Gebruiksaanwijzing /service van het product LMV1825SB van de fabrikant LG Electronics
Ga naar pagina of 46
MICROWAVE OVEN SERVICE MANUAL MODEL: LMV1825SB BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. LMV1825SW LMV1825SBQ CAUTION website http://www.
CAUTION SAFETY PRECAUTIONS PRECAUTIONS T O BE OBSER VED BEFORE AND DURING SER VICING T O A VOID POSSIBLE EXPOSURE T O EXCESSIVE MICROW A VE ENERGY a. Do not operate or allow the oven to be operated with the door open.
FOREWORD Read this Manual carefully. Failure to adhere to or observe the information in this Manual may result in exposing yourself to the Microwave Energy normally contained within the oven cavity. T ABLE OF CONTENTS (Page) SAFETY PRECAUTIONS .......
1-1 Rated Power Consumption ..................................................1,500W maximum (Microwave oven+Cook top lamps+Ventilation fan) Microwave Output................................................................. 1000W (IEC 60705) Adjustable 100W through 1000W, 10 steps Frequency .
2-1 CAUTIONS • DO NOT operate on a 2-wire extension cord during repair and use. • NEVER TOUCH any oven components or wiring during operation. • BEFORE TOUCHING any parts of the oven, always remove the power plug from the outlet. • For about 30 seconds after the oven stops, an electric charge remains in the high voltage capacitor.
3-1 INST ALLA TION PRECAUTIONS ON INST ALLA TION A. Plug the power supply cord into a 120V AC, 60Hz, single-phase power source with a capacity of 15A or 20A. B. Avoid placing the unit in a location where there is direct heat or splashing water. C. Install the unit on the mounting plate firmly.
CONTROL P ANEL 4-1 OPERA TING INSTRUCTIONS 25 24 4 7 9 15 22 21 8 10 17 20 23 2 5 3 6 1 12 13 11 16 14 18 19.
CONTROL P ANEL INSTRUCTIONS 4-2 1. DISPLAY: The Display includes a clock and indicators to tell you time of day, cooking time settings and cooking functions selected. 2. MORE: Touch this pad to add ten seconds of cooking time each time you press it. 3.
5-1 SCHEMA TIC DIAGRAM OVERALL CIRCUIT DIAGRAM.
5-2 MA TRIX CIRCUIT FOR TOUCH KEY BOARD REHEAT N.C N.C CUSTOM POWER PIZZA CLEAR STOP TIMER MORE TURNTABLE ON/OFF COOK POPCORN POTATO VEGETABLE VEGETABLE N.C START WARM HOLD LEVEL CLOCK SET CUSTOM LIGHT HI/LO/OFF LESS LIGHT HI/LO/OFF VENT N.C Ez-On TIMER KITCHEN N.
6-1 GENERAL PRECAUTIONS IN USE A. Never operate the unit when it is empty. Operating the oven with no load may shorten the life of the magnetron. Whenever cooking dry foods (dried fish, bread, etc.) or a small amount of food, be sure to put a glass of water into the cooking compartment.
PRELIMINAR Y A. SINCE NEARLY 2,100 VOLTS EXISTS IN SOME CIRCUITS OF THIS UNIT REPAIRS SHOULD BE CARRIED OUT WITH GREAT CARE. The filament leads of magnetron carry High Voltage with respect to ground. Extreme caution must be exercised. Never plug the unit into a power source to determine which component is defective in high voltage section.
7-2 CAUTIONS • Be sure to check microwave leakage prior to servicing the oven if the oven is operative prior to servicing. • The service personnel should inform the manufacture importer, or assemb.
MEASUREMENT WITH THE OUTER CASE REMOVED (1) When you replace the magnetron, measure for microwave energy leakage before the outer case is installed and after all necessary components are replaced or adjusted. Special care should be taken in measuring the following parts.
IMPORT ANT NOTES: UNIT MUST BE DISCONNECTED FROM ELEC- TRICAL OUTLET WHEN MAKING REPAIRS, RE- PLACEMENTS, ADJUSTMENTS AND CONTIN- UITY CHECKS. WAIT AT LEAST ONE MINUTE, UNTIL THE HIGH VOLTAGE CAPACITOR IN THE HIGH VOLTAGE POWER SUPPLY HAS FULLY DISCHARGED.
