Gebruiksaanwijzing /service van het product GWHDMS52 van de fabrikant IOGear
Ga naar pagina of 32
www .iogear .com User Manual W ir eless 5x2 HD Matrix GWHDMS52 P ART NO. M1229-b.
© 2014 IOGEAR ® Part No. M1229-b IOGEAR, the IOGEAR logo, are trademarks or register ed trademarks of IOGEAR. Microsoft and W indows ar e registered trademarks of Microsoft Corporation. All other brand and product names are trademarks or r egistered trademarks of their respective holders.
3 T able of Contents Important Information 4 Introduction 8 Package Contents 8 Requirements 8 Overview 9 Hardwar e Installation 12 Step 1: Setup the T ransmitter 12 Step 2: Setup the Receiver 13 Step .
4 Important Information Please take the time to read this user manual before using the T ransmitter and Receiver . It contains important information about operating your Full HD video wireless kit. Our limited warranty applies when the product is handled pr operly for intended use, in accordance with its operating instruction.
5 • Never use this product nearby an aircraft or medical facility . It can cause interference or undesirable ef fect on the operation result • Use of this product in the following locations may result in abnormal video and audio output (noise, blocked image.
6 CAUTION: Using the System in the US • Anychangesormodicationsnot expressly appr oved by the grantee of this device could void the user’ s authority to operate the equipment.
7 French translation: Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:.
8 Introduction IOGEAR’ sGWHDMS52W ireless5x2HDMatrixisthersttosendFulluncompr essedHD 1080p, connects up to 5 source devices and allow you to switch and independently select any source between 2 HDTVs.
2 3 1 2 3 1 4 5 6 9 Overview T ransmitter T op view 1. Sour ce LEDs These LED indicators are lit in solid gr een to show current input 2. Sour ce Selection Button Press to switch Sour ce inputs connected to the transmitter . 3. Power Button with LED Indicator Press to turn the transmitter on/off.
2 3 1 4 2 3 1 4 10 Receiver T op view 1. Power Button with LED indicator Press to turn the receiver On and Of f. The indicator in the power button lights up in green when the power is on, and turns red in standby mode. 2. Sour ce Button Press this button for Sour ce device input selection 3.
8 11 Remote Control 1. POWER ON / POWER OFF Buttons Press Power ON to turn the T ransmitter & Receiver ON. Press Power OFF to turn the T ransmitter & Receiver OFF . When both T ransmitter & Receiver Power LEDs are r ed, press Power ON to the Receiver to wake-up both the Receiver and T ransmitter automatically .
IR Blaster VCR HD Cable Bo x Blu-ray Pla yer HD Gaming Box Home PC HD Projector or HD Flat Panel TV 12 Hardwar e Installation Step 1: Setup the T ransmitter Connect up to 5 Audio / Video Source Devices and a HDTV to the transmitter: 1. Connect the supplied power adapter to the DC IN jack of the transmitter and a wall socket.
13 Step 2: Setup the Receiver HDTV Connection with receiver: 1. Connect the supplied mini USB power adapter to the DC IN jack of the receiver and a wall socket. The POWER LED indicator lights up in green when the receiver is connected to power . 2. Connect either a USB based Keyboar d or Mouse to the USB port on the back of the receiver .
14 Step 3: Setup the IR blaster extender cable and IR sensor extender cable The IR relays infrar ed commands from your remote control to your device. Users can control their A V devices by pointing their remote contr ol to the receiver or IR sensor extender cable.
15 Step 4: Mounting the Receiver to a W all (Optional) 1. Refer the drawing at right that has relative position of the main holes that will be needed to be drilled into the wall. 2. Drill two 1/4” pilot holes. 3. Insert the supplied two Anchors into the wall.
16 Basic Operation 1. After the power adapter is plugged into the electrical outlet, the device will turn ON automatically . 2. If the r eceiver is in Standby mode (POWER LED on the receiver is lit in red), press the POWER button ON to the receiver and then transmitter and r eceiver will establish link automatically .
