Gebruiksaanwijzing /service van het product Arrow RWD van de fabrikant Invacare
Ga naar pagina of 140
Part No. 1104849 1 3G Storm Series ® Wheelchairs Service Manual DEALER: KEEP THIS MANUAL. THE PROCEDURES IN THIS MANUAL MUST BE PERFORMED BY A QUALIFIED TECHNICIAN.
3G Storm Series ® Wheelchairs 2 Part No. 1104849 WARNING WARNING BEFORE INITIAL USE A QUALIFIED TECHNICIAN MUST PERFORM THE INITIAL SET UP OF THIS WHEELCHAIR.
Part No. 1104849 3 3G Storm Series ® Wheelchairs TABLE OF CONTENTS NOTE: The information in this owner's manual applies to the ARROW, TORQUE SP, RANGER X, and the RECLINER wheelchairs except where specified. SPECIAL NOTES .......................
3G Storm Series ® Wheelchairs 4 Part No. 1104849 SECTION 6 - SEAT FRAME SECTION 6 - SEAT FRAME SECTION 6 - SEAT FRAME SECTION 6 - SEAT FRAME SECTION 6 - SEAT FRAME ............................................................. ........................
Part No. 1104849 5 3G Storm Series ® Wheelchairs TABLE OF CONTENTS TABLE OF CONTENTS SECTION 12 - WHEELS/MOTORS ..................................................... 83 REPLACING PNEUMATIC TIRES/TUBES - DRIVE WHEELS/CASTERS ..........................
3G Storm Series ® Wheelchairs 6 Part No. 1104849 TYPICAL PRODUCT PARAMETERS - ARROW TYPICAL PRODUCT PARAMETERS - ARROW SEAT WIDTH RANGE: Standard: 12 t o 24 -i nches Recliner: 14 to 24-inches SEAT DE.
Part No. 1104849 7 3G Storm Series ® Wheelchairs TYPICAL PRODUCT PARAMETERS - ARROW TYPICAL PRODUCT PARAMETERS - ARROW TYPICAL PRODUCT PARAMETERS - ARROW PHYSICAL DIMENSIONS CASTERS W/PRECISION SEALE.
3G Storm Series ® Wheelchairs 8 Part No. 1104849 TYPICAL PRODUCT PARAMETERS - TORQUE SP TYPICAL PRODUCT PARAMETERS - TORQUE SP SEAT WIDTH RANGE: Standard: 12 t o 22 -i nches Recliner: 14 to 22-inches.
Part No. 1104849 9 3G Storm Series ® Wheelchairs TYPICAL PRODUCT PARAMETERS - TORQUE SP TYPICAL PRODUCT PARAMETERS - TORQUE SP TYPICAL PRODUCT PARAMETERS - TORQUE SP PHYSICAL DIMENSIONS CASTERS W/PRE.
3G Storm Series ® Wheelchairs 10 Part No. 1104849 TYPICAL PRODUCT PARAMETERS - RANGER X TYPICAL PRODUCT PARAMETERS - RANGER X SEAT WIDTH RANGE: Standard: 12 t o 22 -i nches Recliner: 14 to 22-inches .
Part No. 1104849 11 3G Storm Series ® Wheelchairs TYPICAL PRODUCT PARAMETERS - RANGER X TYPICAL PRODUCT PARAMETERS - RANGER X TYPICAL PRODUCT PARAMETERS - RANGER X PHYSICAL DIMENSIONS CASTERS W/PRECI.
3G Storm Series ® Wheelchairs 12 Part No. 1104849 GENERAL GUIDELINES SECTION 1 This Section Includes the Following: Repair or Service Information Operating Information Label Location Warning/Caution .
Part No. 1104849 13 3G Storm Series ® Wheelchairs GENERAL GUIDELINES SECTION 1 GENERAL GUIDELINES BATTERIES The warranty and performance specifications contained in this manual are based on the use of deep cycle gel cell batteries. Invacare strongly recommends their use as the power source for this unit.
3G Storm Series ® Wheelchairs 14 Part No. 1104849 GENERAL GUIDELINES SECTION 1 GENERAL GUIDELINES CAUTION For safe product function, material compatibility, proper installation, operation and maintenance, you must only use parts, accessories and adapters manufactured or supplied by Invacare.
Part No. 1104849 15 3G Storm Series ® Wheelchairs NOTE: These caution labels are only found on battery boxes used with the gearless/brushless motor. GROUP 24 BATTERIES 22NF BATTERIES LABEL LOCATION TIRE PRESSURE WARNING The recommended tire pressure is listed on the side wall of each tire.
3G Storm Series ® Wheelchairs 16 Part No. 1104849 1070497 MUST SHIPPING TIE DOWN RESTRAINTS Base Frame Frame End Caps WARNING/CAUTION LABEL LOCATION REAR OF WHEELCHAIR FRONT OF WHEELCHAIR NOTE: WARNING LABEL also found on side frame near the rear of the chair.
Part No. 1104849 17 3G Storm Series ® Wheelchairs SECTION 2 TROUBLESHOOTING This Section Includes the Following: Field Load Test Motor Testing Motor Brush Inspection Electro-Mechanical Parking Brake .
3G Storm Series ® Wheelchairs 18 Part No. 1104849 SECTION 2 TROUBLESHOOTING TROUBLESHOOTING 4 Pin Motor Connector Motor FIGURE 3 - MOTOR BRUSH INSPECTION Cap MOTOR TESTING (FIGURE 2) NOTE: This procedure should only be performed on wheelchairs with the conventional motor/gearbox assembly.
Part No. 1104849 19 3G Storm Series ® Wheelchairs Once the motor brush caps have been removed, pull the brushes out of the motor. The end of the brushes should be smooth and shiny and the spring should not be damaged or discolored. If one or both of the brushes are damaged, only the damaged or worn brushes need be replaced.