7-5 HOW TO REMOVE THE F .P .C. CONNECTOR Follow the steps below as illustrated in Figures 4 and 5 to remove the F.P.C. connector. (1) Hold the edges of the plastic fastener with thumb and forefinger. (Figure 4) (2) Lift up the lever of the plastic fastener from the terminal socket by lightly pressing the lever end with forefinger.
B. REMOVING THE OUT CASE(Figure 8) (1) Remove the vent grille by removing two screws securing it to the out case. (2) Remove two screws securing it to the air duct. (3) Remove the mounting plate by turning the screws (1 or 2 screws) securing it to the out case.
WIRE COLOR SYMBOL COLOR WH BK BR RD BL PK GY N.P. WHITE BLACK BROWN RED BLUE PINK GREY Not Provided Latch Board Secondary Interlock Switch Interlock Monitor Switch Primary Interlock Switch Latch Board WH (from H.
V ent Grille Controller (3 screws) Door Mounting Plate (1 or 2 screws) Out Case Mount,All D. REMOVING MAGNETRON (Figures 11 Through 13) (1) Remove the vent grille by loosening two screws. (Figure 11) (2) Remove the outcase. See page 7-6. (3) Remove three tap tite screws securing the magnetron to the wave guide.
E. REMOVING STIRRER F AN (Figures 14 and 15) (1) Remove one rivet ASS'Y securing it to the oven upper plate by using knife blade. (2) Rotate slightly and pull out the stirrer fan cover. (3) Remove the stirrer fan. F . REMOVING DOOR (Figure 16) (1) Remove the vent grille by two screws securing it to the outcase loosening.
H. ASSEMBLING DOOR (1) When mounting the door assembly to the oven assembly, be sure to adjust the door assembly parallel to the chassis. Also adjust so the door has no play between the inner door surface and oven frame assembly. If the door assembly is not mounted properly, microwaves may leak from the clearance between the door and the oven.
K. REMOVING THE TURNT ABLE MOTOR (1) Remove the turntable. (2) Remove the turntable shaft VERY CAREFULLY with a slotted screwdriver. (Figure 20) (3) Remove the base plate by removing 7 screws securing it to the oven cavity. (Figure 21) (4) Disconnect the leadwire from the turntable motor terminals.
7-12 ADJUSTMENT PROCEDURES To avoid possible exposure to microwave energy leakage, adjust the door latches and interlock switches, using the following procedure. The Interlock Monitor and Primary Interlock Switch act as the final safety switch protecting the user from microwave energy.
7-13 TEST THE LATCH AND SWITCH SEQUENCE (5) Open the oven door slowly. Watch the door latch, the Secondary Switch. Release Rod and Lever on the switches to make sure they are zero to the body of the s.
7-14 A. PRIMARY INTERLOCK SWITCH TEST When the door is opened slowly, an audible click should be heard at the same time or successively at intervals and the latches should activate the switches with an audible click .
7-15 - CAUTIONS - - DISCONNECT THE POWER SUPPLY CORD FROM THE WALL OUTLET WHENEVER REMOVINGING THE CABINET FROM THE UNIT. PROCEED WITH THE TESTS ONLY AFTER DISCHARGING THE HIGH VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE HIGH VOLTAGE TRANSFORMER.
7-16 COMPONENTS TEST PROCEDURES RESULTS HIGH-VOLTAGE CAPACITOR HIGH-VOLTAGE DIODE Measure the resistance: (1) Terminal to terminal Ohm- meter Figure 25-a (2) Terminal to case Ohm- meter Figure 25-b Me.
REHEAT REHEAT N.C N.C N.C N.C CUSTOM CUSTOM POWER POWER PIZZA PIZZA CLEAR CLEAR STOP STOP TIMER TIMER MORE MORE TURNTABLE TURNTABLE ON/OFF ON/OFF COOK COOK POPCORN POPCORN POTATO POTATO VEGETABLE N.
7-18 COMPONENTS TEST PROCEDURES RESULTS RELAY2 Check for continuity of relay 2 with an ohm-meter. (Remove wire leads from relay 2 and operate the unit.) NOTES: • A MICROWAVE ENERGY TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR ANY REASON.
