Gebruiksaanwijzing /service van het product System Board G4H875-B van de fabrikant Intel
Ga naar pagina of 124
935-G4H875-000 A77100333 G4H875-N G4H875-C G4H875-B Re v . A+ System Board User’ s Man ual.
Cop yright This publication contains information that is protected by copyright. No par t of it may be reproduced in an y form or by an y means or used to make any transformation/adaptation without the prior wr itten permission from the copyr ight holder s.
Batter y: • Danger of explosion if batter y incor rectl y replaced. • Replace only with the same or equivalent type recommend by the manufacturer .
Notice An electronic f ile of this manual is included in the CD . T o view the user’ s man ual, inser t the CD into a CD-ROM drive . The autor un screen (Main Board Utility CD) will appear .
T able of Contents Chapter 1 - Introduction 1.1 Features and Specifications.................................................................................. 1.2 Hyper -Threading T echnology Functionality Requirements..... 1. 3 Package Checklist......
Introduction 1 6 Appendix A - Enabling the Hyper -Thr eading T echnolog y A .1 Enabling the Hyper -Threading T echnology ......................................... Appendix B - CPU Fan Protection B .1 CPU Fan Protection.................................
1 Introduction 7 1.1 Features and Specifications 1.1.1 Features Chipset • Intel ® 875P chipset - Intel ® 82875P Memor y Controller Hub (MCH) - Intel ® Hance Rapids I/O Controller Hub Processor The system board is equipped with Socket 478 for installing one of the following suppor ted processor s.
Introduction 1 8 Perf ormance Acceleration T echnology (P A T) P A T mode is suppor ted onl y when the system uses DDR400 with 800MHz FSB CPU . P A T perf or ms data transactions directly from the CPU to the system memor y , b ypassing the normal path of oper ation.
1 Introduction 9 Onboard Audio Features • 18-bit stereo full-duplex codec with independent variable sam- pling rate • High quality differential CD input • T r ue stereo line lev el outputs • 2.
Introduction 1 10 USB Ports The system board suppor ts USB 2.0 and USB 1.1 por ts. USB 1.1 suppor ts 12Mb/second bandwidth while USB 2.0 suppor ts 480Mb/second bandwidth providing a mar ked impro vement in device transfer speeds between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
1 Introduction 11 I/O Connectors • 1 connector for 2 additional external USB 2.0/1.1 por ts (G4H875-B only) • 2 connector s for 2 exter nal ser ial por ts (G4H875-N only) • 1 front audio connect.
Introduction 1 12 1.1.3 Intelligence CPU Fan Protection The CPU Fan Protection function has the capability of monitoring the CPU fan when the system boots. Once it has detected that the CPU fan did not rotate, 5 warning beeps will sound then the system will automatically po wer -off.
1 Introduction 13 W a k e-On-LAN This feature allo ws the networ k to remotel y wake up a Soft P ow er Down (Soft-Off) PC . It is suppor ted via the onboard LAN por t, via a PCI LAN card that uses the PCI PME (P ow er Management Event) signal or via a LAN card that uses the W ake-On-LAN connector .
Introduction 1 14 A CPI The system board is designed to meet the A CPI (Advanced Con- figuration and P ower Interface) specif ication. A CPI has ener gy sa ving features that enab les PCs to implement P ow er Management and Plug-and-Play with operating systems that suppor t OS Direct P ower Management.
1 Introduction 15 1. 2 Hyper -Thr eading T echnolog y Functionality Requirements Enabling the functionality of Hyper -Threading T echnology for y our computer system requires ALL of the follo wing platforms.
16 2 Hardware Installation 2.1 System Board La y out Chapter 2 - Hardware Installation G4H875-N KB/Mouse COM 1 COM 2 Parallel LAN 1; USB 1-2 Intel Gigabit 82547EI Intel 82551QM Line-out Line-in Mic-in.
17 2 Hardware Installation KB/Mouse COM 1 COM 2 Parallel LAN; USB 1-2 Intel 82551QM Line-out Line-in Mic-in USB 3-4 Sock et 478 1 PS/2 KB/Mouse power select (JP2) 1 USB 1-4 power select (JP3) Intel 82.
