Gebruiksaanwijzing /service van het product HMV Highly 300 van de fabrikant Invacare
Ga naar pagina of 72
Owner’s Operator and Maintenance Manual DEALER: This manual MUST be given to the user of the scooter. USER: BEFORE using this scooter, read this manual and save for future reference. For more information regarding Invacare products, parts, and services, please visit www.
300 and 400 2 Part No. 1118395 WARNING POWERED SCOOTER USERS: DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOU T FIRST READING AND UNDERSTANDING THE OWNER’S OPERATOR AND MAINTENANCE MANUAL.
TABLE OF CONTENTS 300 and 400 3 Part No. 1118395 TABLE OF CONTENTS REGISTER YOUR PRO DUCT ................................................................ 6 SPECIAL NOTES ................................................................................
TABLE OF CONTENTS Part No. 1118395 4 300 and 400 TABLE OF CONTENTS Operating the Scooter ............... ............................... ................................ ............................ ..................30 Brake Release Lever...... .....
TABLE OF CONTENTS 300 and 400 5 Part No. 1118395 TABLE OF CONTENTS Removing/Installing the Caster Assemblies ........................ ............................... ............................... ..48 Removing ................ ......................
REGISTER YOUR PRODUCT 300 and 400 6 Part No. 1118395 Installing/Removing the Rear Mounted Basket .................................... ............................... ...............68 Installing .............. .........................................
Name _______________________________________________________________ Address _____________________________________________________________ City ___________________ State/Province __________ Zip/Postal Code ________ Email ___________________________________ Phone No.
Fold here Fold here Cut Along Line Invacare Product Registration Form Please Seal with Tape Before Mailing.
SPECIAL NOTES Part No. 1118395 9 300 and 400 SPECIAL NOTES W ARNING/CAUTION notices as used in this manual apply to hazards or unsafe practices which could result in personal injury or property damage. NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
TYPICAL PRODUCT PARAMETERS 300 and 400 10 Part No. 1118395 TYPICAL PRODUCT PARAMETERS *NOTE: 300 parameters ar e based on an 18-inch wide seat. *NOTE: 400 parameters ar e based on an 20-inch wide seat. 300 400 OVERALL DIM ENSIONS* BASE LEN GTH: BASE WI DTH: STEP HEI GHT (Floor Pan to Ground): SEAT HEI GHT (Floor Pan to Seat Cushion): 44 inches 22.
LABEL LOCATIONS Part No. 1118395 11 300 and 400 LABEL LOCATIONS ON 300 ! W ARNING Pinch P oint. 1079203 DO NOT oper ate the scooter unless the tiller is in the locked position. DO NOT lean against or pull f orward on the tiller while mounting or dismounting the scooter .
LABEL LOCATIONS 300 and 400 12 Part No. 1118395 ON 400 DO NOT oper ate the scooter unless the tiller is in the locked position. DO NOT lean against or pull f orward on the tiller while mounting or dismounting the scooter . Otherwise, injury may occur .
SECTION 1—GENERAL GUIDELINES Part No. 1118395 13 300 and 400 SECTION 1—GENERAL GUIDELINES WARNING SECTION 1 - GENERAL GUIDELINES contains important information for the safe operation and use of this product.
SECTION 1—GENERAL GUIDELINES 300 and 400 14 Part No. 1118395 DO NOT climb and/or go UP or DOWN ramps or traverse slopes greater than 8°. When negotiating ram ps, if the throttle co ntrol lever is released while in the FORW ARD motion, the pow ered scooter will roll back a pproximately one (1) foot before the brake engages.
SECTION 1—GENERAL GUIDELINES Part No. 1118395 15 300 and 400 Ensure that the seat is locked i n the FORWARD position b efore and during the operation of the scooter . Otherwise, injury to the u ser and/or damage to the scooter may result. DO NOT adjust the seat position outsid e the specifications recommended by the manufacturer .
SECTION 1—GENERAL GUIDELINES 300 and 400 16 Part No. 1118395 GROUNDING INSTRUCTIONS DO NOT , under any circumstances, c ut or remove the round grounding prong from any plug used with or for Inv acare products. Som e devices are equipped with three-prong (grounding) plugs for protection against possible shock hazards.