7-19 (2) CHECKOUT PROCEDURES FOR RELAY. - PROBLEM (A) - FAN motor and oven lamp turn on without touching START key when the door is closed. Remove the mate connector of I/O CON from the circuit board.
7-20 NOTE: A MICROWAVE ENERGY LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR ANY REASON. (3) CHECKOUT PROCEDURES FOR CIRCUIT BOARD The following symptoms indicate a defective circuit board. 1) The start function fails to operate but the high voltage Systems, the interlock switches, the door sensing and the relay check good.
7-21 PROBLEM - A: PLEASE SET TIME OF DAY does not appear in display window when power supply cord is plugged into wall outlet. PROBLEM - B: Display does not show correct numbers and/or correct indications when programmed. Check: 1. POWER SUPPLY 2. FUSE (See CHECKOUT PROCEDURES FOR FUSE BLOWING: on page 7-18) 3.
7-22 PROBLEM - C: Display does not start countdown when ST ART key is touched. PROBLEM - D: Unit operation seems to be normal but little or no heating is produced in oven load.
7-23 PROBLEM - E: Unit does not heat up even if display counts down when START key is touched for HIGH POWER cooking. Check: 1. PRIMARY AND SECONDARY INTERLOCK SWITCHES 2. THERMOSTAT 1 2 Runs Contact OK Resistance incorrect Check the continuity of H.V.
7-24 PROBLEM - F: No buzzing when touching the key, between stages or at end of cooking 1 Normal circuit board Check normal operation circuit board Replace circuit board Runs.
7-25 PROBLEM - G: Ventilation fan does not operate when FAN HIGH/LOW key is touched. 1 Check: 1. POWER SUPPLY 2. FUSE Contact OK NO contact Replace magnetron thermal fuse and oven thermostat Poor cont.
8-1 EXPLODED VIEW DOOR 13581A 13552A WTP004 13536A 13213A 14760A 13720D 13650A WTT028 14890A 14970A 14026A.
8-2 CONTROL P ANEL 24781M 24810P 268711 WTP018 * 07 23506A.
8-3 OVEN CA VITY 33530A 34960A 33550P WTT021 WTT027 WTT029 WTT028 WTT029 WTT027 33112U WTT022 34810Q 34930R 330342 535501 35230A WTT022 63302A 56804A 368771 63303A 36912C WTT022 330341 35026G.
8-4 LA TCH BOARD 466001 43501A 43500A 466003 466001 44510A WSZ084.
8-5 INTERIOR (I) 33390G 34370T 35889A 33052A 55892A 53550F 340511 54930F WTT021 56930G WSZ002 WTP013 53300B WSZ002 WTP002 56170D WSZ002 56851D 50CZZH WTT021 54810C 55238A WSZ002 56324A 36549S 568772.
8-6 INTERIOR (II) WTT028 56501A 56930V 55231C *01 568771 WTT028 56549F 55262A WTT034 36549V 56912B WTP004 WSZ002 WTT029 535502 56411A 55900A 33700A 56804A 56901A *02 *04 50FZZA WTP013 56820A.
8-7 INST ALLA TION WSZ133 44360A WSZ098 WWZ068 WWZ068 WSZ204 56411A 65862D 63300M 63861A WSZ203 WSZ136 65862B.
8-14 SCHEMA TIC DIAGRAM OF P .C.B REHEAT REHEAT N.C N.C N.C N.C CUSTOM CUSTOM POWER POWER PIZZA PIZZA CLEAR CLEAR STOP STOP TIMER TIMER MORE MORE TURNTABLE TURNTABLE ON/OFF ON/OFF COOK COOK POPCORN POPCORN POTATO POTATO VEGETABLE N.
8-15 PRINTED CIRCUIT BOARD.
P/NO : 3828W5S3224 May, 2003 Printed in Korea.
Een belangrijk punt na aankoop van elk apparaat LG Electronics LMV1825SB (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen LG Electronics LMV1825SB heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens LG Electronics LMV1825SB vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding LG Electronics LMV1825SB leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over LG Electronics LMV1825SB krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van LG Electronics LMV1825SB bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de LG Electronics LMV1825SB kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met LG Electronics LMV1825SB . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
