Gebruiksaanwijzing /service van het product 10BASE-T van de fabrikant KTI Networks
Ga naar pagina of 17
Installation Guide 10BASE-T/100BASE-TX 8-Port Dual-Speed Hub Model: KF-8D DOC.980329-KF8D-K P/N: 750-0109-001.
Ó 1998 KTI Networks Inc. All rights reserved. No part of this docu- mentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc.
8-Port Dual-Speed Ethernet/Fast Ethernet Hub Installation Guide DOC.980330-KF8D-NK P/N: 750-0109-002.
The information contained in this document is subject to change without prior no- tice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
T able of Contents Chapter 1 Introduction Introduction ............................................................................... 1 Features ................................................................................... 2 Dual-speed Hub T echnology .
1. Introduction KF-8D dual-speed Fast Ethernet/Ethernet hub is designed to allow easy and flexible migration from 10Mbps Ethernet to 100Mbps Fast Ethernet. The hub complies with IEEE 802.3 and IEEE 802.3u repeater specifications and supports 10Mbps and 100Mbps con- nectivity over UTP cabling in the same hub.
Features • Complies with IEEE 802.3 and IEEE 802.3u standard for Ethernet/Class II Fast Ethernet repeater • Provides a configuration switch (10M/100M/AUTO) to set all 8 TP ports as 10BASE-T ports, 100BASE-TX ports or 10/100 auto-sensing ports.
Dual-speed Hub T echnology Dual-speed hub is designed to support connections with different speeds in the same hub. It makes a network planning simpler, espe- cially when an environment is containing 10Mbps Ethernet and 100Mbps Fast Ethernet technologies.
2. Installation Unpacking Check to see that you have everything before you start the installation. • Installation guide • The hub unit • One AC power adapter for the hub • One wall mount kit Checking AC Power Before you begin the installation, check the AC voltage of your area.
The power socket for the AC power adapter is located on the rear of the hub as shown below: Mounting the Hub The hub can be placed on a desktop as a stand-alone unit. It also can be mounted on a wall. The following procedure describes how to mount the hub onto a wallboard or wood (a stud, heavy wooden paneling, etc.
3. Place the hub against the wall so that the mount bracket fits into the slot bracket on the back of the hub. 4. Slide the hub down until it hangs on the mount bracket.
3. Making Network Connections Network Connectors and Rear Switch The hub provides 8 dual-speed TP ports. Each can support one con- nection to either a 10BASE-T Ethernet device or a 100BASE-TX Fast Ethernet device using 2-pair UTP cable. One configuration switch is located on the rear panel.
RJ-45 Connectors Each of Port #1 to Port #7 provides one RJ-45 connector, which are implemented as MDI-X jack. An MDI-X jack is designed with internal crossover function. The function allows a connection to a computer using straight-through UTP cable.
Connecting to Computers The RJ-45 connectors labeled 1X to 8X can be used for connecting to the network adapter installed in a computer . The network adapter can be a 10BASE-T adapter, a 100BASE-TX adapter, or a 10/100 dual-speed NW ay adapter .
Connecting to Hubs The following table lists the types and the maximum number of hub connections depending on the configuration switch setting: Configuration T ypes of hubs Connections 10M mode 10BASE.
Connecting to a Fast Ethernet Hub Since the KF-8D is designed to comply with IEEE 802.3u Class II repeater specifications, it can support one connection to another 100BASE-TX Class II hub. The connection rules are: 1. The other hub which is connected to KF-8D must comply with IEEE 802.
4. Interpreting LED Indicators The following figure shows the locations of the LED indicators: Power LED : indicates the status of the repeater power source. State Indication Interpretation On Normal The power of the hub is on. O f f Problem No power is being supplied to the hub.
Een belangrijk punt na aankoop van elk apparaat KTI Networks 10BASE-T (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen KTI Networks 10BASE-T heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens KTI Networks 10BASE-T vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding KTI Networks 10BASE-T leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over KTI Networks 10BASE-T krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van KTI Networks 10BASE-T bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de KTI Networks 10BASE-T kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met KTI Networks 10BASE-T . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
