Gebruiksaanwijzing /service van het product 3186523 van de fabrikant KitchenAid
Ga naar pagina of 24
HOME APPLIANCES Installation Instructions Create-a-Cooktop Part No. 3186523 Rev. D Important: Installer: Leave Installation Instructions with the homeowner. Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use.
Minimum cabiret width above one appliance: g?$y;f - ‘2 - IMPORTANT: Observe all governing codes and ordinances. Downdraft vent - 6’ For each additional appliance combined with the first appliance, add the minimum cabinet width for that appliance. cabinet depth 1 /Electric - 1” min.
Before vou start... Proper installation iz your responsibility. Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with the installation clearances specified on the model/serial rating plate.
Product/cutout Dimensions Single Installations - One product per cutout Electk$;dpsGas Electk$;dpsGas Electric Grill I- 13-l 5/l 6” .-d -1. 21314” i WARNING: To reduce the risk of fire, electric s.
Combinations - When installing cooktops, grills and downdraft vents in the same cutout, use the following width dimensions: I Combination 2 cooktops I 3 cooktops I 4 cooktops 1 cooktop and 1 downdraft vent I 2 cooktops and 1 downdraft vent I 3 cooktops and 2 downdraft vents I Cutout Width 35” min.
Tools/Parts Electric Cooktop and Grill Tools and materials needed for installation: Electric cooktops and grills I Ll Gas cooktops pipejoint compound measuring tape/ruler’ Downdraft vents l Phillips.
Electrical connection This appliance is manufactured with a frame- connected, green or bare, ground wire. Connect the appliance cable to the junction box through the U.L.-listed conduit connector. Complete electrical connection according to local codes and ordinances.
Electric Cooktop and Grill (cont.) Now start... With cooktop and/or grill in kitchen. If installing more than one appliance in the same cutout, work with one appliance at a time. Start with the appliance that will be to the left side of the cutout. Make all adjustments; then follow steps to add adjacent appliances.
Do Not overtighten screws. glass cooktop countertor, 3. n 5/16” clamping 7 bracket screw One cooktop or grill in cutout: Rotate the mounting brackets away from the burner box. Tighten the mounting brackets to the burner box. Insert the 2-l/2” clamping screws into the mounting brackets.
Downdraft Vent Electrical requirements WARNING: To reduce the risk of fire, electric shock and injury to persons, the downdraft vent system must be installed with either the KitchenAid Model KPED890T exterior mounted motor unit or the KitchenAid Model KPID850T interior mounted motor unit.
Venting requirements Ductwork needed for installation is not supplied. Wall cap is provided with interior mounted motor. Fire Hazard Venting system MUST terminate to the outside. Do Not terminate the ductwork in an attic or other enclosed space. Do Not use 4-inch laundry-type wall caps.
Downdraft Vent (cont.) Exterior mounted vent motor installation methods To install ductwork under a concrete slab, see Insert Sheet. Do not install exterior vent motor in a window well. Island location Figure 5 Interior wall location Figure 6 Roof venting Figure 7 One exterior power vent motor can be used to operate two downdraft vent systems.
Now start . . . . 0 1 Place cardboard or other form of . protection on top of a flat surface where you can easily assemble the downdraft vent system. Remove downdraft blower box and motor section from cartons. Remove any shipping materials, tape and protective film from downdraft blower box and motor.
Downdraft Vent (cont.1 If downdraft vent is installed next to another aDr>liance in the same cutout, go to Step 11. If downdraft vent will be installed in a separate cutout (no other appliances in same cutout), remove the motor from the blower box.
other brown wire to the other capacitor terminal. Replace the rubber cap over the top of the capacitor. Put the capacitor into the mounting bracket on the lower section of the wiring box. the front of the blower box under the control using the four screws removed in Step 3.
Downdraft Vent (cont.) Exterior roof-mounted system requires Roof Mount Kit, Part No. 4173296. 0 1 . Place cardboard or other form of protection on top of a flat surface where you can easily assemble the downdraft vent system. Remove downdraft blower box and motor sections from cartons.
Position the downdraft vent cover so that it is aligned with light pencil marks made on the countertoo in Step 6. Use screws to attach legs to cabinet floor. Check that blower box is vertical. (Adjust legs until blower box is vertical.) Tighten screws that attach the legs to the blower box.
Downdraft Vent (cont.) wire lg black i wires conduit connector 117. Power supply wiring is not provided. motor cable Thread the power supply cable through the conduit connector. Tighten the screws on the conduit connector. Disconnect power supply. Connect the two white wires together with twist- on wire connector.
Sealed Gas Cooktop Gas supply requirements Explosion Hazard Use a new AGA approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure gas pressure does not exceed water column rating specified in LP conversion kit.
Sealed Gas Cooktop (cont.) Electrical requirements Electrical Shock Hazard Plug into a grounded 3-prong outlet. Do not remove ground prong. Do not use an adapter.
To avoid scratching countertop, lift entire If you are installing additional appliances in the cooktop up from cutout when repositioning same cutout, attach one mounting bracket to the cooktop into countertop opening. right side of each additional appliance.
Sealed Gas Cooktop (cont.) Multiple cooktops and/or grill combinations: Rotate the left mounting bracket away from the burner box of the first appliance. Tighten the mounting bracket to the burner box. Insert the 2-l/2” clamping screw into the mounting bracket.
Plug the power supply cord into the grounded outlet. 115.1 Place burner grates over burners and caps. Install control knobs on valve stems. Electronic Ignition System - initial lighting b-l n Push in and turn each control knob Cooktop burners use electronic ignitors in place of standing pilots.
. W iring diagram Part No. 3186523 Rev. D 0 1998 KitchenAid @ Registered Trademark of KitchenAid, U.S.A. If the cooktop, grill or downdraft vent does not operate... l Check that the circuit breaker is not tripped or the house fuse blown. l Check that the power supply cord is plugged into outlet.
Een belangrijk punt na aankoop van elk apparaat KitchenAid 3186523 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen KitchenAid 3186523 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens KitchenAid 3186523 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding KitchenAid 3186523 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over KitchenAid 3186523 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van KitchenAid 3186523 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de KitchenAid 3186523 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met KitchenAid 3186523 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