3G Storm Series ® Wheelchairs 20 Part No. 1104849 SECTION 3 HARDWARE TORQUE SPECIFICATIONS HARDWARE TORQUE SPECIFICATIONS Torque to 156 in-lbs **Torque to 156 in-lbs **Torque to 156 in-lbs HARDWARE TORQUE SPECIFICATIONS STANDARD SEAT FRAME NOTE: * These torque specifications also apply to the ASBA assembly.
Part No. 1104849 21 3G Storm Series ® Wheelchairs HARDWARE TORQUE SPECIFICATIONS *VAN SEAT Loctite and Torque to 75 in-lbs Torque to 156 in-lbs Torque to 156 in-lbs * NOTE: For additional torque specifications, refer to the torque specifications drawing for the standard seat frame assembly.
3G Storm Series ® Wheelchairs 22 Part No. 1104849 HARDWARE TORQUE SPECIFICATIONS Torque to 75 in-lbs *ASBA (ADJUSTABLE SEAT BACK ANGLE) Torque to 156 in-lbs Torque to 156 in-lbs Torque to 156 in-lbs Torque to 156 in-lbs * NOTE: For additional torque specifications, refer to the torque specifications drawing for the standard seat frame assembly.
Part No. 1104849 23 3G Storm Series ® Wheelchairs HARDWARE TORQUE SPECIFICATIONS HARDWARE TORQUE SPECIFICATIONS Torque to 156 in-lbs Loctite and torque to 156 in-lbs Torque to 85 ft-lbs 8-inch Wheels.
3G Storm Series ® Wheelchairs 24 Part No. 1104849 Adjustment Screw BASE FRAME - STANDARD GEARLESS/BRUSHLESS MOTOR (FOR WHEELCHAIRS BU ILT BEFORE 1/26/04) Torque to 13 ft-lbs Torque to 13 ft-lbs Torqu.
Part No. 1104849 25 3G Storm Series ® Wheelchairs SECTION 4 ARMS This Section Includes the Following: Replacing Van Seat Armrest Pads FIGURE 1 - REPLACING VAN SEAT ARMREST PADS WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.
3G Storm Series ® Wheelchairs 26 Part No. 1104849 UPHOLSTERY/POSITIONING STRAP SECTION 5 UPHOLESTERY/ POSITIONING STRAP This Section Includes the Following: Replacing Van Seat Positioning Strap Repla.
Part No. 1104849 27 3G Storm Series ® Wheelchairs REPLACING BACK UPHOLSTERY (FIGURE 2) 1 . Remove one (1) armrest from the wheelchair. Refer to INSTALLING/REMOVING FLIP BACK ARMRESTS in SECTION 4 of the Owner’s Manual, part number 1104782 or 1123757.
3G Storm Series ® Wheelchairs 28 Part No. 1104849 HEAVY DUTY MODELS BACK HEIGHT ◆ ◆ ◆ ◆ ◆ SPREADER BAR HEIGHT 16-17-inches 5-inches 18-24-inches 7-inches NOTE: Spreader bar required on all back heights. ◆ ◆ ◆ ◆ ◆ Height of Spreader Bar from Bottom of Back Canes to Top of Spreader Bar Clamp.
Part No. 1104849 29 3G Storm Series ® Wheelchairs SEAT FRAME This Section Includes the Following: Preparation for Removing/Installing Seat Frame (Standard Frame, ASBA, and Van Seat) Replacing Same Si.
3G Storm Series ® Wheelchairs 30 Part No. 1104849 SEAT FRAME SECTION 6 3 . Cut tie wraps and disconnect joystick from controller. 4 . Turn the lever on the adjustment lock to release the adjustment lock from the joystick mounting tube. 5 . Remove the joystick from the wheelchair.
Part No. 1104849 31 3G Storm Series ® Wheelchairs REPLACING SAME SIZE STANDARD SEAT FRAME 1 . Perform the instructions outlined in PREPARATION FOR REMOVING/INSTALLING SEAT FRAME (STANDARD FRAME, ASBA, AND VAN SEAT) in this section of the manual. 2 . Remove the existing standard seat frame subassembly and install the NEW standard frame.
3G Storm Series ® Wheelchairs 32 Part No. 1104849 SEAT FRAME CHANGING SEAT DEPTH STANDARD SEAT FRAME NOTE: Review the chart below. This will determine the components needed to obtain the desired seat depth.
Part No. 1104849 33 3G Storm Series ® Wheelchairs ASBA (FIGURE 3) NOTE: Review the chart below. This will determine the components needed to obtain your desired seat depth. 1 . Find current seat depth in left hand column in the chart. 2 . Follow that row to right under seat frame components.
3G Storm Series ® Wheelchairs 34 Part No. 1104849 SEAT FRAME SECTION 6 SEAT FRAME E . Remove the four (4) mounting screws that secure the EXISTING center frame to support brackets. F . Remove existing center frame from seat mount plates. G . Secure NEW center frame to support brackets with the existing four (4) mounting screws and locknuts.
Part No. 1104849 35 3G Storm Series ® Wheelchairs CHANGING SEAT DEPTH BETWEEN 12 AND 15-INCHES (FIGURE 4) NOTE: There are two (2) sizes of CJ back brackets. Refer to the following chart to determine if the seat depth required is obtainable by repositioning the back canes only, or if the CJ back brackets must be replaced.
3G Storm Series ® Wheelchairs 36 Part No. 1104849 SEAT FRAME SECTION 6 SEAT FRAME ALLOWABLE SEAT WIDTH AND DEPTH COMBINATIONS FOR ASBA 12 13 14 15 16 12 ✓✓ ✓ ✓ ✓ 13 ✓✓ ✓ ✓ ✓ 14 .
