Gebruiksaanwijzing /service van het product T545 van de fabrikant Lenovo
Ga naar pagina of 59
DANGER To avoid shock hazard: • Do not remove the covers. • Do not operate this product unless the stand is attached. • Do not connect or disconnect this product during an electrical storm. • The power cord plug must be connected to a properly wired and grounded power outlet.
GEV AAR Ga als volgt te werk om het gevaar van een elektrische schok te voorkomen: • Verwijder in geen enkel geval de kap. • Stel dit produkt alleen in werking als de voet is bevestigd. • Sluit dit apparaat niet aan op, of verbreek de aansluiting van dit apparaat niet van een contactdoos tijdens onweer.
PERIGO Para evitar o perigo de choques eléctricos: • Não retire as coberturas. • Não utilize este produto antes de montar a base. • Não ligue nem desligue este produto durante uma tempestade eléctrica. • O cabo de alimentação deve ser ligado a uma tomada eléctrica devidamente ligada à terra.
ARNING - LIVSF ARA För att undvika risk för elektriska stötar måste du tänka på följande: • Ta inte bort några skyddskåpor. • Använd inte den här produkten innan du har satt fast stativet. • Anslut inte produkten till ett eluttag under åskväder.
• Bu cihaz 7 elektriksel f 7 rt 7 na s 7 ras 7 nda prize takmay 7 n 7 z veya prizden ç 7 karmay 7 n 7 z. • Elektrik kablosunun fi t i, elektrik ve toprak ba 5 lant 7 lar 7 usulüne uygun olarak yap 7 lm 7t bir prize tak 7 lmal 7 d 7 r.
.
.
.
.
위험 전기 충격을 피하려면, • 제품의 덮개를 제거하지 마십시오. • 스탠드가 부착되어 있지 않으면 이 제품을 작동시키지 마십시오. • 뇌우를 동반할 때는 제품을 연결하거나 분리하지 마십시오.
3 These user’s setup instructions cover typical user environments. The on-screen messages may differ depending on the level of your hardware and software. In some cases you may need to vary the setup procedures. For more information, refer to your computer or operating system manuals or consult your system administrator or dealer.
i i First Edition (May / 2001) This publication could contain technical inaccuracies or typographical errors. Changes are made periodically to the information herein; these changes will be made in later editions. IBM may make improvements and/or changes in the product(s) and/or program(s) at any time.
ENGLISH 1 Setup.......................................................................................................................... ..2 Hardware Requirements ......................................................................................2 Handling Instructions .
2 Hardware Requirements This monitor requires a computer with a suitable on-board sub-system or Video Adapter card that can support XGA 1024 x 768, SVGA 800 x 600, or VGA 640 x 480 at 60Hz. Setup Do not support the monitor within the screen area. The Liquid Crystal Display is glass and can be damaged by rough handling or excessive pressure.
ENGLISH 3 i This section gives advice on how you can work comfortably and reduce fatigue. Rest Take regular breaks. Vary your posture, stand up and stretch occasionally as prolonged use of computer workstations can be tiring. Back You should sit back in your chair and use the backrest.
4 1. Turn off your computer and all attached devices. 2. Connect the monitor signal cable to the Video output of your computer and tighten the thumscrews. Ensure that the connectors align. Do not force the connectors as this may bend the pins. 3. Connect the power cord.
ENGLISH 5 Viewing Angle You can tilt the screen backward and forward as shown below(figure A). Rotate You can rotate the screen leftward and rightward as shown below(figure A). Height You can adjust height of the screen(figure B). Before adjusting your monitor for the first time, remove the locking clip on rear of the stand.
6 To use the Plug and Play feature in Windows 95 or Windows 98, files should be loaded from the IBM Monitor Installation diskette . 1. Turn off the computer and all attached devices. 2. Ensure that the monitor is connected correctly. 3. Turn on the monitor and then the system unit.
ENGLISH 7 To use the Plug and Play feature in Windows 2000, files should be loaded from the IBM Monitor Installation diskette . 1. Turn off the computer and all attached devices. 2. Ensure that the monitor is connected correctly. 3. Turn on the monitor and then the system unit.
