Gebruiksaanwijzing /service van het product LST0979-001B van de fabrikant JVC
Ga naar pagina of 32
OUTDOOR DOME CAMERA TK-C2201WPU (For USA and Canada) TK-C2201WPE (For Europe) INSTRUCTIONS . For Customer Use: Enter below the Serial No. which is located on the body. Retain this information for future reference. Model No. TK-C2201WPU,TK-C2201WPE Serial No.
Contents Introduction Contents ............................................................................................................. 2 Features ...................................................................................................
Thank you for purchasing this product. Before use, please read this "INSTRUCTIONS" and the information materials included to ensure proper use of this product. These instructions are for TK-C2201WPU/TK-C2201WPE. TK-C2201WPE is not evaluated by UL.
Operating Precautions m Storage and Location of Use v Do not install the camera in the following places. - In a place with vapor or oil, for example in a kitchen. - When the ambient temperature rises above or falls below the acceptable range (from -10 f to 50 f ) - In a place at which corrosive gases are emitted.
m Disclaimer v We will not be responsible for any inconveniences or disturbances caused in the event of privacy invasion as a result of camera footages of this product.
Name of Parts Camera . . A D E B C J K F H I G A Mounting Hole 2 2 ( A page 14) B Fall Prevention Wire Mounting Screw ( A page 14) C Conduit Plug/Hole (side) ( A page 21) D Dome Cover ( A page 13) E I.
G Protection Cover ( A page 15) H Power Supply Cable ( A page 11) ( A page 15) I Hole for Connecting Cables, Conduit Hole ( A page 20) J Base ( A page 19) K Dome Cover Fastening Screw 2 3 ( A page 13).
Name of Parts (Continued) Camera (Interior) The dome cover and inner dome are removed. . . D C H A B L 1 F ADJ MENU MONITOR SET MONITOR TYPE NOT USED DIPSW SEE INSTRUCTION MANUAL BLC OFF D/N AUTO CRT .
F Space for Inserting Heater When mounting the heater (sold separately: KA-ZH215U), read the instruction manual of the heater before mounting. G Power Supply Connector for Heater For connecting to the power supply connector of the heater.
About Connection Cables The maximum connection distance varies with the type of cable used. v Be sure to turn off the power of devices before connecting cables. . . To Power Supply To video Signal Cable Memo v Connect to AC 24 V power supply if using the heater (sold separately: KA-ZH215U).
DC 12 V or AC 24 V power supply cable Connect the power cord to the DC 12 V or the AC 24 V power supply. The unit is to be powered by a UL Listed Class 2 power supply only.
Setting the Switches Before mounting the camera, set the function setting switches on the camera. To set the switches, use a fine-tipped screwdriver. .
Mounting the Camera Selecting a mounting method v Mount directly to the ceiling or on the wall ( A page 13) v Mounting the Camera Using the Conduit Hole at the Bottom of the Base ( A page 19) v Mounti.
Mounting the Camera (Continued) m Mounting the Camera Unit 1 Make a hole ( Φ 30 mm) in the ceiling using the template provided 2 Mount the fall prevention wire for connecting the camera unit to the ceiling The fall prevention wire is not provided. Prepare a wire, taking into due consideration the length, strength, pull and material (insulating).
m Connecting the cable For safety reasons, turn on the power only after all the connection is complete. The status indicator lights up when the camera is turned on. 1 Connect the coaxial cable ( A page 10) Lower the protection cover and connect the connectors.
Mounting the Camera (Continued) m Process after connection Fill the conduit hole and mounting holes with sealing agent and insert the silica gel. 1 Fill the conduit hole and the screw mounted holes (2 locations) with sealing agent (GE silicon) Note Seal the holes completely.
m Adjusting images After mounting is completed, adjust the images while checking the actual image. ( A page 23) m Mounting the Dome Cover Attach the dome cover back when all settings are finished. 1 Mount the inner dome Mount the inner dome in a way that supports the tilt direction of the lens.
Mounting the Camera (Continued) 2 Mount the dome cover ① Clean the dust and dirt on the dome cover. ② Align the position marks (3 locations) on the camera unit and dome cover, followed by pressing in directly to mount the cover. ③ Tighten the dome cover fastening screw.