Part No. 1104849 37 3G Storm Series ® Wheelchairs WARNING Both side frames MUST be adjusted to the same mounting hole position to maintain proper weight balance of user and seat frame. If weight is not balanced, injury to the assistant and/or user and damage to the wheelchair may result.
3G Storm Series ® Wheelchairs 38 Part No. 1104849 SEAT FRAME SECTION 6 SEAT FRAME INSTALLING/REMOVING ASBA SUBASSEMBLY AND/OR COMPONENT REPLACEMENT (FIGURE 6) CONVERTING FROM ASBA TO STANDARD SEAT FRAME OR VAN SEAT NOTE: This section must be performed in conjunction with a starting procedure.
Part No. 1104849 39 3G Storm Series ® Wheelchairs 4 . Remove the four (4) mounting screws and locknuts that secure the center frame to the support brackets. 5 . Secure NEW center frame to support brackets with existing four (4) mounting screws and locknuts.
3G Storm Series ® Wheelchairs 40 Part No. 1104849 SEAT FRAME SECTION 6 SEAT FRAME INSTALLING/REMOVING VAN SEAT ASSEMBLY (FIGURE 7) INSTALLING VAN SEAT 1 . Position the van seat on the seat mounting plates at the position shown in FIGURE 7. 2 . Line up mounting holes in the van seat frame and the mounting holes in the seat mounting plates.
Part No. 1104849 41 3G Storm Series ® Wheelchairs CONVERTING FROM STANDARD SEAT FRAME TO ASBA OR VICE VERSA 1 . Perform the instructions outlined in PREPARATION FOR REMOVING/INSTALLING SEAT FRAME (STANDARD FRAME, ADJUSTABLE FRAME, AND VAN SEAT) in this section of the manual.
3G Storm Series ® Wheelchairs 42 Part No. 1104849 SECTION 6 SEAT FRAME SEAT FRAME CONVERTING FROM ASBA TO VAN SEAT OR VICE VERSA 1 . Perform the instructions outlined in PREPARATION FOR REMOVING/INSTALLING SEAT FRAME (STANDARD FRAME, ADJUSTABLE FRAME, AND VAN SEAT) in this section of the manual.
Part No. 1104849 43 3G Storm Series ® Wheelchairs CONVERTING FROM STANDARD SEAT FRAME TO VAN SEAT OR VICE VERSA 1 . Perform the instructions outlined in PREPARATION FOR REMOVING/INSTALLING SEAT FRAME (STANDARD FRAME, ADJUSTABLE FRAME, AND VAN SEAT) in this section of the manual.
3G Storm Series ® Wheelchairs 44 Part No. 1104849 SECTION 6 SEAT FRAME SEAT FRAME INSTALLING 1. Position the NEW seat pan on the seat frame, aligning the mounting holes of the seat pan and the mounting holes of the seat frame.
Part No. 1104849 45 3G Storm Series ® Wheelchairs Mounting Screw Medium Height Seat Mount Plate Front of Seat Frame Mounting Screw Rear of Seat Frame DETAIL “A” FIGURE 10 - SEAT ANGLE ADJUSTMENT SEAT ANGLE ADJUSTMENT (FIGURE 10) NOTE: The angle of the seat is factory set providing the user with a 5 o seat dump.
3G Storm Series ® Wheelchairs 46 Part No. 1104849 SECTION 7 BASE FRAME BASE FRAME This Section Includes the Following: Replacing Seat Mounting Plates Replacing Seat Support Brackets Replacing Seat Su.
Part No. 1104849 47 3G Storm Series ® Wheelchairs REPLACING SEAT SUPPORT BRACKETS (FIGURE 2) 1 . Perform the instructions outlined in P REPARATION FOR REMOVING/INSTALLING SEAT FRAME (STANDARD FRAME, ADJUSTABLE FRAME, AND VAN SEAT) in SECTION 6 of this manual.
3G Storm Series ® Wheelchairs 48 Part No. 1104849 BASE FRAME SECTION 7 BASE FRAME 7. Adjust seat mount plates to desired angle. Refer to SEAT ANGLE ADJUSTMENT in SECTION 6 of this manual.
Part No. 1104849 49 3G Storm Series ® Wheelchairs NOTE: Before removing seat mounting plates, note the position of the washers. 4 . Remove the seat support brackets. Refer to REPLACING SEAT SUPPORT BRACKETS in this section of the manual. 5 . Remove the seat stop screw that is closest to the end cap.
3G Storm Series ® Wheelchairs 50 Part No. 1104849 4 . Remove the two (2) mounting screws that secure the battery charger connector to the mount bracket. 5 . Remove battery charger connector from mount bracket. 6. Remove the mounting screw which secures the battery charger mount bracket to the T-nut located in the channel of the base frame.
Part No. 1104849 51 3G Storm Series ® Wheelchairs This Section Includes the Following: Removing/Installing CJ Back Brackets Changing Back Height Back Angle Adjustment REMOVING/INSTALLING CJ BACK BRACKETS (FIGURE 1) NOTE: The following procedure is for Jr.
3G Storm Series ® Wheelchairs 52 Part No. 1104849 BACK FRAME SECTION 8 WARNING Always wear your seat positioning strap. 3 . Position the seat positioning strap and quick release pin under the CJ back bracket. 4 . Secure the quick release pin, seat positioning strap, and CJ back bracket to the seat frame.
Part No. 1104849 53 3G Storm Series ® Wheelchairs CHANGING BACK HEIGHT (FIGURE 2) NOTE: If changing the back height, new back upholstery may be needed as well.