SECTION 1—GENERAL GUIDELINES Part No. 1118395 17 300 and 400 WEIGHT LIMITATION The we ight limitation for the 300 is 300 lbs. The we ight limitation for the 400 is 400 lbs. If so equipped, the front basket is rated f or a maximum loading capacity of 10 lbs.
SECTION 2—EMI INFORMATION 300 and 400 18 Part No. 1118395 SECTION 2—EMI INFORMATION WARNING CAUTION: IT IS VERY IMPORTANT T HAT YOU READ THIS INFOR MATION REGARDING THE POSSIBLE E FFECTS OF ELECTROMAGNETIC INTERFERENCE ON YOUR POWERED WHEELCH AIR.
SECTION 2—EMI INFORMATION Part No. 1118395 19 300 and 400 WARNING Powered Wheelchair Electromagn etic Interference (EMI) Because EM energy rapidly becomes more intense as one moves close r to the transmitting antenna (source), the EM fields from hand-held radio wave sources (transceivers) are of special concern.
SAFETY/HANDLING OF POWERED SCOOTERS 300 and 400 20 Part No. 1118395 SECTION 3—SAFETY/HANDLING OF POWERED SCOOTERS “Safety and Handling” of the powered scoot er requires the close attention of the user . This manual points out the most common proce dures and techniques involved in the safe operation and maintenance.
SAFETY/HANDLING OF POWERED SCOOTERS Part No. 1118395 21 300 and 400 Proper positioning is essential for your safety . STAIRWAYS WARNING DO NOT attempt to move an occupied powered scooter between floors using a stairway. Use an elevator to move an occup ied powered scooter between floors.
SECTION 4—SAFETY INSPECTION 300 and 400 22 Part No. 1118395 SECTION 4—SAFETY INSPECTION NOTE: Every six (6) months take your power ed sc ooter to a qualified technician for a t horough inspection and servicing. Regular cleaning will reve al loose or worn parts and enhance the smooth operation of your power ed scooter .
SECTION 4—SAFETY INSPECTION Part No. 1118395 23 300 and 400 ❑ Tighten locknut if the fro nt wheel wobbles noticeably or loosen locknut if the wheel binds to a stop. ❑ Ensure that the fork ste m bearing set is tight. ❑ Ensure that wheel bearings are clean and free of moisture.
SECTION 4—SAFETY INSPECTION 300 and 400 24 Part No. 1118395 INSPECT/ADJUST PERIODICALLY ❑ Ensure that the powered scooter drives straight (no excessiv e drag or pull to one side). ❑ Check frame for damage and corrosion. ❑ Ensure that the brake is eas y to engage/disengage.
SECTION 5—MAINTENANCE AND TROUBLESHOOTING Part No. 1118395 25 300 and 400 SECTION 5—MAINTENANCE AND TROUBLESHOOTING WARNING After ANY adjustmen ts, repair or serv ice and BEFORE use, make sure that all attaching hardware is tightened securely - oth erwise, injury or damage may occur.
SECTION 5—MAINTENANCE AND TROUBLESHOOTING 300 and 400 26 Part No. 1118395 FIGURE 5.1 - LUB RICATION POINTS TROUBLESHOOTING SYMPTOM PROBABLE CAUSE SOLUTION LIMITED D RIVING DISTANCE. Battery not charged long enough. Batteries weak, w on’t hold charge.
SECTION 6—OPERATION OF THE POWERED SCOOTER Part No. 1118395 27 300 and 400 SECTION 6—OPERATION OF THE POWERED SCOOTER CONTROL PANEL NOTE: For the following informati on, r efer to FIGURE 6.1 and FIGURE 6.2. 1. SPEED CONTROL KNOB - Located on the TOP face of the control panel.
SECTION 6—OPERATION O F THE POWERED SCOOTER 300 and 400 28 Part No. 1118395 FIGURE 6.1 - CONTROL PANEL 3. CHARGING INDICATOR - Located on the TOP face of the control panel as shown in FIGURE 6.1. Solid RED indicates the charger is on (plugged into w all receptacle).
SECTION 6—OPERATION OF THE POWERED SCOOTER Part No. 1118395 29 300 and 400 5. HEADLIGHT SWITCH - Located on the TO P face of the control panel of 400 only . Refer to Detail “B” of FIGURE 6.1. 6. ON/OFF KEY SWITCH - Located on RIGH T side of the control panel (FI GURE 6.