18 2 Hardware Installation G4H875-B Note: The illustrations on the following pages are based on the G4H875-N system board. KB/Mouse COM 1 COM 2 Parallel LAN 1; USB 1-2 Intel 82551QM Line-out Line-in M.
19 2 Hardware Installation 2 1 ON 2.2 System Memor y W arning: Electrostatic discharge (ESD) can damage your system board, processor , disk dr ives , add-in boards , and other components. P erf or m the upgrade instruction procedures described at an ESD workstation only .
20 2 Hardware Installation The system board suppor ts the follo wing memor y interface . Single Channel (SC) Data will be accessed in chunks of 64 bits (8B) from the memor y channels. Virtual Single Channel (VSC) If both channels are populated with different memor y configur ations, the MCH defaults to Vir tual Single Channel.
21 2 Hardware Installation The table below lists the various optimal operating modes that should be conf igured f or the memor y channel operation. Config No memor y Single channel A Single channel A .
22 2 Hardware Installation Config Dynamic Mode Addressing Dynamic Mode Addressing Dynamic Mode Addressing Dynamic Mode Addressing Dynamic Mode Addressing Dynamic Mode Addressing DDR 1 E P(*)(1,3) DS P.
23 2 Hardware Installation 2.2.1 Installing the DIM Module A DIM module simply snaps into a DIMM socket on the system board. Pin 1 of the DIM module must correspond with Pin 1 of the socket. 1 . Pull the “tabs” which are at the ends of the socket to the side.
24 2 Hardware Installation 2.3 CPU 2.3.1 Ove r vie w The system board is equipped with a surface mount 478-pin CPU socket. This sock et is exclusiv ely designed f or installing an Intel processor . 2.3.2 Installing the CPU 1 . Locate Socket 478 on the system board.
25 2 Hardware Installation 3 . P osition the CPU abov e the socket then align the gold mar k on the corner of the CPU (designated as pin 1) with pin 1 of the socket. Important: Handle the CPU by its edges and avoid touching the pins. Gold mar k 4. Inser t the CPU into the socket until it is seated in place .
26 2 Hardware Installation 5. Once the CPU is in place, push down the lever to lock the socket. The lever should click on the side tab to indicate that the CPU is completely secured in the socket. 2.3.3 Installing the Fan and Heat Sink The CPU must be kept cool by using a CPU fan with heatsink.
27 2 Hardware Installation 1. The system board comes with the retention module base already installed. Retention module base Retention hole Retention hole Retention hole Retention hole 2.
28 2 Hardware Installation 3. The retention lever s at this time remains unlocked as sho wn in the illustration below . Retention lever Retention lever 4. Mov e the retention lev er s to their opposite directions then push them down. This will secure the fan / heat sink and retention mechanism assembly to the retention module base.
29 2 Hardware Installation 2 1 O N 2.4 Jumper Settings 2.4.1 Clearing CMOS Data If you encounter the following, a) CMOS data becomes corrupted. b ) Y ou forgot the super visor or user password. c ) Y ou are unable to boot-up the computer system because the processor’s ratio/clock was incorrectly set in the BIOS.
30 2 Hardware Installation 4 . After powering-on the system, press <Del> to enter the main menu of the BIOS. 5 . Select the Frequency/V oltage Control submenu and press <Enter>. 6 . Set the “CPU Clock Ratio” or “CPU Clock” f ield to its default setting or an appropriate bus clock or frequency ratio.
31 2 Hardware Installation 2 1 ON 2.4.2 PS/2 K eyboar d/Mouse W ak e Up ! JP2 2-3 On: 5VSB 1-2 On: VCC (default) 3 1 2 3 1 2 This jumper is used to select the power of the PS/2 Keyboard/ Mouse por t. Selecting 5VSB will allo w y ou to use the W ak e-On- PS/2 Keyboard/Mouse function.
32 2 Hardware Installation 2 1 ON 2.4.3 USB K eyboar d W ak e Up These jumper s are used to select the power of the USB por ts. Selecting 5VSB will allow y ou to use the W ake-On-USB Key- board function. On the G4H875-N and G4H875-C system boards, JP3 is for setting USB 1-4 that are at the rear I/O panel.