3G Storm Series ® Wheelchairs 54 Part No. 1104849 BACK FRAME 14 . Secure the top of the existing/new back upholstery to the back canes with the two (2) existing mounting screws and washers. 15 . Secure bottom of the existing/NEW back upholstery to rear of the seat pan.
Part No. 1104849 55 3G Storm Series ® Wheelchairs BACK ANGLE ADJUSTMENT (FIGURE 3) 1 . Remove armrests from the wheelchair. Refer to INSTALLING/REMOVING FLIP BACK ARMRESTS in SECTION 4 of the Owner’s Manual, part number 1104782 or 1123757. 2 . Remove the mounting screw and washer from the top mounting hole of back angle plate and back cane.
3G Storm Series ® Wheelchairs 56 Part No. 1104849 BATTERIES SECTION 9 BATTERIES This Section Includes the Following: Warnings for Handling and Replacing Batteries Using the Proper Batteries Installin.
Part No. 1104849 57 3G Storm Series ® Wheelchairs USING THE PROPER BATTERIES (FIGURES 1 AND 2) 1 . Place battery on ground/flat surface. 2 . Visually draw a horizontal and vertical centerline through the middle of battery. 3 . Position the battery so that the terminals are above the horizontal centerline.
3G Storm Series ® Wheelchairs 58 Part No. 1104849 POSITIVE (+) Battery Terminal/Post NEGATIVE (-) Battery Terminal/Post NEGATIVE (-) Battery Terminal/Post WARNING FOR 3G STORM WHEELCHAIRS THAT USE GP24 BATTERIES: Batteries with terminal configuration (positive on the right and negative on the left) as shown below MUST be used.
Part No. 1104849 59 3G Storm Series ® Wheelchairs NOTE: If there is battery acid in the bottom or on the sides of the battery box(es) or battery(ies), apply baking soda to these areas to neutralize the battery acid. Before reinstalling the NEW or existing battery(ies), clean the baking soda from the battery box(es) or battery(ies).
3G Storm Series ® Wheelchairs 60 Part No. 1104849 DISCONNECTING/CONNECTING BATTERY CABLES WARNING NEVER allow any of your tools and/or battery cable(s) to contact BOTH battery post(s) at the same time. An electrical short may occur and serious personal injury or damage may occur.
Part No. 1104849 61 3G Storm Series ® Wheelchairs P 5 . Verify battery cable clamps(s) are correctly installed and securely tightened. 6 . Reposition battery clamp covers over battery post(s). 7 . Install the battery box top(s). 8 . Install the battery box(es) into the wheelchair.
3G Storm Series ® Wheelchairs 62 Part No. 1104849 GROUP 24 BATTERIES ON WHEELCHAIRS BUILT AFTER 1/25/04 (FIGURE 5) Disconnecting. NOTE: Perform this section on one (1) battery and battery box at a time. Repeat section for other battery box. 1 . Lift up on battery box lid to expose underlying cables.
Part No. 1104849 63 3G Storm Series ® Wheelchairs FIGURE 5 - DISCONNECTING/CONNECTING BATTERY CABLE(S) - GROUP 24 BATTERIES Top View of Battery POSITIVE (+) Battery Terminal/Post NEGATIVE (-) Battery.
3G Storm Series ® Wheelchairs 64 Part No. 1104849 22N F BATTERIES IN SINGLE BATTERY BOX (FIGURE 5) NOTE: Note polarity of white battery cable (jumper) battery terminal ends. Disconnecting. 1 . Remove battery terminal cap(s) from battery terminal(s) ends.
Part No. 1104849 65 3G Storm Series ® Wheelchairs FIGURE 5 - CONNECTING BATTERY CABLES - SINGLE 22NF BATTERY BOX Terminal Cap STEPS 5 AND 6 Battery Box Top Front Battery POSITIVE (+) RED Battery Cable Battery Box Bottom Rear Battery POSITIVE (+) Battery Terminal/Post NOTE: Battery box top cut away for clarification purposes only.
3G Storm Series ® Wheelchairs 66 Part No. 1104849 WHEN TO CHARGE BATTERIES (FIGURE 6) MKIV-A AND MKIV-RII JOYSTICKS The Battery Discharge Indicator (BDI) is a bar graph display located on the MKIV joystick. It will keep you informed as to power availability.
Part No. 1104849 67 3G Storm Series ® Wheelchairs NOTE: As a general rule, batteries should be recharged daily to assure the longest possible life and minimize the required charging time. Plan to recharge the batteries when it is anticipated the wheelchair will not be used for a long period of time.
3G Storm Series ® Wheelchairs 68 Part No. 1104849 WHEELCHAIRS EQUIPPED WITH MCC-MARK IV JOYSTICK WHEELCHAIRS EQUIPPED WITH MARK IV RII JOYSTICK From Battery Charger Battery Charger Connector From Bat.
Part No. 1104849 69 3G Storm Series ® Wheelchairs REPLACING BATTERIES NOTE: Invacare recommends that both batteries be replaced if one (1) battery is defective. RECOMMENDED BATTERY TYPES WARNING Failure to use the correct battery size and/or voltage may cause damage to your wheelchair and give you unsatisfactory performance.
3G Storm Series ® Wheelchairs 70 Part No. 1104849 NOTE: Weight limitation is total weight: user weight plus any additional items that the user may require (back pack, etc.
Part No. 1104849 71 3G Storm Series ® Wheelchairs CLEANING BATTERY TERMINALS WARNING Most batteries are not sold with instructions. However, warnings are frequently noted on the cell caps. Read them carefully. DO NOT allow the liquid in the battery to come in contact with skin, clothes or other possessions.
3G Storm Series ® Wheelchairs 72 Part No. 1104849 Installing. 1 . Place the wheelchair in a well ventilated area where work can be performed without risking damage to carpeting or floor covering. 2 . Verify the joystick ON/OFF switch is in the OFF position.