SECTION 6—OPERATION O F THE POWERED SCOOTER 300 and 400 30 Part No. 1118395 OPERATING THE SCOOTER WARNING After ANY adjustmen ts, repair or serv ice and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.
SECTION 6—OPERATION OF THE POWERED SCOOTER Part No. 1118395 31 300 and 400 NOTE: Throttle contr ol levers operate such that m oving one (1) will also move the opposite side throttle contr ol lever . 7. T o operate the scooter , depress the throt tle control lever in the following manner: A.
SECTION 6—OPERATION O F THE POWERED SCOOTER 300 and 400 32 Part No. 1118395 FIGURE 6.3 - BRAKE RELEAS E LEVER RESETTING THE CIRCUIT BREAKER WARNING NEVER def eat or bypass the circuit breaker. ONLY replace with a cir cuit breaker of the same rating.
SECTION 6—OPERATION OF THE POWERED SCOOTER Part No. 1118395 33 300 and 400 REPLACING THE FUSE WARNING NEVER defeat or bypass any fuse . ONLY replace with a fuse of the same rating. NOTE: For this procedur e, refer to FIGURE 6.5. 1. Remov e seat.
SECTION 7—SEAT 300 and 400 34 Part No. 1118395 SECTION 7—SEAT WARNING After ANY adjustmen ts, repair or serv ice and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result. Before performing any maintenance, adjustment or service, tur n power OFF and remove key from ignition.
SECTION 7—SEAT Part No. 1118395 35 300 and 400 REMOVING/INSTALLING THE SEAT POST WARNING Ensure that the seat post mounting screw is properly engaged and locked. Other- wise, injury and/or dam age may result. NOTE: T ake note of position and orientation of the seat post and seat post mounting screw befor e removing.
SECTION 7—SEAT 300 and 400 36 Part No. 1118395 ADJUSTING SEAT HE IGHT NOTE: For this procedur e, refer to FIGURE 7.2. 1. Remov e the seat. Refer to Removing/Installing the Seat on page 34. 2. Remov e the mounting screw , two (2) w ashers and locknut securing the seat post to the frame post.
SECTION 7—SEAT Part No. 1118395 37 300 and 400 FIGURE 7.3 - ADJU STING SEAT DEPTH 4. Adjust back assembly to one (1) of th ree (3) m ounting positions (FIGURE 7.3). 5. Reinstall the six (6) mounting screws se curing the back assembly to the seat b ase.
SECTION 7—SEAT 300 and 400 38 Part No. 1118395 NOTE: The seat locks in position at 90° intervals. The seat is locke d when an aud ible “click” is heard. 3. Rotate the seat to the desired position. 4. Release seat lev er to lock seat in desired position.
SECTION 7—SEAT Part No. 1118395 39 300 and 400 FIGURE 7.5 - REMOVING/INS TA LLING SEAT POSITIONING STRAP Seat Positioning Strap Washer Mounting Screw Seat Positioning Strap Washer Mounting Screw Arm.
SECTION 8—ARMS 300 and 400 40 Part No. 1118395 SECTION 8—ARMS WARNING After ANY adjustments, r epair or service and BEFORE use, make sure all attaching hardware is tightened securely - othe rwise injury or damage may result. Before performing any maintenance, adjustment or service, tur n power OFF and remove key from ignition.
SECTION 8—ARMS Part No. 1118395 41 300 and 400 CAUTION The arm can be adjusted to a maximum distance of 4½ inches from the inside of th e arm to the top of the mount ing shaft. If the ar m is adjusted beyond the m aximum 4½ inches, the arm will fa ll out.
SECTION 8—ARMS 300 and 400 42 Part No. 1118395 3. Reinstall the lock knob th at secures the arm to the arm m ounting tube and tighten securely . 4. Repeat STEPS 1-3 for opposite arm, if necessary . FIGURE 8.3 - ADJUST ING ARM HEIGHT REPLACING ARMREST PADS NOTE: For this procedur e, refer to FIGURE 8.
SECTION 9—TILLER ADJUSTMENT Part No. 1118395 43 300 and 400 SECTION 9—TILLER ADJUSTMENT ADJUSTING THE TI LLER ANGLE WARNING Before performing any maintenance, adjustment or service, tur n power OFF and remove key from ignition. Ensure that tiller is properly ad justed before driving the scooter.
