Gebruiksaanwijzing /service van het product 840091 van de fabrikant Kawasaki
Ga naar pagina of 20
MODEL #840091 FOR CUSTOMER SERVICE POUR LE SERVICE APRÉS VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1-800-590-3723 Printed in China 87-1904-60957 KAW ASAKI™ IS A TRADEMARK LICENSED BY KA WASAKI™ MOTORS CORP ., U.S.A., WHICH DOES NOT MANUF ACTURE OR DISTRIBUTE THIS PRODUCT .
USING THE DRILL PRESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 DRILLING WOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-30 DRILLING MET AL . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS READ AND UNDERST AND ALL INSTRUCTIONS. Failure to follow all instruc- tions listed below may result in electric shock, fire and/or serious personal injury . KEEP GUARDS IN PLACE AND IN WORKING ORDER.
This drill press is equipped with a grounded 3-wire power cord with a 3-prong plug. If the power cord will not fit into the wall plug, an approved adapter can be used as long as it is connected to the center screw in the wall plate. See Figure 1 and the steps below to use an AC grounding adapter: 1.
USE ONL Y DRILL BITS, SANDING DRUMS, AND OTHER ACCESSORIES that are designed for the various speeds of this drill press. The drill bits, sanding drums and other accessories should have a shank size 1/2" OR SMALLER. Unsuitable drill bits can break without warning throwing fragments outward at high speeds possibly causing severe injuries.
SECURE THE ELECTRICAL POWER CORD when the drill press is not in use to prevent unauthorized use of the tool and/or to prevent children from acciden- tally turning it on. ADDITIONAL INFORMA TION about the proper use of bench-mounted drill presses is available from the Power T ool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www .
FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS: 1. Column Base 2. Column Assembly 3. Column 4. Column Rack 5. T able Crank 6. T able Support 7. T able Crank Assembly 8.
T o minimize crank handle backlash, tighten the support lock, rotate the elevation worm shaft clockwise, assemble the crank tightly against the table support and tighten setscrew . 11.Check column collar for proper adjustment. 12.Collar should not be aligned on the column.
INST ALLING THE HEAD ASSEMBL Y The Head Assembly weighs approximately 55 pounds. Use caution when lifting it onto the column assembly . It is recommended that two people lift the head assembly onto the column. 1. Remove and discard the protective bag from head assembly .
18 17 INST ALLING THE CENTER PULLEY The head assembly contains three pulleys. The first pulley is on the is on the spindle shaft and the third pulley is on the motor shaft. The center pulley acts as an idler pulley making the installation and remo val of belts easi er .
SQUARING THE WORKT ABLE The combination square must be “true” when used to square the worktable. See T ools Required for Assembly . This is essential in order to do precision drilling. 1. Insert a straight, ground steel rod, approxi- mately 3" long (not included) into the drill check and tighten.
NEVER OPERA TE LASER IF THE UNIT IS DEFECTIVE OR THE COVER OR SEAL IS DAMAGED. DO NOT SERVICE LASER. The laser unit must be returned to the factor y for any service or repair . Service or repair must be handled by authorized factory trained technicians.
It is recommended that an approved ANSI full-face shield, that is impact resistant, be worn during all drill press operations. Should the full-face shield not be available, approved ANSI safety glasses with impact resistant lenses and side shields MUST be used as a substitute.
9. Grasp the feed handles and rotate them toward the front of the drill press low- ering the drill bit onto the workpiece. This step is necessary to ensure the hole will be where it is intended. Make any adjustments necessary . 10.Plug the drill press power cord into the AC power source.
SETTING THE DRILLING DEPTH ADJUSTMENT T urn t he dril l pre ss ON/O FF switc h to t he OFF posit ion a nd dis con nec t the AC powe r to pre ven t dril l pr ess from ac cid ent all y tur nin g on. The drilling depth adjustment is used when more than one hole is to be drilled to exactly the same depth (i.
DRILLING THROUGH WOOD: 1. Position the workpiece so that the hole to be drilled is over the center hole on the worktable. 2. Place a piece of scrap material under the workpiece to prevent “splintering” on the bottom side of the workpiece. 3. Clamp BOTH the workpiece and the scrap material to the worktable.
TROUBLE PROBABLE CAUSE SOLUTION When drilling metal, it is a good practice to keep the workpiece lubricated. This prevents galling and eventual seizing of the drill bit. Some drill bit models have accessories that automatically lubricate the metal workpiece.
SPECIFICA TIONS SPECIFICA TIONS Voltage 120V 60 Hz Rated Current 7.8 A No-Load Speed (motor) 1700 RPM Max. Distance From Spindle Axis T o Surface Of Column: 7 3/4" (197mm) Max.
found to be defective and subject to warranty . Alltrade retains the sole discretion to determine whether any item or part is nonconforming and, if so, whether the item and/or part will be repaired and/or replaced. If the unit is repaired, new or reconditioned replacement parts may be used.
REPRESENT A TIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. IN NO EVENT , WHETHER AS A RESUL T OF A BREACH OF CONTRACT , WAR R AN TY , T ORT (I NC LU D IN G NE GL I GE NC E) OR O TH E RW IS E, SH AL L ALL TRADE’S AND/OR ITS REPRESENT A TIVE(S)’ LIABILITY EXCEED THE PRICE OF THE PRODUCT .
Een belangrijk punt na aankoop van elk apparaat Kawasaki 840091 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Kawasaki 840091 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Kawasaki 840091 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Kawasaki 840091 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Kawasaki 840091 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Kawasaki 840091 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Kawasaki 840091 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Kawasaki 840091 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