Part No. 1104849 73 3G Storm Series ® Wheelchairs GROUP 24 BATTERY BOXES FOR WHEELCHAIRS EQUIPPED WITH VENT TRAY (FIGURE 9) WARNING Each battery weighs 51 pounds.
3G Storm Series ® Wheelchairs 74 Part No. 1104849 7 . Place one (1) connector battery box onto battery sub-frame. 8 . Slide one (1) connector battery box along the sub-frame until its guide pins are engaged in the connector of the two (2) connector battery box.
Part No. 1104849 75 3G Storm Series ® Wheelchairs This Section Includes the Following: Removing/Installing the Wiring Harness Adjusting Limit Switch WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.
3G Storm Series ® Wheelchairs 76 Part No. 1104849 Tie-Wraps A and B Wiring Harness Connector (BLUE) Controller Connector (BLUE) Motor Connector Controller Connector Mounting Screws (not shown) Batter.
Part No. 1104849 77 3G Storm Series ® Wheelchairs 22NF BATTERIES (FIGURE 2) Removing. 1. Remove the battery boxes. Refer to REMOVING/INSTALLING BATTERY BOXES in SECTION 9 of this manual. 2. Cut the tie wrap that secures the rear portion of the wiring harness and joystick cable to the rear of the seat frame (DETAIL “A”).
3G Storm Series ® Wheelchairs 78 Part No. 1104849 DETAIL “C” - WHEELCHAIRS WITH GEARLESS/BRUSHLESS MOTOR SECTION 10 WIRING HARNESS FIGURE 2 - REMOVING/INSTALLING THE WIRING HARNESS - 22NF BATTERIES WIRING HARNESS DETAIL “A” - 22NF BATTERIES NOTE: Illustration depicts gearless/brushless motor.
Part No. 1104849 79 3G Storm Series ® Wheelchairs ADJUSTING LIMIT SWITCH (FIGURE 3) NOTE: The following section is for high back van seat model wheelchairs only. WARNING NEVER operate the wheelchair while in any recline position over 114 ° RELATIVE TO THE SEAT FRAME.
3G Storm Series ® Wheelchairs 80 Part No. 1104849 B. Loosen, but do not remove, the two (2) phillips screws, washers and locknuts that secure the actuator to the upper limit switch bracket. C. Slide the actuator UP (towards the top of the wheelchair).
Part No. 1104849 81 3G Storm Series ® Wheelchairs RETENTION STRAP/RETAINER SECTION 11 This Section Includes the Following: Replacing Battery Box Retainer Bar/Retainer Clip WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.
3G Storm Series ® Wheelchairs 82 Part No. 1104849 Retainer Clip Mounting Screws Battery Box Sub-frame Base Frame Retainer Bar Shock Assembly Spacer SECTION 11 FIGURE 1 - REPLACING BATTERY BOX RETAINE.
Part No. 1104849 83 3G Storm Series ® Wheelchairs WHEELS/MOTORS This Section Includes the Following: Replacing Pneumatic Tires/Tubes - Drive Wheels/Casters Removing/Installing Drive Wheels Removing/I.
3G Storm Series ® Wheelchairs 84 Part No. 1104849 REMOVING 1. Remove the battery boxes. Refer to REMOVING/INSTALLING BATTERY BOXES in SECTION 9 of this manual. 2. Remove the four (4) beveled hex nuts that secures the drive wheel assembly to one of the following: drive wheel hub, GB motor spacer or adapter plate with studs.
Part No. 1104849 85 3G Storm Series ® Wheelchairs Locknut Washer Keystock Drive Wheel Hub FIGURE 2 - REMOVING/INSTALLING DRIVE WHEEL HUB Motor Gearbox REMOVING/INSTALLING DRIVE WHEEL HUB (FIGURE 2) REMOVING 1. Remove the drive wheel from the wheelchair.
3G Storm Series ® Wheelchairs 86 Part No. 1104849 REMOVING/INSTALLING GB MOTOR SPACER (FIGURE 3) REMOVING 1. Remove the drive wheel from the wheelchair. Refer to REMOVING/INSTALLING DRIVE WHEELS in this section of the manual. 2. Remove the four (4) locknuts that secure the GB motor spacer to the GB motor.
Part No. 1104849 87 3G Storm Series ® Wheelchairs SECTION 12 WHEELS/MOTORS INSTALLING WHEEL LOCK BRACKET ONTO WHEELCHAIR (FIGURE 5) NOTE: This SECTION only pertains to wheelchairs with the conventional motor and gearbox. On wheelchairs with the gearless/brushless motor, the wheel lock bracket is not required.
3G Storm Series ® Wheelchairs 88 Part No. 1104849 WHEELS/MOTORS REMOVING/INSTALLING THE RIM AND/OR TIRE (FIGURE 6) NOTE: This procedure is for wheelchairs equipped with heavy duty gearless/brushless motors before 1/26/04 and standard gearless/brushless motors after 1/25/04.
Part No. 1104849 89 3G Storm Series ® Wheelchairs WHEELS/MOTORS B. Secure new/existing rim and new/existing tire with flat free to gearless/brushless motor with the three (3) M8 x 1-1/4 x 25 mm mounting screws (not provided). See DETAIL “A” in FIGURE 6.
3G Storm Series ® Wheelchairs 90 Part No. 1104849 REPLACING FORKS (FIGURE 8) 1. Remove the caster from the existing fork. Refer to REMOVING/INSTALLING CASTERS in this section of the manual. 2. Remove the dust cover . 3. Remove the locknut, nylon washer, and spacer.