Mounting the Camera Using the Conduit Hole at the Bottom of the Base Conduit hole: G3/4-14 UNC (TK-C2201WPU), M25 (TK-C2201WPE) 1 Remove the dome cover and inner dome ( A page 13) 2 Remove the camera unit from the base and mount the fall prevention wire to the camera unit ① Loosen the camera unit fastening screw (2 locations) with a screwdriver.
Mounting the Camera (Continued) 3 Wind the sealing tape Wind the sealing tape around the pipe junction (where the conduit hole thread lines with the pipe screw hole) two or more times. 4 Mount the base to the pipe Turn and screw the base unit to the pipe in the clockwise direction.
Mounting the Camera Using the Conduit Hole at the Side of the Base If the camera cannot be mounted directly to the ceiling, use the conduit hole at the side of the base to mount the camera to the pipe.
Mounting the Camera (Continued) Mounting the Camera using the Electrical Box 1 Remove the dome cover and inner dome ( A page 13) 2 Mount the camera unit to the electrical box Mount the camera unit to the electrical box using the mounting hole (2 locations) with the M4 screw (2 pieces).
Adjusting Image After mounting the camera, adjust the images while looking at the actual image. Discharge the static electricity from your body by touching the metallic part of the monitor terminal before handling the camera as static electricity may cause the camera to malfunction.
Adjusting Image (Continued) 3 Adjust the shooting direction of the camera Adjust the camera for pan, tilt and rotation, and face the camera towards the subject.
4 Adjust the image size Loosen the fastening screw for the zoom adjustment ring and move the ring to the left/right to adjust the image size. After adjustment is complete, fasten the screw. 5 Adjust the focus ① Hold the focus adjust gear knob, shift the catch from point A to point B as illustrated in the diagram to disengage the gear.
Adjusting Image (Continued) 6 Fine adjust the focus ① Press and hold the [ J ] button. v Focus adjust mode will be activated and "FOCUS ADJUST MODE" is displayed on the monitor screen. v The contours are emphasized as the iris opens and the depth of field becomes shallow.
7 Tighten the fastening screw of the focus adjustment ring Hold and press the focus adjust gear between your fingers in the direction of the arrows in the diagram, and tighten the fastening screw of the focus adjustment ring.
Adjusting the Auto White Balance Each light source has its own color temperature. Therefore, when the main light source lighting the subject is changed, adjust the white balance again. 1 Press the [MENU] button. 2 Select [WHITE BALANCE] with the [ J / K ] button and "AWC" with the [ H / I ] button, then press the [SET] button.
Specifications Horizontal resolution : 550TV lines (typical) Video S/N ratio : 52 dB (typical, AGC OFF) Minimum illumination : Color mode: 0.05 lx (typical, 50 %, F1.2, AGC HIGH) Black and White mode: 0.03 lx (TK-C2201WPU) (typical, 50 %, F1.2, AGC HIGH) 0.
Specifications (Continued) Accessories : (TK-C2201WPU) WARRANTY CARD 2 1 INSTRUCTIONS 2 3 Silica gel 2 1 Wrench 2 1 Template 2 1 (TK-C2201WPE) INSTRUCTIONS 2 5 Silica gel 2 1 Wrench 2 1 Template 2 1 O.
m External dimensions [Unit: mm (inch)] . . 121(4-3/4) 113(4-1/2) 160(6-1/4) 9 5(1/4) 42(1-5/8) 125(4-7/8) 160(6-1/4) SR53.7 (3/8) Screw f or conduit (bottom surface , side surface) (TK-C2201WPU: G3/4-14 UNC, T K -C2201WPE: M25) (2-1/8) * Specifications and appearance of this camera are subject to change for improvements without notice.
TK-C2201WPU/ TK-C2201WPE OUTDOOR DOME CAMERA Q 2009 Victor Company of Japan, Limited LST0979-001B.
Een belangrijk punt na aankoop van elk apparaat JVC LST0979-001B (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen JVC LST0979-001B heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens JVC LST0979-001B vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding JVC LST0979-001B leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over JVC LST0979-001B krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van JVC LST0979-001B bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de JVC LST0979-001B kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met JVC LST0979-001B . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