33 2 Hardware Installation 2 1 O N 2.4.4 P o w e r -on Select ! 1-2 On: Power-on via power button (default) 3 1 2 3 1 2 JP6 2-3 On: Power-on via AC power This jumper is used to select the method of powering on the system. If you want the system to po wer -on once A C pow er comes in, set JP6 pins 2 and 3 to On.
34 2 Hardware Installation SW1 is used to conf igure the BIOS Wr ite Protect function. When this function is enabled, the system will be protected from unneces- sar y updating or flashing of the BIOS. It secures the BIOS theref ore any updates to it will not take effect.
35 2 Hardware Installation 2.5 Rear Panel I/O Ports PS/2 K/B COM 1 USB 1-2 USB 3-4 COM 2 PS/2 Mouse LAN 2 Parallel LAN 1 Line-out Line-in Mic-in G4H875-N PS/2 K/B COM 1 USB 1-2 COM 2 PS/2 Mouse Parall.
36 2 Hardware Installation 2 1 O N 2.5.1 PS/2 Mouse and PS/2 K eyboard P or ts The system board is equipped with an onboard PS/2 mouse (Green) and PS/2 keyboard (Pur ple) por ts - both at location CN1 of the system board. The PS/2 mouse por t uses IRQ12.
37 2 Hardware Installation 2 1 ON COM 1 COM 2 2.5.2 Serial Ports " G4H875-N is equipped with 2 onboard ser ial por ts (COM 1: CN3 and COM 2: CN4) - both in T eal/T urquoise color . It is also equipped with two 9-pin connector s (COM 3: J14 and COM 4: J16) for connecting exter nal serial por ts.
38 2 Hardware Installation 2 1 ON 2.5.3 Parallel Port The system board has a standard par allel por t (Burgundy) at location CN7 for interfacing y our PC to a par allel pr inter .
39 2 Hardware Installation 2 1 ON 2.5.4 Universal Serial Bus Ports The system board suppor ts USB 2.0/1.1 por ts. USB allows data exchange between your computer and a wide range of simulta- neously accessible external Plug and Play peripherals. G4H875-N and G4H875-C are each equipped with four onboard USB 2.
40 2 Hardware Installation BIOS Setting Configure USB in the Integrated P e ripher als submenu (“Onboard Device” section) of the BIOS. Refer to chapter 3 for more informa- tion. Driver Installation Y ou may need to install the proper dr ivers in your oper ating system to use the USB device .
41 2 Hardware Installation 2.5.5 RJ45 LAN Port G4H875-N is equipped with 2 onboard RJ45 LAN por ts. LAN 1 which is controlled by the Intel 82551QM chip is at location CN6 and LAN 2 which is controlled by the Intel Gigabit 82547EI chip is at location CN5.
42 2 Hardware Installation 2 1 ON Line-out Line-in Mic-in " 2.5.6 Audio " Front audio Mic-in, Line-in and Line-out The mic-in, line-in and line-out jacks are at location CN2 of the system board. A jack is a one-hole connecting interface for inser t- ing a plug.
43 2 Hardware Installation The front audio is disabled. The rear audio is enabled. The front audio is enabled. The rear audio is disabled. Pins 5-6 and 9-10 shor t (default) Pins 5-6 and 9-10 open Fr ont Audio The front audio connector (J3) allows you to connect to the line-out and mic-in jacks that are at the front panel of your sys- tem.
44 2 Hardware Installation 2 1 O N 2.6 I/O Connectors 2.6.1 Game/MIDI Port The system board is equipped with a 15-pin connector at loca- tion J2 for connecting an external game/MIDI por t.
45 2 Hardware Installation 2 1 O N 2.6.2 Internal Audio Connectors The CD-in (J1) and AUX-in (J4) connector s are use d to receive audio from a CD-ROM drive, TV tuner or MPEG card.
46 2 Hardware Installation 2 1 ON 2.6.3 S/PDIF Connector " The S/PDIF connector (J5) is used to connect external S/PDIF por ts. The S/PDIF por ts may be mounted on a card-edge bracket. Install the card-edge bracket to the system chassis then connect the audio cable connector to J5.
47 2 Hardware Installation 2 1 O N 2.6.4 Flopp y Disk Driv e Connector The system board is equipped with a shrouded floppy disk drive connector f or connecting a standard floppy disk drive . T o prev ent improper floppy cable installation, the shrouded floppy disk header has a keying mechanism.