Part No. 1104849 91 3G Storm Series ® Wheelchairs REMOVING/INSTALLING THE MOTOR CONVENTIONAL MOTOR WITH GEARBOX (FIGURE 9) Removing. 1. Disconnect the right and/or left motor connector from the controller. 2. Remove the two (2) allen screws and washers that secure the motor to the gearbox.
3G Storm Series ® Wheelchairs 92 Part No. 1104849 STANDARD GEARLESS/BRUSHLESS MOTOR BEFORE 1/26/04 (FIGURE 10) Removing. 1. Remove the battery boxes. Refer to REMOVING / INSTALLING BATTERY BOXES in SECTION 9 of this manual. 2. Unthread the mounting screws that secure the wiring harness connector to the motor.
Part No. 1104849 93 3G Storm Series ® Wheelchairs 8. If necessary, install the 22NF battery box tray. Refer to REMOVING/INSTALLING 22NF BATTERY BOX TRAY in SECTION 15 of this manual. 9. Plug the wiring harness connector into the motor. 10. Secure the wiring harness connector to the motor with the existing two (2) mounting screws.
3G Storm Series ® Wheelchairs 94 Part No. 1104849 HEAVY DUTY GEARLESS/BRUSHLESS MOTOR (FIGURE 11) Removing. 1. Remove the battery boxes. Refer to REMOVING / INSTALLING BATTERY BOXES in SECTION 9 of this manual. 2. Unthread the mounting screws that secure the wiring harness connector (not shown) to the motor.
Part No. 1104849 95 3G Storm Series ® Wheelchairs SECTION 12 WHEELS/MOTORS WHEELS/MOTORS FIGURE 11 - REMOVING/INSTALLING THE MOTOR - HEAVY-DUTY GEARLESS/BRUSHLESS MOTOR Upper Mounting Screws Washers .
3G Storm Series ® Wheelchairs 96 Part No. 1104849 INSTALLING/REMOVING FENDERS 4 POLE MOTORS (FIGURE 12) Installing. 1. Remove the drive wheel. Refer to REMOVING/INSTALLING THE DRIVE WHEELS in this section of the manual.
Part No. 1104849 97 3G Storm Series ® Wheelchairs SECTION 12 WHEELS/MOTORS WHEELS/MOTORS Removing. 1. Remove the drive wheel. Refer to REMOVING/INSTALLING THE DRIVE WHEELS in this section of the manual.
3G Storm Series ® Wheelchairs 98 Part No. 1104849 FIGURE 13 - INSTALLING/REMOVING FENDERS - STANDARD GEARLESS/ BRUSHLESS MOTORS BEFORE 1/26/04 SECTION 12 WHEELS/MOTORS WHEELS/MOTORS STANDARD GEARLESS/BRUSHLESS MOTORS BEFORE 1/26/04 (FIGURE 13) Installing.
Part No. 1104849 99 3G Storm Series ® Wheelchairs Two (2) Top Mounting Screws FIGURE 14 - INSTALLING/REMOVING FENDERS - HEAVY DUTY GEARLESS/BRUSHLESS MOTORS Suspension Arm Gearless/Brushless Fender Bracket Fender Spacer Pan Head Tap Screws Fender HEAVY DUTY GEARLESS/BRUSHLESS MOTORS (FIGURE 14) Installing.
3G Storm Series ® Wheelchairs 100 Part No. 1104849 SECTION 13 ELECTRONICS This Section Includes the Following: Repositioning MKIV Joystick - Van Seat Models Removing/Installing the MKIV Controller WA.
Part No. 1104849 101 3G Storm Series ® Wheelchairs ELECTRONICS SECTION 13 ELECTRONICS REMOVING/INSTALLING THE MKIV CONTROLLER REMOVING MKIV CONTROLLER (WHEELCHAIRS EQUIPPED WITH NON-POWERED SEATING SYSTEMS) (FIGURE 2) 1. Remove the battery boxes. Refer to REMOVING/INSTALLING THE BATTERY BOXES in SECTION 9 of this manual.
3G Storm Series ® Wheelchairs 102 Part No. 1104849 SECTION 13 ELECTRONICS FIGURE 2 - REMOVING/INSTALLING THE MKIV CONTROLLER (WHEELCHAIRS EQUIPPED WITH NON-POWERED SEATING SYSTEMS) 8-32 x 1/2-inch Mo.
Part No. 1104849 103 3G Storm Series ® Wheelchairs ELECTRONICS REMOVING GB CONTROLLER (WHEELCHAIRS EQUIPPED WITH NON-POWERED SEATING SYSTEMS) (FIGURE 3) 1. Remove the battery boxes. Refer to REMOVING/INSTALLING THE BATTERY BOXES in SECTION 9 of this manual.
3G Storm Series ® Wheelchairs 104 Part No. 1104849 FIGURE 3 - REMOVING/INSTALLING THE GB CONTROLLER (WHEELCHAIRS EQUIPPED WITH NON-POWERED SEATING SYSTEMS) 10-32 x 1/2-inch Mounting Screw 8-32 x 1/2-.
Part No. 1104849 105 3G Storm Series ® Wheelchairs ELECTRONICS REMOVING MKIV CONTROLLER (WHEELCHAIRS EQUIPPED WITH 2ND GENERATION POWERED SEATING SYSTEMS) (FIGURE 4) 1. Remove the battery boxes. Refer to REMOVING/INSTALLING THE BATTERY BOXES in SECTION 9 of this manual.
3G Storm Series ® Wheelchairs 106 Part No. 1104849 SECTION 13 ELECTRONICS 8-32 x 1/2-inch Mounting Screws Controller Bracket 8-32 x 1/2-inch Mounting Screw 5/16-18 x 1-inch Hex Head Cap Screw Jumper .