17 4. During warm-up, the transmitter’ s and the receiver’ s wireless status LED will blink green until the signal link between the transmitter and the receiver is established. It will take approximately 15 ~ 20 seconds for system to fully boot-up successfully .
Note: Pressing “Up” or “Down” on r eceiver side or pressing “Left” or “Right” on transmitter side will not initiate switching. OSD Displayed: 18 B.
19 7. If operation is normal, the POWER/Wireless status LED and Sour ce Status LED will glow in solid green. Please r efer to the LED status table below that contains detailed LED indicator and OSD de.
ON HDMI1 CH1 1280x1024 = OFF HDMI1 CH1 1280x1024 HDMI1 CH1 1280x1024 = 47KHz HDMI1 CH1 1280x1024 = 56KHz 20 E. On Screen Display (OSD) vs. Remote Contr ol Instruction (1) In Active mode, press the POW.
2 1 * 21 (1) T ransmitter – Using a Mini USB to USB T ype A USB cable, Plug the mini USB side into the transmitter and the USB type A into the computer you wish to control. 8. USB HID Setup Instructions Y ou can conveniently control your computer connected to the transmitter from the r eceiver side wirelessly via the GWHDMS52 USB connections.
22 Advanced Operation Naming the Input Source Devices 1. Pr ess and hold the Source button on the top of transmitter for over 3 seconds. A source naming OSD will appear on the scr een: 2.
2 2 Wireless 5x2 HD Matrix Source 23 Pairing new transmitter with existing receiver (optional) Enter the Pairing mode for transmitter: 1. Unplug Power Adapter fr om the transmitter . 2. Pr ess and hold down the Power button on the transmitter . 3. Plug in Power adapter to the transmitter .
24 Multiple T ransmitter Selection 1. V erify that the power is removed from T ransmitter 1. Press T ransmitter No. key on the remote contr ol and point it at Receiver 1. OSD Displays: 2. Enter SETUP menu. OSD Displays: 3. Enter “Add New T ransmitter” menu if you would like to add a T ransmitter .
25 4. Enter “Remove T ransmitter” menu if you would like to remove a transmitter OSD Displays: 5. Enter “Modify T ransmitter Name” menu if you would like to modify a transmitter name OSD shows.
26 Supported Resolution If the SOURCE LED continues to blink in green (slower than “no signal” mode); OSD display: , and there is no video displayed or the video quality suf fers, it indicates that the video frame rate from your A/V sour ce device is not supported.
27 If the Source/Status LED continues to blink gr een (slower than “no signal” mode); or OSD display shows , please check that both TVs connected to the transmitter and receiver support 3D video format and try to switch the 3D video format to one of the 3D timings listed below .
28 Specications Supported Video Resolutions HDMI Input 3D, 1080p, 1080i, 720p, 576p, 480p Component Input 1080i, 720p, 576p, 576i, 480p, 480i Supported Audio Formats Digital Audio Up to 6 Mbps AC3 and DTS Analog Audio 48KHz and 24-bit Per Sample T ransmission Distance The maximum video transmission range is100ft (The minimum range is 6.
29 1. Problem: The power indicator LED doesn’ t light up. Solution: Check the power adapters of the T ransmitter/Receiver to see if they are properly inserted into a functioning power outlet.
30 4. Problem: No audio Solution: • Check your TV’ s volume is properly set and not set in “MUTE” mode. • Check if your source player’ s audio volume has been turned up.. • Ensure the bit rate of audio fr om the source device can be supported by GWHDMS52.
31 Federal Communications Commission (FCC) Statement Theuseriscautionedthatthisdeviceshouldbeusedonlyasspeciedwithinthismanualto meet RF exposure r equirements. Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions.
©2014 IOGEAR ®.
Een belangrijk punt na aankoop van elk apparaat IOGear GWHDMS52 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen IOGear GWHDMS52 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens IOGear GWHDMS52 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding IOGear GWHDMS52 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over IOGear GWHDMS52 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van IOGear GWHDMS52 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de IOGear GWHDMS52 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met IOGear GWHDMS52 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