8 When you first use your monitor you must perform Auto Setup. This procedure sets up your monitor to process the video signals from your computer without image discoloration or smearing. After you perform Auto Setup, the settings are stored and used each time you turn on the monitor.
ENGLISH 9 1. Turn on the monitor first; then the computer. If the message CHECK SIGNAL CABLE is displayed, or if nothing is displayed check: • that the video interface cable is not connected properly. • the correct video adapter card is not installed.
10 1. Turn on the monitor first; then the c om puter. If the message CHECK SIGNAL CABLE is displayed, or if nothing is displayed check: • that the video interface cable is not connected properly. • the correct video adapter card is not installed. 2.
ENGLISH 11 10. Press the ESC key to return to Windows. You have completed the monitor setup for Windows. If you use other operat- ing systems, perform the appropriate AUTO SETUP for those systems, also: see Auto Setup for DOS on page 9.
12 Normally, you can complete the setup procedure using A UTO S ETUP , however, if your screen image is still distorted after you perform A UTO S ETUP or the setup diskette does not run on your system, perform M ANUAL S ETUP . 1. Have your monitor turned on for about 15 minutes, until the monitor warms up.
ENGLISH 13 Adjusting Y our LCD Monitor User controls User control features Icon Direct Access Function 1. Brings up Brightness control OSD 2. Left and Right arrows pressed together bring up auto setup 1. Exits from menus, sub menus 2. Exits from OSD Function Using Menu Controls Moves the cursor to highlight icons or make adjustments.
14 CONTROLS LOCK / UNLOCK This feature allows you to secure the current control settings, while allowing the user to adjust Brightness, Contrast and initiate Auto Setup, so that they cannot be inadvertently changed. Push and hold the enter button[ ] for 10 seconds; the message “ Controls Locked ” appears.
ENGLISH 15 The settings adjustable with the user controls are viewed through the On - Screen Display (OSD). Press the ent er button [ ] to display the main OSD menu. Initial appearance of OSD main menu; On-screen display (OSD) controls i The LCD monitor needs time to become thermally stable the first time you turn it on each day.
16 OSD Icon COLOR Select the Color Mode you find most comfortable and then fine tune the colors using the User Color Mode menu, if necessary. Description Sub-menu(s) Manual SET- UP • Fine • Coarse.
ENGLISH 17 Moves the screen up and down. It is not availible when the digital input Moves the screen left and right . It is not availible when the digital input OSD Icon Sub-menu(S) • YES • NO Con.
18 The display mode the monitor uses is controlled by the co m puter. Therefore, you should refer to your com puter documentation for details on how to change display modes. The image size, position and shape may change when the display mode changes. This is normal and the image can be readjusted using AUTO SETUP and the monitor controls.
ENGLISH 19 To benefit from power management, the monitor must be used in conjunction with a computer that implements the Video Electronics Standards Association (VESA) Display Power Management Signalling (DPMS) Standard.
20 T roubleshooting If you have a problem setting up or using your monitor, you may be able to solve it yourself. Before calling your retailer or IBM, try the suggested actions that are appropriate to your problem. Problem No power to monitor. Possible Cause Suggested Action Reference Brightness and Contrast may be too low.
ENGLISH 21 i For image problems, you may want to run A UTO S ETUP again before consulting to this section. In most cases, A UTO SETUP can fix the problems.
22 Machine Name – T545H Color Monitor Warranty Period – Three (3) Years See the IBM Statement of Limited Warranty included in this publication for IBM ’ s warranty terms and conditions. The IBM Machine Warranty worldwide Web site at http://www-1.
ENGLISH 23 2. Lift the bottom of the cable cover (A) and pull it off. 3. Lay the monitor facedown on a cushion and remove the four screws holding the hinge mechanism on the monitor. Lift off the hinge and base assembly(B). 4. If you are installing an arm or wall-mounting device, follow the directions included with the device.
24 Pin Signal(DVI-I) Pin Signal(DVI-I) 1. T. M. D. S. Data2- 2. T. M. D. S. Data2+ 3. T. M. D. S. Data2/4 Shield 4. T. M. D. S. Data4- 5. T. M. D. S. Data4+ 6. DDC Clock 7. DDC Data 8. Analog Vertical Sync. 9. T. M. D. S. Data1- 10. T. M. D. S. Data1+ 11.