48 2 Hardware Installation 2 1 ON 2.6.5 Serial A T A Connectors Connect one end of the SA T A cab le to J22 (SA T A 2) or J23 (SA T A 1) and the other end to your serial A T A device . BIOS Setting Configure the Serial A T A dr ives in the Integrated P er ipher als submenu (“OnChip IDE Device” section) of the BIOS.
49 2 Hardware Installation 2 1 O N 2.6.6 IDE Disk Drive Connector The system board is equipped with two shrouded PCI IDE header s that will interface four Enhanced IDE (Integrated Drive Electronics) disk dr iv es. T o prevent improper IDE cab le installation, each shrouded PCI IDE header has a keying mechanism.
50 2 Hardware Installation Note: Refer to your disk drive user’s manual for information about selecting proper drive switch settings. Adding a Second IDE Disk Drive When using two IDE drives, one must be set as the master and the other as the slav e .
51 2 Hardware Installation 2 1 ON 2.6.7 IrD A Connector Connect y our IrD A cable to connector J7 on the system board. Note: The sequence of the pin functions on some IrDA cable may be reversed from the pin function defined on the system board. Make sure to connect the cable to the IrDA connector according to their pin functions.
52 2 Hardware Installation 2 1 O N ! 2.6.8 Cooling Fan Connectors Connect the CPU fan’ s cable connector to the CPU fan connec- tor (J13) on the system board. Connect the Intel 875P fan’ s cable connector to the NB fan connector (J27) on the system board.
53 2 Hardware Installation 2 1 ON 2.6.9 W a k e-On-LAN Connector Y our LAN card package should include a cab le . Connect one end of the cable to the wakeup header on the card and the other end to location J10 on the system board. The netw or k will detect Magic Pa ck et and asser t a wak e up signal to po wer -up the system.
54 2 Hardware Installation 2 1 ON 2.6.10 Chassis Open Connector 2 1 Ground Chassis signal " The system board suppor ts the chassis intr usion detection func- tion. T o use this function, connect the chassis intr usion sensor cable from the chassis to J6.
55 2 Hardware Installation 2 1 ON 2.6.11 LEDs DIMM Standby Power LED This LED will tur n red when the system’ s pow er is on or when it is in the Suspend state (P ow er On Suspend or Suspend to RAM). It will not light when the system is in the Soft-Off state.
56 2 Hardware Installation Ear ly progr am chipset reg- ister before POST . T esting memor y presence . Detecting memor y siz e . No memor y present. Programming DRAM tim- ing register . Calculating DRAM size var iab le including row , col- umn and bank.
57 2 Hardware Installation 2 1 ON 2.6.12 Power Connectors W e recommend that y ou use a pow er supply that complies with the A TX12V P ower Suppl y Design Guide V er sion 1.1. An A TX12V po wer supply has a standard 20-pin A TX main power connector and a 4-pin +12V pow er connector that m ust be inser ted onto CN9 and CN8 connector s respectively .
58 2 Hardware Installation 2 1 ON 2.6.13 Front Panel Connectors HD-LED: Primary/Secondary IDE LED This LED will light when the hard drive is being accessed. RESET: Reset Switch This switch allows you to reboot without having to power off the system thus prolonging the life of the power supply or system.
59 2 Hardware Installation PWR-LED: Power/Standby LED When the system’ s power is on, this LED will light. When the system is in the S1 (POS - P ow er On Suspend) state , it will blink ever y second. When the system is in the S3 (STR - Suspend T o RAM) state , it will blink ever y second.
60 3 BIOS Setup 3.1 A war d BIOS Setup Utility The Basic Input/Output System (BIOS) is a program that takes care of the basic level of communication between the processor and peripherals. In addition, the BIOS also contains codes for various advanced features f ound in this system board.
61 3 BIOS Setup The settings on the screen are for reference onl y . Y our ver sion may not be identical to this one. 3.1.1.1 Date The date format is <day>, <month>, <date>, <year>. Day displays a day , from Sunday to Saturda y .
62 3 BIOS Setup The settings on the screen are for reference onl y . Y our ver sion may not be identical to this one. IDE HDD Auto Detection Detects the par ameter s of the dr ive.
