEW THE LICENSE AGREEME NT BELO W . BY OPENI NG THIS SOFT W ARE OR P ACKA GE OR O THER WISE DO WNLO ADING OR COPYING T HIS SOFTW ARE, Y OU AR E A GREEING T O BE BOUND BY THE TER MS OF T HIS AGREEMENT .
32 Intel EtherExpress PRO/100+ TX PCI LAN Controll er User’s Guide EXPOR T LA WS: Y ou agree that the distribution and export/re-export of the Softwar e is in compliance with the la ws, regulatio ns, orders or other restrictions of the U .S. Expor t Administration Regulation s.
NO TES ENet2.book Page xxxiii Monday, May 4, 1998 9:53 AM.
8503060 -- R0 ENet2.book Page xxxiv Monday, May 4, 1998 9:53 AM.
Een belangrijk punt na aankoop van elk apparaat Intel PRO/100 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Intel PRO/100 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Intel PRO/100 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Intel PRO/100 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Intel PRO/100 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Intel PRO/100 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Intel PRO/100 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Intel PRO/100 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
