Gebruiksaanwijzing /service van het product 16238 van de fabrikant Kenmore
Ga naar pagina of 32
Assembly and Operation ® Liquid Propane Gas Grill Model No. 16238 @ @ I// THIS GRILL IS FOR OUTDOOR USE ONLY CAUTION Read and follow all Safety Statements, Assembly instructions, and Use and Care Manual Directions before attempting to assemble and cook.
Warranty ......................................................... 2 Safety. ............................................................. 2 Caring for your equipment .............................. 3 Hardware ..........................................
1 For residential use only. Do not use forl commercial cooking, I CARBON MONOXIDE HAZARD Combustion byproducts include carbon monoxide which has no odor and can cause serious injury or death.
L.P. GAS CYLINDER Gas cylinders manufactured today have mechanisms to provide worry free grilling year round: Q.C.C.I or Type 1-Quick Connect Coupling Valve, ensure fast tank hook-ups requiring only hand tightening. The redundant valve system inhibits the flow of gas to the burner if the connection is not correct.
2. TRANSPORTATION AND STORAGE: WARNING: Although it is safe when used properly, careless handling of the propane gas cylinder could result in fire, explosion, and/or serious injury.
bJ J #2 Phillips Screwdriver (! piece) : r_._ illivc#_._ ii & #8-32 x 3/8 Tapping Screw (2 pieces) & #10 x 1F2 Phillips Screw (24 pieces) Master Bagpack i i i i i i i i i i i i i i i i i i i i.
I'l No Tank Bracket % / Left hand leg assembly Tank Bracket Right hand leg assembly Notch Caster Plug FIG. "A" 1. Turn leg assembly upside down as shown and insert caster plug. Make sure caster plug tab is in line with notch in leg. (SEE FIG "A") 2.
5. Position left hand leg assembly as shown with console mounting tab facing up. Place non-tank side of bottom pan over bottom support. Attach bottom pan with 1/4"-20 x 1/2" carriage bolt (Black) and wing nut (Black). Console mounting tab facing up.
7. Position side panels over legs and slide up into position. Bottom flange of side panel hooks over bottom support. Push against leg assembly Then slide up into position.
Your Home For repair-in your home -of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
10. Position console/valve assembly over tabs as shown. Locate Console on tabs as shown. (Right side shown) Note: Check wires from switch harness to ensure that they are not against any sharp surfaces.
11. Assemble shelf support brackets by sliding shelf bracket (A) and Shelf bracket (B) together while paying close attention to hole alignment, and attach the two with (2) #10 x 1/2" screws.
14. Position left side shelf over shelf mounting brackets 15. To begin installation be sure to align large shelf (holes) with the small holes in the shelf bracket assembly. Insert (2) #10 x 1/2" Truss head screws (phillips drive) into largest hole on outside rear corner of shelf carefully aligning with small hole in shelf mounting bracket.
? 18. Attach side burner lid handle, side burner lid and burner tray. 19. First begin by attaching side burner lid handle to side burner lid using (2) #10 x 112" screws.
Front View Rear View Front View 22. Attach side burner assemblies using shelf mounting procedures as previously described. (Steps 14 & 15) 23. After attaching side burner base assembly to shelf mounting brackets insert side burner valve into burner tube of side burner as shown.
Attach side burner valve andbezel using (2) #8 x 3/8 tapping screws as shown. Insert side burner knob. #8 x 3/8 _, Tapping Screws J Knob Front View 25. Position base casting down over 1/4"-20 studs and secure in place with two 1/4"-20 large body wing nuts.
26. Position bottom cross lighter assembly as shown, being sure to feed ignitor wires through the front holes in the bottom of the base casting. Bottom cross-lighter just "lays" loose at this stage of the assembly. NOTE: Cross lighter top and cross lighter bottom assembly come packaged togetherwith the grill burners.
27. Install burners by feeding burner though slotin thebase casting and guiding burner tube over orifice in valve, see illustration below. Secure burners with three 1/4"-20 x 3/4" carriage bolts and 1/4"-20 Knurl nuts. Burner Tube Orifice Burner tube must fit over valve orifice as shown.
28. Install three cross lighter spacers over threaded studs in bottom cross lighter, then install cross lighter top plate. Secure with three #10-24 wingnuts. Tabs in cross lighter top must fit into "grooves" on top of burners as shown in illustration below.
29. Install Heat Distribution Plate by placing in position so thatthe sixsupports rest on the six ribs in the base casting. Suppo_ I I I I I I Rib in Base Casting 20.
30. Install Lid,Overlay, Handle, Cooking Grid, Warming Rack, Hinge Clip, andLogo. Install lid before installing overlay, logo, and temperature gauge. 1. Install lidandhinge clipas shown. 2. Place overlay on top of lid 3. Attach logo NOTE: Tighten wing nuts securely.
31. Install grease tray from rear of grill by sliding grease tray in on support rails until the frontof the traydrops down over the front of thesupport rails.
32. Attach the two wires from the cross lighter and the two wires from the side burner to any of the four small terminals on ignitor module as shown. Next, Attach the two wires from console assembly to the two large terminals on ignitor module as shown.
35. Place tank into hole located in bottom plate. Insert Tank Bracket into Slot and rotate it 90 Degrees. Slide bracket down over tank ring to hold tank in place, 36. Connect regulator withtank valve. Be surethat hose assembly does not contact the base casting or any other parts which will gethot.
Warning: Before proceeding with the following steps, ensure you have read the L.P. Gas Cylinder hose and Regulator sections of this Assembly and Operation Manual.
BREAKING IN YOUR GRILL Before cooking on your gas grill for the first time, you should "break it in" by operating it for a short period of time without any food. To "break in" your grill light the grill following the lighting instructions as outlined on the console decal or in this manual.
To keep your grill working at its peak efficiency as well as contribute to the safe operation of this unit, perform all of the operations below at least once a year -- preferably at the start of each cooking season. PERFORM A LEAK TEST A leak test ensures that there are no gas leaks prior to lighting your grill.
It is possible that very small insects could make webs or nest in the venturi tubes. This will partially or completely block the flow of gas through the venturi and is indicated by a smoky yellow flame, and/or a burner that is difficult or impossible to light.
Kenmore Propane Gas Grill REF # 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. 58.
Kenmore Propane Gas Grill :_i.4 :Jlie] J] :1JlvA I :W / 30.
1. Burners will not light. Out of propane? Is venturi properly seated over orifice? Inspect both venturis and burner holes for obstructions. Check ignition spark, ts cylinder valve turned on? Regulator assembly not fully tightened to cylinder valve? If you have electronic ignitor, is the battery good? 2.
Your Home For repair-in your home -of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
Een belangrijk punt na aankoop van elk apparaat Kenmore 16238 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Kenmore 16238 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Kenmore 16238 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Kenmore 16238 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Kenmore 16238 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Kenmore 16238 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Kenmore 16238 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Kenmore 16238 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