63 3 BIOS Setup Capacity Displays the approximate capacity of the disk drive. Usually the size is slightly greater than the size of a formatted disk given by a disk checking program. Cylinder This field displa ys the n umber of cylinder s. Head This field displays the number of read/write heads.
64 3 BIOS Setup 3.1.1.5 Video This field selects the type of video adapter used f or the pr imar y system monitor . Although secondar y monitor s are suppor ted, you do not hav e to select the type . The default setting is EGA/V GA. EGA/VGA Enhanced Gr aphics Adapter/Video Gr aphics Ar ray .
65 3 BIOS Setup 3.1.1.8 Extended Memory Displays the amount of extended memor y detected dur ing boot-up . 3.1.1.9 T otal Memory Displays the total memor y availab le in the system.
66 3 BIOS Setup 3.1.2 Advanced BIOS F eatures The Advanced BIOS Features allows y ou to conf igure y our system for basic operation. Some entries are defaults required by the system board, while other s, if enab led, will impro v e the perfor mance of y our system or let you set some features according to your preference.
67 3 BIOS Setup 3.1.2.4 CPU L3 Cache This f ield is used to enable or disab le the CPU’ s L3 cache . 3.1.2.5 Hyper -Threading T echnolog y (for Intel ® P entium ® 4 Pr ocessor with Hyper -Threadin.
68 3 BIOS Setup 3.1.2.10 Gate A20 Option This entr y allows y ou to select how gate A20 is handled. Gate A20 is a device used to address memor y above 1 Mbyte.
69 3 BIOS Setup 3.1.2.14 Security Option This field determines when the system will prompt for the password - ever ytime the system boots or only when you enter the BIOS setup.
70 3 BIOS Setup 3.1.3 Advanced Chipset F eatur es This section gives you functions to configure the system based on the specif ic features of the chipset. The chipset manages bus speeds and access to system memor y resources. These items should not be alter ed unless necessar y .
71 3 BIOS Setup Manual If y ou want y our system to r un at a perfor mance better than the one “by SPD”, select “Manual” then select the best option in the “C AS Latency Time” to “DRAM RAS# Precharge” fields. 3.1.3.2 C AS Latency Time This field is used to select the local memor y clock per iods.
72 3 BIOS Setup 3.1.3.8 System BIOS Cacheable When this field is enabled, accesses to the system BIOS ROM addressed at F0000H-FFFFFH are cached, provided that the cache controller is enabled. The lar ger the range of the Cache RAM, the higher the efficiency of the system.
73 3 BIOS Setup 3.1.3.13 DRAM Data Integrity Mode The ECC (Er ror Checking and Correction) function is suppor ted only in x72 (72-bit) PC SDRAM DIMMs. If you are using x64 (64-bit) PC SDRAM DIMMs, set this field to Non-ECC . Non-ECC Uses x64 PC SDRAM DIMM.
74 3 BIOS Setup 3.1.4 Integrated Peripherals The settings on the screen are for ref erence only . Y our ver sion ma y not be identical to this one. 3.1.4.1 OnChip IDE Device Mov e the cur sor to this f ield and press <Enter>. The following screen will appear .
75 3 BIOS Setup IDE HDD Block Mode Enabled The IDE HDD uses the block mode. The system BIOS will check the hard disk drive for the maximum block size the system can tr ansf er . The block siz e will depend on the type of hard disk drive. Disabled The IDE HDD uses the standard mode.
76 3 BIOS Setup IDE Primary Master/Slave UDMA and IDE Secondary Master/ Slave UDMA These fields allo w y ou to set the Ultra DMA in use . When Auto is selected, the BIOS will select the best available option after checking your hard drive or CD-ROM. Auto The BIOS will automatically detect the settings for you.
77 3 BIOS Setup 3.1.4.2 Onboard Device Mov e the cur sor to this f ield and press <Enter>. The follo wing screen will appear . The settings on the screen are for ref erence only . Y our version may not be identical to this one. USB Controller Enabled Enables the onboard USB.
78 3 BIOS Setup 3.1.4.3 Super IO Device Mov e the cur sor to this f ield and press <Enter>. The following screen will appear . The settings on the screen are for reference onl y . Y our v er sion ma y not be identical to this one. Power On Function This f ield allows y ou to use the keyboard or PS/2 mouse to pow er - on the system.