SECTION 10—REAR SHROUD 300 and 400 44 Part No. 1118395 SECTION 10—REAR SHROUD WARNING After ANY adjustmen ts, repair or serv ice and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.
SECTION 11—WH EELS AND CASTERS Part No. 1118395 45 300 and 400 SECTION 11—WHEELS AND CASTERS WARNING After ANY adjustmen ts, repair or serv ice and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.
SECTION 11—WHEELS AND CASTERS 300 and 400 46 Part No. 1118395 FIGURE 11.1 - REMOVI NG/INSTALLING THE DRIVE WHEEL S WARNING: PINCH POIN T Cutout Drive Shaft Keystock Washer Hex Nut Drive Wheel Scoote.
SECTION 11—WH EELS AND CASTERS Part No. 1118395 47 300 and 400 REMOVING/INSTALLING THE FRONT WHEEL NOTE: T ake note of position and orientation o f wheel and mounting hard war e before r emoving. NOTE: For this procedur e, refer to FIGURE 1 1.2. REMOVING 1.
SECTION 11—WHEELS AND CASTERS 300 and 400 48 Part No. 1118395 REMOVING/INSTALLING THE CASTER ASSEMBLIES NOTE: For this procedur e, refer to FIGURE 1 1.3. REMOVING 1. Apply a wrench to the hex n ut on the caster assembly . 2. T urn the hex nut COUNTER-CL OCKWI SE to loosen and remove the caster wheel.
SECTION 12—BATTERIES Part No. 1118395 49 300 and 400 SECTION 12—BATTERIES WARNING Before performing any maintenance adju stment or service, turn power OFF and remove key from ignition. NEVER allow any of your tools and/or batter y cable(s) to contact BOTH batter y terminal(s)/post(s) at t he same time.
SECTION 12—BATTERIES 300 and 400 50 Part No. 1118395 NOTE: If ther e is battery acid on the rear frame or on the sides of the batteries, apply baking soda to these areas to neutralize the bat tery acid. Before reinstalling the new or existing batteries, clean the baking soda from the batte ry tray or batteries.
SECTION 12—BATTERIES Part No. 1118395 51 300 and 400 REMOVING NOTE: For this procedur e, refer to FIGURE 12.2. 1. Place the pow ered scoote r in a well v entilated area where work can be performed without risking damage to carpeting or floor cov ering.
SECTION 12—BATTERIES 300 and 400 52 Part No. 1118395 7. Connect the RED and BLACK battery connector to the wiring harness assembly . Tighten securely . 8. Secure batteries in the battery tray using the battery strap (Detail “ A” of FIGURE 12.2).
SECTION 12—BATTERIES Part No. 1118395 53 300 and 400 REMOVING/INSTALLING THE BATTERIES ON 400 NOTE: For this procedur e, refer to FIGURE 12.2. REMOVING 1. Place the pow ered scoote r in a well v entilated area where work can be performed without risking damage to carpeting or floor cov ering.
SECTION 12—BATTERIES 300 and 400 54 Part No. 1118395 FIGURE 12.3 - REMOVING/INSTALLING THE B ATTERIES ON 400 Battery Tray NOTE: Seat and Rear Shr oud not shown for clarity .
SECTION 12—BATTERIES Part No. 1118395 55 300 and 400 CONNECTING/DISCONNECTING THE BATTERY CABLES ON THE 400 WARNING On 400 only - Battery terminal configuration shown below MU ST be u sed. B atteries that have the reversed terminal configuration MUST NOT be used - otherwise serious injury or damage may occur.
SECTION 12—BATTERIES 300 and 400 56 Part No. 1118395 WARNING When connecting the battery cables to th e batteries, the battery cables MU ST be connected to the battery termin als/posts as shown in FIGURE 12.5, otherwise dam- age to the battery cable may result when installing battery terminal caps.
SECTION 12—BATTERIES Part No. 1118395 57 300 and 400 5. Slide terminal cap(s) UP on the battery cab le(s). 6. Disconnect battery cable(s) from battery(ies) term inal(s)/post(s): A. POSITIVE (+) RED battery cable from the POSITIVE (+) b attery terminal/post.