Part No. 1104849 107 3G Storm Series ® Wheelchairs ELECTRONICS SECTION 13 ELECTRONICS REMOVING GB CONTROLLER (WHEELCHAIRS EQUIPPED WITH 2ND GENERATION POWERED SEATING SYSTEMS) (FIGURE 5) 1. Remove the battery boxes. Refer to REMOVING/INSTALLING THE BATTERY BOXES in SECTION 9 of this manual.
3G Storm Series ® Wheelchairs 108 Part No. 1104849 SECTION 13 ELECTRONICS 10-32 x 1/2-inch Mounting Screws (STEP 1) Jumper Cable 5/16-18 x 1-inch Hex Head Cap Screw Controller Bracket 10-32 x 1/2-inc.
Part No. 1104849 109 3G Storm Series ® Wheelchairs RECLINER This Section Includes the Following: Positioning Limit Switch Adjusting Limit Switch Replacing Recliner Cable Assemblies Replacing/Adjustin.
3G Storm Series ® Wheelchairs 110 Part No. 1104849 9. Secure limit switch sensor to the seat frame with the two (2) mounting screws and washers. 10. Secure the wire retainer onto the INSIDE of the seat frame with the mounting screw. 11. Tie wrap the limit switch wire to the seat frame.
Part No. 1104849 111 3G Storm Series ® Wheelchairs RECLINER SECTION 14 RECLINER REPLACING RECLINER CABLE ASSEMBLIES (FIGURE 3) NOTE: There are three (3) different cable lengths depending on back heig.
3G Storm Series ® Wheelchairs 112 Part No. 1104849 SECTION 14 RECLINER CAUTION DO NOT force the gas cylinder rod into the operator of the recliner cable assembly.
Part No. 1104849 113 3G Storm Series ® Wheelchairs RECLINER R E C L I N E R REPLACING/ADJUSTING GAS CYLINDERS (FIGURE 4) WARNING Replace ONE (1) gas cylinder at a time to avoid injury. Both gas cylinders MUST be operational and adjusted properly BEFORE using the recliner.
3G Storm Series ® Wheelchairs 114 Part No. 1104849 9. Line up the mounting holes of the NEW gas cylinder and the bracket of the back cane. 10. Reinstall the mounting screw through the mounting bracket of the back cane, nylon washer, NEW gas cylinder, nylon washer, mounting bracket and washer and securely tighten with the existing locknut.
Part No. 1104849 115 3G Storm Series ® Wheelchairs RECLINER 6. Turn the spreader bar on the existing back canes CLOCKWISE (toward back upholstery) and remove the spreader bar from the existing back canes. 7. Loosely install the spreader bar onto the NEW back cane handles by rotating the spreader bar COUNTERCLOCKWISE (away from the back canes).
3G Storm Series ® Wheelchairs 116 Part No. 1104849 SECTION 14 RECLINER CHANGING SEAT DEPTH (FIGURE 6) NOTE: 16-inch, 17-inch, 18-inch or 19-inch seat depths CAN NOT be increased to 20-inches or deeper.
Part No. 1104849 117 3G Storm Series ® Wheelchairs CHANGING SEAT WIDTH To change seat width, the seat frame must be changed to the desired width. Refer to INSTALLING/REPLACING ADJUSTABLE 16 TO 19-INCH DEEP RECLINER SEAT FRAME ONTO ARROW OR X BASE FRAME in this section of the manual.
3G Storm Series ® Wheelchairs 118 Part No. 1104849 RECLINER SECTION 14 RECLINER R E C L I N E R FIGURE 7 - INSTALLING/ REPLACING ADJUSTABLE 16 TO 19-INCH DEEP RECLINER SEAT FRAME ONTO ARROW OR X BASE Mounting Screws Base Frame Spacer Recliner Seat Assembly Seat Mount Plate Locknuts Warning Label Inside of Suspension Arm Assembly 6.
Part No. 1104849 119 3G Storm Series ® Wheelchairs SECTION 15 RWD WHEELCHAIRS RWD WHEELCHAIRS This Section Includes the Following: Removing/Installing Group 24 Battery Box Sub-Frame Removing/Installi.
3G Storm Series ® Wheelchairs 120 Part No. 1104849 Mounting Screws Battery Box Sub-frame Base Frame Shock FRONT OF CHAIR REAR OF CHAIR Retainer Bar Retainer Clip Spacer 2.
Part No. 1104849 121 3G Storm Series ® Wheelchairs REMOVING/INSTALLING 22NF BATTERY BOX TRAY (FIGURE 2) REMOVING 1. Remove the battery box. Refer to REMOVING/INSTALLING BA TTERY BOXES in SECTION 9 of this manual. 2. Remove the two (2) rear locknuts that secure the battery box tray to battery mount brackets.
3G Storm Series ® Wheelchairs 122 Part No. 1104849 Spacer Battery Mount Bracket *Rubber Element (or Shock Assembly) Mounting Screws Base Frame FIGURE 3 - REMOVING 22NF COMPONENTS *NOTE: Illustration depicts rubber element. Battery Mount Brackets remove in the same manner for the shock assembly.
Part No. 1104849 123 3G Storm Series ® Wheelchairs B. WHEELCHAIRS EQUIPPED WITHOUT VENT TRAY - Reinstall the four (4) mounting screws that secure the shocks and spacers to the base frame. 5. Perform STEPS 2-7 of REMOVING/INSTALLING THE WIRING HARNESS in SECTION 10 of this manual to complete the wiring harness installation.
3G Storm Series ® Wheelchairs 124 Part No. 1104849 RWD WHEELCHAIRS SECTION 15 RWD WHEELCHAIRS SHOCK OR RUBBER ELEMENT REPLACEMENT GROUP 24 BATTERIES (FIGURES 5 AND 6) 1. Remove the group 24 battery boxes. Refer to REMOVING/INSTALLING BATTERY BOXES in SECTION 9 of this manual.
