Gebruiksaanwijzing /service van het product WD-12124RD van de fabrikant LG Electronics
Ga naar pagina of 43
W ASHING MACHINE SER VICE MANUAL READ THIS MANUAL CAREFULL Y TO DIAGNOSE TROUBLES CORRECTL Y BEFORE OFFERING SERVICE. MODEL : WD-14124(6)RD WD-12124(6)RD WD-10124(6)RD CAUTION.
CONTENTS 1. SPECIFICA TION ............................................................................................................................3 2. FEA TURES & TECHNICAL EXPLANA TION ........................................................
3 1. SPECIFICA TION ITEM WD-14124(6)RD/WD-12124(6)RD/WD-10124(6)RD PO WER SUPPL Y 220V -240V~, 50HZ PRODUCT WEIGHT 71kg W ASHING 140W SPIN 300W F AN MOTOR 25W DRAIN MOTOR 40W W ASH HEA TER 2000W DRY H.
Automatic process from washing to drying. Automatic process from washing to drying can be selected easily . W ashing capacity : 7 kg (Cotton) Drying capacity : 3.
2-2.DETERMINE W ASHING TIME BY FUZZY LOGIC T o get the best washing performance optimal time is determined by sensing of water temperature, selected washing temperature and laundry amount. 2-3.W A TER LEVEL CONTROL This model adopts a pressure sensor which can sense the water level in the tub.
3. P AR TS IDENTIFICA TION 6 ACCESSORIES Power plug Control panel Door Lower cover Adjustable feet (For detergent and fabric softener) Drawer Drum Drain hose Lower cover cap Drain pump filter Drain pl.
Before servicing ask troubles of customers Check the adjustment(power supply is 220-240V~, remove the transit bolts....) Check the troubles referring to the trouble shooting. Decide service steps referring to disassembly instructions. And then, service and repair .
HOW TO CONNECT INLET HOSE Check that the rubber packing is inside of the valve connector . Connect the inlet hose firmly to prevent leak. CONNECT DRAIN HOSE CONNECT POWER PLUG 8 Make sure that the hose is not twisted. The drain hose should be placed under 100cm from the floor .
TEST OPERA TION 9 Power Star t / Pause Power Connect the power plug to the outlet. In case of Coloreds program. Connect the inlet hose. Preparation for Press the POWER button.
10 5. OPERA TION Start/Pause button • Use the button to start or pause wash cycle. •The power turns off automatically in 4 minutes after the pause button is pressed. • Press the button to change the program. Wash program selector • 7 programs can be selected depending on the type of the laundry.
11 Dry selector • Dry programs can be selected by pressing the [Dry] button. • By pressing the button, [Auto Big Time Add Small ] can be selected. Water temperature selector • Press the button to select water temperature. • The water temperature is selected [60°C 95°C Cold 30°C 40°C] during cotton program.
12 6. WIRING DIAGRAM / PROGRAM CHAR T MAIN PWB NA YL YL BL BL RD WH RD RD FUSE DOOR LOCK S/W DRAIN MOTOR UV W BK BK BL BN GN / YL GN / YL VL / WH WH / RD BL / RD YL / RD BN / YL WH / BK GY / WH YL / B.
13 7. TROUBLE SHOOTING 7-1.BEFORE SVC CHECKING Be careful of electric shock or disconnecting the parts while trouble shooting. V oltage of each terminal in 220-240V~ and DC while applying an electric current. 7-2.QC TEST MODE. Pressing Rinse, and Spin button simultaneously .
14 7-5.ERROR DISPLA Y. If you press the Start/Pause button in error condition, any error except ‘’ will disappear and the machine will change into pause status. In case of if the error is not resolved within 20 sec., and in case of other errors, if the error is not resolved within 4 min.
ERROR SYMPTOM CAUSE 8 9 10 • MAIN PWB ASSEMBL Y is out of order Replace the MAIN PWB ASSEMBL Y • Winding in the ST A TOR ASSEMBL Y is short-circuited.
16 8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERA TION 8. ERROR DIAGNOSIS AND CHECK LIST SYMPTOM GUIDE FOR SERVICE CALL NO POWER W ater inlet trouble Is the power plug connected firmly to 220-240V~ outle.
17 SYMPTOM • Door does not open • Error displayed on the program • DRAIN TROUBLE GUIDE FOR SERVICE CALL NO YES NO YES Started with door opened? NO YES Is the debris filter clogged with foreign material such as pin, coin and etc.
18 SYMPTOM GUIDE FOR SERVICE CALL Suds overflow from the appliance. (In this condition, wash and spin do not operate normally) No effect of softener Is low-sudsing detergent for the drum washing machine used? Is the proper amount of detergent used as recommended? Recommend to reduce the using amount of detergent.
19 8-2.FAUL T DIAGNOSIS AND TROUBLE SHOOTING 1. Be careful of electric shock or disconnecting the parts while trouble shooting. 2. First of all, check the connection of each part terminal with wiring diagram. 3. If you replace the MAIN PWB ASSEMBL Y , Put in the connectors correctly .
20 MAX Is water supply shut-off? Is the tap opened? When you press both Rinse button and Spin button simultaneously , is the water level frequency below 240? Is the inlet valve filter clogged with impurity? Is resistance between each terminal of INLET V AL VE ASSEMBL Y is 2~8 k ? Check the voltage of the inlet valve connector 220-240V~.
21 ABNORMAL SOUND SOFTENER DOES NOT FLOW IN Fix the bolt tightly . Replace the ST A TOR ASSEMBL Y or ROTOR ASSEMBL Y . Refer to NO W A TER SUPPL Y Check the wiring on the dispenser .