79 3 BIOS Setup Keyboard 98 When this option is selected, press the “wake up” key of the Windo ws 98 compatible k eyboard to power -on the system. KB Power On Password Mov e the cur sor to this field and press <Enter>. Enter your pass- word.
80 3 BIOS Setup RxD , TxD Active The options are Hi, Lo; Lo, Hi; Lo, Lo; and Hi, Hi. IR T ransmission Dela y If this f ield is Enabled, tr ansmission of data will be slow er . This is recommended when you encounter transmission problem with your device .
81 3 BIOS Setup If you selected EPP , the “EPP Mode Select” field is selectab le . If you selected ECP , the “ECP Mode Use DMA” field is selectab le . If you selected ECP+EPP , both “EPP Mode Select” and “ECP Mode Use DMA” are selectable.
82 3 BIOS Setup Onboard Serial Port 3 (G4H875-N only) This field is used to select the serial por t 3’ s I/O address. Onboard Serial Port 3 IRQ (G4H875-N only) This field is used to select the serial por t 3’ s IRQ address. This field is not configurable if the “Onboard Ser ial P or t 3” f ield is set to Disabled.
83 3 BIOS Setup 3.1.5 Power Management Setup The P ow er Management Setup allows y ou to configure y our system to most effectiv ely sa v e ener gy . 3.1.5.1 A CPI Function This function should be enabled only in operating systems that sup- por t A CPI.
84 3 BIOS Setup 3.1.5.3 Run V GABIOS if S3 Resume When this field is set to Auto, the system will initialize the V GA BIOS when it wakes up from the S3 state . This can be conf igured only if the “A CPI Suspend T ype” f ield is set to “S3(STR)”.
85 3 BIOS Setup 3.1.5.8 MODEM Use IRQ This field is used to set an IRQ channel for the modem installed in your system. 3.1.5.9 Suspend Mode This is selectable onl y when the P o w er Management field is set to User Define.
86 3 BIOS Setup 3.1.5.12 W ak e-Up b y PCI Car d Enabled This field should be set to Enabled only if your PCI card such as LAN card or modem card uses the PCI PME (P ow er Management Ev ent) signal to remotely wake up the system. Access to the LAN card or PCI card will cause the system to wake up.
87 3 BIOS Setup 3.1.5.17 Resume By Alarm Enabled When Enabled, you can set the date and time you would lik e the Soft P ower Down (Soft-Off) PC to po wer -on in the “Date (of Month) Alar m” and “Time (hh:mm:ss) Alarm” fields.
88 3 BIOS Setup 3.1.6 PnP/PCI Configurations This section descr ibes conf igur ing the PCI b us system. It co v er s some ver y technical items and it is strongly recommended that onl y exper ienced user s should mak e any changes to the default settings.
89 3 BIOS Setup 3.1.6.3 IRQ Resources Mo v e the cur sor to this field and press <Enter>. The “IRQ-3” to “IRQ-15” f ields will appear . Set each system inter r upt to either PCI Device or Reser ved. 3.1.6.4 PCI/V GA Palette Snoop This f ield deter mines whether the MPEG ISA/VESA V GA cards can wor k with PCI/V GA or not.
90 3 BIOS Setup 3.1.7 PC Health Status 3.1.7.1 Shutdown T emperatur e Y ou can prevent the system from o v erheating by selecting a tem- perature in this field. If the system detected that its temperature exceeded the one set in this field, it will automatically shutdown.
91 3 BIOS Setup 3.1.7.4 VCC3(V), +12(V), -12(V), VCC(V), VB A T(V) and 5VSB(V) These fields sho w the output v oltage of the pow er suppl y . Note: The onboard hardware monitor function is capable of .
92 3 BIOS Setup 3.1.8 Frequency/V oltage Contr ol The settings on the screen are for reference onl y . Y our ver sion may not be identical to this one. 3.1.8.1 CPU Clock Ratio This field is used to select the CPU’ s frequency r atio . Important: The frequency ratio of some processors may have been locked by the manuf acturer .
93 3 BIOS Setup 3.1.8.5 CPU Clock This field provides several options for selecting the external system bus clock of the processor . The availab le options allow y ou to adjust the processor’ s bus clock by 1MHz increment.