Part No. 1104849 125 3G Storm Series ® Wheelchairs B. Wheelchairs without vent tray - Secure the top of shock to base frame. Apply Loctite 242 and torque to 160 in-lbs.
3G Storm Series ® Wheelchairs 126 Part No. 1104849 RWD WHEELCHAIRS SECTION 15 RWD WHEELCHAIRS 22NF BATTERIES (FIGURES 6 AND 7) 1. Remove the 22NF battery box. Refer to REMOVING/INSTALLING BATTERY BOXES in SECTION 9 of this manual. 2. Remove the drive wheel from the wheel hub.
Part No. 1104849 127 3G Storm Series ® Wheelchairs RWD WHEELCHAIRS SECTION 15 7. Secure the bottom of the NEW shock to the suspension arm with the existing mounting screw and locknut. Apply Loctite 242 and torque to 160 in-lbs. (FIGURE 6). 8. Install the drive wheel from the wheel hub.
3G Storm Series ® Wheelchairs 128 Part No. 1104849 RWD WHEELCHAIRS SECTION 15 GROUP 22 BATTERIES NOTE: Shock exploded away for clarity. There is no need to remove shock from suspension arm.
Part No. 1104849 129 3G Storm Series ® Wheelchairs REMOVING/INSTALLING GEARBOX (FIGURE 9 ) REMOVING 1. Remove the drive wheels from the wheelchair. Refer to REMOVING/INSTALLING DRIVE WHEELS in SECTION 12 of this manual. 2. Remove the drive wheel hub from the existing gearbox drive shaft.
3G Storm Series ® Wheelchairs 130 Part No. 1104849 ADJUSTING WEIGHT DISTRIBUTION (FIGURE 10) NOTE: Seat mount plates and seat support brackets allow the seat frame to be repositioned along the base frame. The range is determined by position of the seat stop screws.
Part No. 1104849 131 3G Storm Series ® Wheelchairs REPOSITIONING THE MOTOR REPOSITIONING THE MOTOR/GEARBOX (FIGURE 11) NOTE: The motor/gearbox assembly can be repositioned to lengthen or shorten the wheelbase by 2-inches in 1-inch increments. STANDARD POSITION - LENGTHENS the wheelbase and gives you the most stability and standard maneuverability.
3G Storm Series ® Wheelchairs 132 Part No. 1104849 REPOSITIONING THE STANDARD GEARLESS/BRUSHLESS MOTOR - BEFORE 1/26/04 (FIGURES 12 AND 13) NOTE: On models equipped with a fixed back only, the gearless/brushless motor can be repositioned to lengthen or shorten the wheelbase by 2-inches in 1-inch increments.
Part No. 1104849 133 3G Storm Series ® Wheelchairs 1. Determine the desired mounting position of the gearless/brushless motor. Refer to ACCEPTABLE MOUNTING POSITIONS FOR THE GEARLESS/BRUSHLESS MOTOR in this section of the manual. 2. Remove the 22NF battery box or group 24 battery boxes.
3G Storm Series ® Wheelchairs 134 Part No. 1104849 REPOSITIONING THE HEAVY DUTY GEARLESS/BRUSHLESS MOTOR (FIGURE 14) STANDARD POSITION - LENGTHENS the wheelbase and gives you the most stability and standard maneuverability. 1-INCH FORWARD - CENTERS the wheelbase and gives you standard stability and maneuverability.
Part No. 1104849 135 3G Storm Series ® Wheelchairs REPLACING SUSPENSION ARM FOR WHEELCHAIRS WITH MOTOR/GEARBOX ASSEMBLY (FIGURE 15) 1. Remove the drive wheels from the wheelchair. Refer to REMOVING/ INSTALLING DRIVE WHEELS in SECTION 12 of this manual.
3G Storm Series ® Wheelchairs 136 Part No. 1104849 RWD WHEELCHAIRS SECTION 15 RWD WHEELCHAIRS REPLACING SUSPENSION ARM FOR WHEELCHAIRS WITH GEARLESS/BRUSHLESS MOTORS (FIGURE 16) 1. Perform one (1) of the following: A. Remove the seating system. Refer to the Seating Systems Owner’s Manual for removal/ installation instructions.
Part No. 1104849 137 3G Storm Series ® Wheelchairs RWD WHEELCHAIRS SECTION 15 RWD WHEELCHAIRS ANTI-TIPPER WHEEL REPLACEMENT (FIGURE 17 ) 1. Remove the locknuts, hex screws and spacers that secure the anti-tipper wheels to the anti-tip bracket 2. Replace anti-tipper wheel(s) and torque existing hardware to 156 in-lbs.
3G Storm Series ® Wheelchairs 138 Part No. 1104849 NOTES NOTES NOTES.
Part No. 1104849 139 3G Storm Series ® Wheelchairs WARRANTY WARRANTY LIMITED WARRANTY For warranty information, please refer to the original owner’s manual which came with this product, or contact Invacare for more information.
Invacare Corporation www.invacare.com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Invacare, Yes, you can., the Medallion Elyria, Ohio USA Mississauga Ontario Design, Storm Series and Arrow are 44036-2125 L4Z 4G4 Canada registered trademarks of Invacare 800-333-6900 800-668-5324 Corporation.
Een belangrijk punt na aankoop van elk apparaat Invacare Arrow RWD (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Invacare Arrow RWD heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Invacare Arrow RWD vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Invacare Arrow RWD leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Invacare Arrow RWD krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Invacare Arrow RWD bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Invacare Arrow RWD kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Invacare Arrow RWD . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.