ENGLISH 25 This color monitor (Type-model 9493-Axx) uses a 15.1-inch TFT LCD. Specifications i Power consumption figures are for the monitor and the power supply combined. Dimensions Weight 7.1 kg (15.62 lbs) 0 ° 30 ° Range : 125mm Range : -150 ˚ / +150 ˚ 15.
26 Addressabillty Refresh Rate / Range ( + / - 3%) Horizontal Frequency / Range ( + / - 3%) 640 x 350 67.9 ~ 72.1 Hz 30.56 ~ 31.45 kHz 720 x 400 67.9 ~ 72.1 Hz 30.56 ~ 31.45 kHz 640 x 480 58.2 ~ 61.8 Hz 30.56 ~ 31.45 kHz 640 x 480 64.0 ~ 68.0 Hz 34.95 ~ 36.
ENGLISH 27 Part 1 - General T erms This Statement of Limited Warranty includes Part 1 - General Terms and Part 2 - Country-unique Terms. The terms of Part 2 replace or modify those of Part 1.
28 3. where applicable, before service is provided: a. follow the problem determination, problem analysis, and service request procedures that IBM or your reseller provides; b.
ENGLISH 29 CAMBODIA, LAOS, AND VIETNAM Governing Law: The following replaces “laws of the country in which you acquired the Machine” in the first sentence: laws of the State of New York.
30 If you purchased an IBM Personal Computer Machine in Albania, Armenia, Belarus, Bosnia and Herzegovina, Bulgaria, Croatia, Czech Republic, Georgia, Hungary, Kazakhstan, Kirghizia, Federal Republic .
ENGLISH 31 2. the amount of any other actual direct damages, up to 125 percent of the charges (if recurring, the 12 months’ charges apply) for the Machine that is the subject of the claim or which otherwise gives rise to the claim. Applicability of suppliers and resellers (unchanged).
32 You have just purchased a TCO’95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products.
33 The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level, in one or more stages. The length of time to reactivate the computer shall be reasonable for the user.
34 Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant bio-accumulative TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million) of cadmium.
35 You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
36 Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric and magnetic fields, energy consumption and electrical and fire safety.
37 Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances.
38 Service Information The following parts are for use by IBM service, or IBM authorised dealers, to support the customer warranty. Parts are for service use only.
39 Compliances Federal Communications Commission (FCC) Statement IBM T545H color monitor This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
40 For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a grounding-type attachment plug. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed. IBM power cords for a specific country or region are usually available only in that country or region.
41 Industry Canada Class B emission compliance statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil num é rique de la classe B respecte toutes les exigences du R é glement sur le mat é riel brouilleur du Canada.
42 Congratulations! You have just purchased a TCO99 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
43 products with regards to their eventual recycling and disposal. By proper selection of these materials and substances, the impact on the environment can be minimized.
44 European Union (EU) Statement This product is in conformity with the protection requirements of the EU Council Directive 89/366/ECC on the approximation of the laws of the Member States relating to electromagnetic compatibility.
45 Dieses Gerat ist berechtigt in Ubereinstimmungmit dem Deutschen EMVG das EG-Konformitatszeichen - CE - zu fuhren. Verantwortlich fur die Konformitatserklarung nach Paragraph 5 des EMVG ist die: IBM Deutschland Informationssysteme GmbH, 70548 Stuttgart.
46 IBM non accetta responsabilit à alcuna per la mancata conformit à alle normative di protezione dovuta a modifiche non consi gliate al prodotto, compresa l ’ installazione di schede e componenti di marca diversa da IBM.
47 VCCI Class B Notice (Japan Only) This equipment complies with the limits for a Class B digital device (devices used in or adjacent to a residential environment) and conforms to the standards for in.
Een belangrijk punt na aankoop van elk apparaat Lenovo T545 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lenovo T545 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lenovo T545 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lenovo T545 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lenovo T545 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lenovo T545 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lenovo T545 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lenovo T545 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
