Gebruiksaanwijzing /service van het product TK-8150 van de fabrikant Kenwood
Ga naar pagina of 23
TK-7150 INSTRUCTION MANUAL VHF FM TRANSCEIVER © B62-1619-10 (K) 09 08 07 06 05 04 03 02 01 TK-8150 UHF FM TRANSCEIVER SCN SP OP OS AB MON CALL.
T HANK Y OU We are grateful you chose KENWOOD for your personal mobile applications. W e believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency . KENWOOD transceivers incorporate the latest in advanced technology .
i ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine or imprisonment or both.
ii CONTENTS UNP ACKING AND CHECKING EQUIPMENT ................................................ 1 S UPPLIED A CCESSORIES ................................................................................. 1 PREP ARA TION .................................
1 UNP ACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD dealer , an authorized KENWOOD service facility , or the factory . Carefully unpack the transceiver . We recommend that you identify the items listed in the following table before discarding the packing material.
2 V arious electronic equipment in your vehicle may malfunction if they are not properly protected from the radio frequency energy which is present while transmitting. Electronic fuel injection, anti-skid braking, and cruise control systems are typical examples of equipment that may malfunction.
3 I NST ALLING THE T RANSCEIVER For passenger safety , install the transceiver securely , using the supplied mounting bracket, so the transceiver will not break loose in the event of a collision. 1 Mark the position of the holes in the dash by using the mounting bracket as a template.
4 ORIENT A TION F RONT P ANEL AND M ICROPHONE q q q q q V olume Control Rotate to adjust the volume level. Clockwise increases the volume and counterclockwise decreases the volume. w w w w w Display (See page 5.) e e e e e Selector Rotate to select a zone or channel/group ID.
5 !0 !0 !0 !0 !0 PF5 Key Press this key to activate its programmable auxiliary function {page 7}. The default setting is None. !1 !1 !1 !1 !1 PF6 Key Press this key to activate its programmable auxiliary function {page 7}. The default setting is None.
6 R EAR P ANEL 6-pin connector (for accessories) Power input connector Antenna connector 25-pin connector (for accessories).
7 PROGRAMMABLE AUXILIARY FUNCTIONS Keys y to !1 {pages 4 and 5} can be programmed with the auxiliary functions listed below . The keys can only be programmed with functions, depending on whether you are using a Conventional Group or a T runking System.
8 BASIC OPERA TIONS O PERA TION O VERVIEW Y our dealer can program your transceiver with T runking Systems and Conventional Groups. T runking Systems can handle 32 zones with up to 250 group IDs. Conventional Groups can handle up to 128 zones with up to 128 channels.
9 TRUNKING ZONES P LACING A D ISP A TCH C ALL 1 Select the desired trunking zone and a group ID. 2 Press and hold the PTT switch. 3 If the “Clear to T alk” tone sounds, communication is possible; start speaking into the microphone. Release the PTT switch to receive.
10 CONVENTIONAL ZONES T RANSMITTING 1 Select the desired conventional zone and a channel. • Make sure the channel is not in use. When a channel is in use, the BUSY (green) LED will light. 2 Press and hold the PTT switch, then speak into the microphone in your normal speaking voice.
11 SCAN To activate the Scan function, press the key programmed as Scan . • The SCN icon lights and “-SCAN-” appears on the display . To stop scanning, press the Scan key again. • The transceiver returns to the channel that was selected before Scan started.
12 DTMF CALLS Note: To make DTMF calls, you must have an optional microphone with a DTMF keypad. M ANUAL D IALLING Press and hold the PTT switch, then enter the digits on the microphone keypad.
13 C LEARING S TORED DTMF N UMBERS 1 Press and hold the microphone # key for 1 second. • “D” appears on the display . 2 P ress the # key again. • “D–CLEAR” appears on the display . •T o cancel the process, press any key other than 0 ~ 9 .
14 FleetSync™: ALPHANUMERIC TWO-W A Y PAGING FUNCTION FleetSync™ is an Alphanumeric T wo-way Paging Function, and is a protocol owned by KENWOOD Corporation. FleetSync™ enables a variety of paging functions on your transceiver , some of which depend on dealer programming.
15 O PTIONAL F EA TURES Short Messages: Received short messages (maximum of 48 characters) are displayed the same as Status messages {page 16}, however only 4 short messages can be stored in the stack memory . “M” (Message) and the message number appear with the message.
16 ■ Identification Codes An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number . Each transceiver must have its own Fleet and ID number . • Enter a Fleet number (100 ~ 349) to make a group call. • Enter an ID number (1000 ~ 4999) to make an individual call in your fleet.
17 ■ Receiving The mail icon ( ) will flash and a calling ID or text message will appear when a Status call is received. • The display alternates between the caller ID and the message.
18 ADV ANCED OPERA TIONS T IME - OUT T IMER (TOT) The T ime-out T imer prevents any single caller from using a channel for an extended period of time. If you continuously transmit for a period of time that exceeds the programmed time, the transceiver will stop transmitting and an alert tone will sound.
19 E MERGENCY O PERA TION Press and hold the key programmed as Emergency to enter Emergency Operation. • The duration you need to hold the key depends on how your transceiver has been set up. • The transceiver will switch to the pre-programmed emergency channel/ group ID.
Een belangrijk punt na aankoop van elk apparaat Kenwood TK-8150 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Kenwood TK-8150 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Kenwood TK-8150 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Kenwood TK-8150 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Kenwood TK-8150 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Kenwood TK-8150 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Kenwood TK-8150 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Kenwood TK-8150 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