94 3 BIOS Setup 3.1.9 Load Fail-Safe Defaults The “Load Fail-Saf e Defaults” option loads the troub leshooting default values per manentl y stored in the ROM chips. These settings are not optimal and tur n off all high performance features. Y ou should use these values only if you have hardware problems.
95 3 BIOS Setup 3.1.10 Load Optimized Defaults The “Load Optimized Defaults” option loads optimiz ed se ttings from the BIOS ROM. Use the default values as standard values for your system. Highlight this option in the main menu and press <Enter>.
96 3 BIOS Setup 3.1.11 Set Supervisor Password If you want to protect your system and setup from unauthorized entr y , set a super visor’ s passw ord with the “System” option selected in the Advanced BIOS Features.
97 3 BIOS Setup 3.1.12 Set User Password If you want another user to ha ve access only to your system but not to setup , set a user’ s password with the “System” option se- lected in the Advanced BIOS Features.
98 3 BIOS Setup 3.1.13 Sa v e & Exit Setup When all the changes hav e been made , highlight “Sav e & Exit Setup” and press <Enter>. T ype “Y” and press <Enter>. The modif ications y ou hav e made will be wr itten into the CMOS memor y , and the system will reboot.
99 3 BIOS Setup 3.1.14 Exit Without Sa ving When you do not want to save the changes you have made, highlight “Exit Without Saving” and press <Enter>. T ype “Y” and press <Enter>. The system will reboot and you will once again see the initial diagnostics on the screen.
100 3 BIOS Setup 3.2 Updating the BIOS T o update the BIOS, y ou will need the new BIOS f ile and a flash utility , A WDFLASH.EXE. Please contact technical suppor t or y our sales representative for the files. Note: A WDFLASH.EXE wor ks only in DOS mode.
101 3 BIOS Setup 6 . The following will appear . Do Y ou W ant to Sa ve BIOS (Y/N) This question refer s to the cur rent existing BIOS in y our system. W e recommend that you sa ve the current BIOS and its flash utility; just in case y ou need to reinstall the BIOS.
102 4 Supported Software 4.1 Desktop Management Interface (DMI) The system board comes with a DMI built into the BIOS. DMI, along with the appropr iately netw or ked software , is designed to make in ventor y , maintenance and troubleshooting of computer sys- tems easier .
103 4 Supported Software 4.1.2 Using the DMI Utility The four menus located on top of the DMI Configuration Utility screen are Edit DMI, Add DMI, Load DMI File and Sa ve DMI File . Use the ← or → (left or right) arrow keys to select a menu from the Menu bar .
104 4 Supported Software Add DMI 1. Use the ← or → ar ro w keys to select the Add DMI menu. 2. Highlight the item on the left screen that you would like to add by using the ↑ or ↓ arrow keys, then press <Enter>. 3. The cur sor will mov e to the screen y ou select allo wing y ou to enter information about the added item.
105 4 Supported Software 4.2 Driv ers, Utilities and Softwar e Applications The CD that came with the system board contains dr iver s, utilities and software applications required to enhance the performance of the system board. Inser t the CD into a CD-ROM drive .
106 4 Supported Software 4.2.1 Intel 875 INF Update Utility The Intel 875 INF Update Utility is used for updating Windows 98SE/2000/ME/XP's INF files so that the Intel chipset can be recognized and conf igured proper ly in the system. T o install the utility , please follo w the steps belo w .
107 4 Supported Software 4.2.2 Intel LAN Drivers T o install the dr iv er , please follo w the steps below . 1 . Click “Intel LAN Dr iver s” on the main menu. 2 . Click “Wired LAN Adapter s”. The following screen will appear . 3 . Click “Install Software”.
108 4 Supported Software 4.2.3 Intel USB 2.0 Drivers If you are using a USB 2.0 device, you must install the USB 2.0 dr iv er . The dr iver s are suppor ted in the f ollowing operating systems: Windo ws 98 SE, Windows ME and Windows 2000. T o install the driver , please follo w the steps below .
109 4 Supported Software Important: If you are using W indows ® ® ® ® ® XP , you must install the Windows Ser vice P ack 1 USB 2.0 dr iver which comes availab le after you have installed the operating system. 2 . Follow the installation instr uctions shown on the screen.