SECTION 12—BATTERIES 300 and 400 58 Part No. 1118395 CHARGING THE BATTERIES WARNING NEVER attempt to recharge the batteries by attaching cables directly to the battery terminals o r clamps. DO NOT attempt to recharge the batteri es and operate the powered scooter at the sam e time.
SECTION 12—BATTERIES Part No. 1118395 59 300 and 400 FIGURE 12.6 - CHARGING THE BATTERIES BATTERY CHARGER OPERATION - CHARGER INDICATOR LIGHT ON TILLER NOTE: If the scooter is turned on while char ging, the battery char ge indicator will show the batteries at FULL charge.
SECTION 13—TRANSPORTING 300 and 400 60 Part No. 1118395 SECTION 13—TRANSPORTING WARNING After ANY adjustmen ts, repair or serv ice and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.
SECTION 13—TRANSPORTING Part No. 1118395 61 300 and 400 FIGURE 13.1 - TRANS PORTING THE SCOOTER - 300 400 NOTE: For this procedur e, refer to FIGURE 13.2 . DISASSEMBLING 1. If installed on scooter , remove the front ba sket. Refer to Removing/Installing the Front Basket on page 64.
SECTION 13—TRANSPORTING 300 and 400 62 Part No. 1118395 A. Use the one hand to firmly hold the tiller handle. B. Using the other hand, firmly hold th e Y E LLOW frame lock lev er [located und er marker label # 2 ]and pull UP to the Unlocked position as shown in Detail “C” of FIGURE 13.
SECTION 13—TRANSPORTING Part No. 1118395 63 300 and 400 FIGURE 13.2 - TRANS PORTING THE SCOOTER - 400 1 2 2 1 2 Motor Connector Motor Connector BLACK Battery Connectors RIGHT Battery LEFT Battery Re.
SECTION 14—SCOO TER ACCESSORIES 300 and 400 64 Part No. 1118395 SECTION 14—SCOOTER ACCESSORIES WARNING After ANY adjustmen ts, repair or serv ice and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.
SECTION 14—SCOO TER ACCESSORIES Part No. 1118395 65 300 and 400 INSTALLING/REMOVING THE CRUTCH/CANE HOLDER NOTE: The Crutch/Cane Holder , Safety Flag and O xygen Holder all install into the accessory tube; ONL Y one (1) of these may be installed at a time.
SECTION 14—SCOO TER ACCESSORIES 300 and 400 66 Part No. 1118395 INSTALLING/REMOVING THE SAFETY FLAG NOTE: For this procedur e, refer to FIGURE 14.3. WARNING The installation of the safety flag on to the back of the scooter seat significantly increases the length of the scooter.
SECTION 14—SCOO TER ACCESSORIES Part No. 1118395 67 300 and 400 INSTALLING/REMOVING THE WALKER HOLDER NOTE: Reverse this pr ocedure to r emove the walker holder . NOTE: For this procedur e, refer to FIGURE 14.4. 1. If necessary , loosen but do not remove the mounting knob.
SECTION 14—SCOO TER ACCESSORIES 300 and 400 68 Part No. 1118395 INSTALLING/REMOVING THE REAR MOUNTED BASKET NOTE: For this procedur e, refer to FIGURE 14.
Part No. 1118395 69 300 and 400 NOTES.
300 and 400 70 Part No. 1118395 NOTES.
LIMITED WARRANTY Part No. 1118395 71 300 and 400 LIMITED WARRANTY PLEASE NOT E: THE WARRANTY BE LOW HAS BE EN DRAFTE D TO COMP LY WITH FEDERAL L AW APPLICABLE TO PROD UCTS MANUFACT URED AFTE R JULY 4, 1975. This warranty is extended only to the orig inal purchaser/user of our products.
Invacare Corporati on www.invacare.com USA One Invacare Way Elyria, Ohio USA 44036-2125 800-333-6900 Canada 570 Matheson Blvd E Unit 8 Mississaugua Ontario L4Z 4G4 Canada 800-668-5324 Invacare is a registered trademark of Invacare Corporation. Teflon is a registered trademark of E.
Een belangrijk punt na aankoop van elk apparaat Invacare HMV Highly 300 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Invacare HMV Highly 300 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Invacare HMV Highly 300 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Invacare HMV Highly 300 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Invacare HMV Highly 300 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Invacare HMV Highly 300 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Invacare HMV Highly 300 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Invacare HMV Highly 300 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