22 W ash Rinse Replace the S.PRESSURE SWITCH ASSEMBL Y Replace the MAIN PWB ASSEMBL Y Repair the DRAIN HOSE ASSEMBL Y . Remove foreign material. Reconnect or repair the connector Repair the DRAIN PUMP ASSEMBL Y .
23 Push the THERMISTOR tightly to the rubber . When checking THERMISTOR on the tub is the THERMISTOR loosened above 2mm from the rubber? HEA TING CONTINUOUSL Y ABOVE THE SETTING W A TER TEMPERA TURE.
24 Rinse Spin W ash Rinse Door Lock SPIN TROUBLE DOOR DOES NOT OPEN Check the S.PRESSURE SWITCH ASSEMBL Y or HOSE (Pressure). If the problem is on the S.PRESSURE SWITCH ASSEMBL Y or the HOSE, replace the S.PRESSURE SWITCH ASSEMBL Y or the HOSE. Normal Correct the connector .
Disassemble the cabinet cover and condensing bellows. Is there any foreign object in condensing bellows. Clean the bellows [dHE] ERROR DISPLAY CHECK FOR DRY HEATER TROUBLE CHECK FOR DRY FAN MOTOR TROUBLE NO YES Replace the thermistor. (6322FR2046B) YES NO Disassemble the dry fan assy and dry duct upper, and clean foreign object in duct and fan.
26.
27.
28.
9. DISASSEMBL Y INSTRUCTIONS ƒR Disassemble and repair the parts after pulling out power cord from the outlet. ¤ Unscrew the screws on the top plate. ¤Ł The plate assembly(T op) is pulled back and then upward to arrow direction. ¤Ø The cover(Inner) is disassembled.
30 ¤ The back cover is removed. ¤Ł T wo screws are unscrewed. ¤Ø Disconnect connector from the wiring. ¤Œ Pull the PWB assembly (Main) to arrow direction. ¤ The plate assembly(T op)and the cover(lnner)are disassembled. ¤Ł Pull the drawer to arrow direction.
31 ¤ Disconnect the wiring connector . ¤Ł Remove the valve by two screws of the valve holder . ƒT When reconnecting the connector 2 1 3 4 INLET VALVE V AL VE ¥L (DRY) YL/BK - BK V AL VE ¥M (PRE-.
32 ¤ Open the door completely . ¤Ł Remove the two screws from the hinge. ¡ When removing the Door Assembly , it is necessary to hold the Bracket that is inner of the Cabinet Cover . ¤ Rotate the Cap(Remaining Hose) to arrow direction. ¤Ł Pull it out from hose.
33 ¤ The cabinet gasket clamp is released. ¤Ł T wo screws are unscrewed from the cabinet cover . ¤ One screw is unscrewed from the lower cover . ¤Ł The lower cover is disassembled by pulling out. ¤Ø Three screws are unscrewed from the cabinet.
34 ¤ Remove tub gasket clamp by loosening the screw . ¤ Remove dry gasket clamp by loosening the screw . ¤ When reassembling the gasket, put the drain hole of the gasket downward, then assemble.
35 ¤ Remove the back cover . ¤Ł After loosening the bolt, Rotor , pull out the rotor . ¤ Remove the 6 bolt from the stator . ¤Ł Disconnect the 2 connectors. ¤ Remove the bolts at the T ub. ¤Ł The Hinge(Damper) at the base is pulled of f pressing on the snaps at the sharp end.
¤ Remove pump outlet hose. ¤Ł Remove tub pump bellows. ¤Ø Remove cap(Remaining Hose). ¤Œ Disconnect the wiring. ¤º Three screws are unscrewed from the cabinet. ¤ Remove the pump to arrow direction. ¤ Loosen the nut. ¤Ł Remove washing heater by pulling out.
¤ The cabinet cover clamp is removed and the gasket is released. ¤Ł T wo screws are unscrewed. ¤Ø The door lock S/W is disconnected form the wiring connector and the strap. ¤ Remove washing heater . ¤Ł Remove the foreign object(wire,coin,etc) by inserting long bar in the hole.
¤ Remove 5 screws and dry fan assembly . ¤Ł Remove 6 screws and dry duct upper . ¤ Remove 1 screw and dry heater . ¤Ł Remove thermostat. ¤ Remove 2 screws from cabinet.
10-1.THE P AR T LIST OF CABINET ASSEMBL Y 10. EXPLODED VIEW AND P AR T LIST A110 A101 A100 A410 A201 A220 A210 A303 A310 A133 A440 A130 A131 A141 A103 A104 A102 A150 A120 A200 A300 A430 A485 A450 :Non.
10-2 THE EXPLODED VIEW OF CONTROL P ANEL & DISPENSER ASSEMBL Y 40 F160 F430 F461 F310 K343 F460 F300 F170 F120 F450 F220 F130 :Non-service part :Service part F210 F110.
10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBL Y K350 K143 K310 K105 K410 K610 K611 F140 K320 K540 K520 K531 K340 K344 K341 K343 K530 K100 K510 K511 K513 K131 K130 K141 K140 K110 K142 K411 K420 K123.
10-4 THE EXPLODED VIEW OF DR YER M100 M110 M210 M101 M220 M230 M120 M121 M310 M312 M311 :Non-service part :Service part 42.
MA Y . 2002 PRINTED IN KOREA P/No.:3828ER3013K.
Een belangrijk punt na aankoop van elk apparaat LG Electronics WD-12124RD (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen LG Electronics WD-12124RD heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens LG Electronics WD-12124RD vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding LG Electronics WD-12124RD leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over LG Electronics WD-12124RD krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van LG Electronics WD-12124RD bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de LG Electronics WD-12124RD kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met LG Electronics WD-12124RD . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.