110 4 Supported Software 4.2.4 A u d i o D r i v e r s The audio dr iver s are suppor ted in the follo wing oper ating sys- tems: Windo ws 98SE, Windows ME, Windo ws NT 4.0, Windows 2000 and Windows XP . T o install the dr iv er , please follo w the steps below .
111 4 Supported Software 4.2.5 Microsoft DirectX 9 T o install, please follo w the steps belo w . 1 . Click “Microsoft DirectX 9” on the main menu . The follo wing screen will appear . 2 . Click “I accept the agreement” then click “Next”. 3 .
112 4 Supported Software 4.2.6 Hardware Doctor Hardware Doctor is capable of monitoring the system’ s hardware conditions such as the temperature of the CPU and system, volt- age, and speed of the cooling fans. It also allows you to manually set a range to the items being monitored.
113 4 Supported Software 4.3 Installation Notes 1. "Autor un" ONL Y suppor ts the Windows 98 SE, Windo ws ME, Windows 2000, Windows NT 4.
A 114 Enabling Hyper -Threading T echnolog y A . 1 Enabling Hyper -Thr eading T echnolog y T o enable the functionality of the Hyper -Threading T echnology , please follo w the requirements and steps below . Basicall y , the follo wing presumes that you ha ve already installed an Intel ® P entium ® 4 Processor with Hyper -Threading T echnology .
A Enabling Hyper -Threading T echnolog y 115 d. Now click the Hardware tab then click Device Manager . The items shown under Computer and Processor s should resemble the ones sho wn belo w . c. Click the Gener al tab . The processor sho wn under Computer should resemble the one shown belo w .
A 116 Enabling Hyper -Threading T echnolog y e. Lastly , press the <Ctr l> <Alt> and <Del> keys simultaneousl y . The Windo ws T ask Manager dialog box will appear . Click the P erfor mance tab . The diagr am under CPU Usage Histor y should resemb le the one sho wn below .
B CPU Fan Protection 117 The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circulation across the CPU and heat sink, the CPU will overheat damaging both the CPU and system board. The system board suppor ts the CPU Fan Protection function.
C 118 CPU T emperature Protection The CPU T emper ature Protection function has the capability of monitor ing the CPU’ s temper ature dur ing system boot-up . T o use the CPU T emper ature Protection function, please follo w the steps below . 1 . Select the “PC Health Status” submenu in the BIOS.
D System Error Message 119 When the BIOS encounter s an er ror that requires the user to correct something, either a beep code will sound or a message will be displayed in a box in the middle of the screen and the message, PRESS F1 T O CONTINUE, CTRL-AL T -ESC or DEL T O ENTER SETUP , will be shown in the information box at the bottom.
D 120 System Error Message setting than indicated in Setup. Determine which setting is correct, either turn off the system and change the jumper or enter Setup and change the VIDEO selection. FLOPPY DISK(S) fail (80) Unable to reset floppy subsystem. FLOPPY DISK(S) fail (40) Floppy type mismatch.
E T r oubleshooting 121 E.1 T r oubleshooting Checklist This chapter of the manual is designed to help you with problems that y ou may encounter with y our per sonal computer . T o efficientl y troubleshoot y our system, treat each prob lem individually .
E 122 T r oubleshooting The picture seems to be constantly moving. 1. The monitor has lost its ver tical sync . Adjust the monitor’s v er tical sync. 2. Move away any objects, such as another monitor or fan, that may be creating a magnetic f ield around the displa y .
E T r oubleshooting 123 Hard Drive Hard disk failure. 1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS. 2. If the system is configured with two hard drives, make sure the bootable (f i r st) hard dr ive is conf igured as Master and the second hard dr iv e is conf igured as Sla v e.
E 124 T r oubleshooting Serial Port The serial device (modem, printer) doesn’ t output anything or is outputting garbled characters. 1 . Make sure that the ser ial device’ s pow er is turned on and that the device is on-line. 2 . V er ify that the device is plugged into the cor rect ser ial por t on the rear of the computer .
Een belangrijk punt na aankoop van elk apparaat Intel System Board G4H875-B (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Intel System Board G4H875-B heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Intel System Board G4H875-B vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Intel System Board G4H875-B leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Intel System Board G4H875-B krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Intel System Board G4H875-B bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Intel System Board G4H875-B kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Intel System Board G4H875-B . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
