Gebruiksaanwijzing /service van het product VIDEOMATE 2030P van de fabrikant Kodak
Ga naar pagina of 18
V IDEO M ATE 2030/2030 P Video Slide Projector Instruction Manual The W orld Leader in Image Quality.
2 Table of Contents 3 Product Overview 4 Safety Precautions 5 Voltage Selection 7 Installation 9 Slide Tray Installation 1 1 Lamp/Fuse Replacement 1 3 Troubleshooting 1 5 Specifications 1 6 Appendix 1.
3 Product Overview Product Overview Universities, boardrooms, and conventions have the common goal of effective information communication. T oday’ s individual is continually being bombarded by sophisticated media presentation. T o compete ef fectively for his attention (and retention) one must utilize similar techniques.
4 7 Safety Precautions Safety Precautions For safety , before connecting the projector to the main, ensure that the voltage selector is set to your main voltage and the required fuse is fitted. An incorrectly adjusted main voltage can damage the projector .
5 Voltage Selection Voltage Selection Check voltage setting. The Navitar VideoMate will be exported throughout the world to countries with differing mains voltages. The projectors are already set during manufacture to a fixed main voltage. 100-200V mains: Shipments to countries with 100 or 200V mains will be equipped with a 5A fuse.
6 V oltage Selector Tray Positioning Index Mark Lock Ring Alignment Mark Fuse Holder Voltage Selection.
7 Installation Installation Before installing please review precautions. For those users familiar with both the operation of 35mm slide projector and their own video displays, the following is an abbreviated start-up procedure. 1. Check the voltage setting before powering on.
8 Installation 9. T o shut down the system, hold down the select bar and rotate the slide tray to the “0” index position. Set the power switch to “off”. 10. For instructions regarding setting up slide tray changing lamps, etc., refer to the appropriate section of the manual.
9 Slide Tray Installation Slide Tray Set-Up This system was designed to permit usage of prepared presentations without reorientation of the slides in the tray . Y our new Navitar VideoMate will accept Kodak Ektapro 80, Kodak Ektagraphic 80 for holding 80 slides with a maximum slide mount thickness of 3.
10 Slide Tray Installation Slide Tray Removal T o remove the tray from the projector without losing slides: 1. Hold the selector bar down and rotate the tray back to the zero index position. 2. Lift the tray at a point opposite the index mark. Slide Tray Jam The tray may jam if a damaged slide is caught in the gate.
11 Lamps/Fuse Replacement Lamps The VideoMate will function with either of the following 82 volt or 85 watt lamps. One provides a higher color temperature, with the other exhibits a much longer life. Do not use 82 volt, 25-300 watt slide projection lamps or your equipment will suffer severe damage.
12 4. Reverse the procedure to insert a new lamp (make sure the new lamp is properly seated). 5. Lock the new lamp in place with wire bail. Fuses Always switch off the projector and unplug the main lead before replacing a fuse. Avoid the risk of fire, replace only with a fuse of same type and rating.
13 Troubleshooting Troubleshooting Symptom #1: After switching on, projector is not operable. Possible Cause: 1. All equipment not “powered up”. Check outlets and individual unit (monitor , video projector , etc.). 2. Check input voltage selector .
14 Symptom #4 Image too dark or too light. Possible cause: 1. Illumination level inadequate. Set knob “I” as required. 2. Monitor not adjusted properly . Symptom #5 Image not sharp. Possible cause: 1. Adjust focus knob. 2. Illumination level is too high or too low .
15 s n o i t a c i f i c e p S a r e m a C e c i v e D p u - k c i PD C C r e f s n a r T e n i l r e t n I " 2 / 1 t n u o C l e x i P) V ( 2 8 5 x ) H ( 2 5 7 r e t l i F r o l o Cc i a s o M r.
16 Appendix Appendix Due to transportation, the image position might shift from the factory setting. T o correct this shift: 1. Remove the two plugs as shown in the figure below: 2. Using the Phillips screw driver , rotate screw #1 to adjust the vertical position and screw #2 to adjust the horizontal position.
17 Warranty 1 Year Parts /1 Year Labor This product is warranted to be free from defects in material and workmanship for a period of five years from the date of invoice to the original purchaser . If during the warranty period the product is found to be defective, it will be repaired or replaced at the facilities of Navitar .
18 Navitar , Inc. 200 Commerce Drive Rochester , NY 14623 (716) 359-4000 phone (716) 359-4999 fax Internet http://navitar .com/ e-mail info@navitar .com.
Een belangrijk punt na aankoop van elk apparaat Kodak VIDEOMATE 2030P (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Kodak VIDEOMATE 2030P heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Kodak VIDEOMATE 2030P vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Kodak VIDEOMATE 2030P leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Kodak VIDEOMATE 2030P krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Kodak VIDEOMATE 2030P bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Kodak VIDEOMATE 2030P kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Kodak VIDEOMATE 2030P . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
