Gebruiksaanwijzing /service van het product 2010 Navigator van de fabrikant Lincoln Electric
Ga naar pagina of 385
Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 17 Message center 19 Entertainment Systems 30 AM/FM stereo with CDX6/MP3 30 Auxiliary input jack (Line in) 36 USB port 38 Rear.
Locks and Security 132 Keys 132 Locks 133 Anti-theft system 144 Seating and Safety Restraints 154 Seating 154 Safety restraints 173 Airbags 186 Child restraints 196 Tires, Wheels and Loading 215 T ire.
Customer Assistance 321 Reporting safety defects (U.S. only) 327 Reporting safety defects (Canada only) 327 Cleaning 328 Maintenance and Specifications 335 Engine compartment 337 Engine oil 340 Batter.
CONGRATULATIONS Congratulations on acquiring your new Lincoln. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.
W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment.
Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage.
DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems.
T o access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtainin.
W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emper.
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter . If the light is blinking, engine misfire is occurring which could damage your catalytic converter .
Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately by your authorized dealer . Normal braking is still functional unless the brake warning light also is illuminated.
Engine coolant temperature (R TT): Displays when the engine coolant temperature is high. Stop the vehicle as soon as safely possible, switch off the engine and let it cool. Refer to Engine coolant in the Maintenance and Specifications chapter . W ARNING: Never remove the coolant reservoir cap while the engine is running or hot.
AdvanceT rac 威 (if equipped): Displays when the AdvanceT rac 威 with RSC 威 system is active. If the light remains on, have the system serviced immediately by your authorized dealer . Speed control: Illuminates when the speed control is activated.
High beams: Illuminates when the high beam headlamps are turned on. Key-in-ignition warning chime: Sounds when the key is left in the ignition in the off or accessory position and the driver’ s door is opened.
Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating.
Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the on position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. Refer to Filling the tank in the Maintenance and Specifications chapter for more information.
TRIP A/B Registers the distance of individual journeys. Press and release INFO button until the A or B trip appears in the display (this represents the trip mode). Press and hold the RESET button to reset. Refer to UNITS later in this section to switch the display from Metric to English.
• Differences in the automatic shut-off points on the fuel pumps at service stations • V ariations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) T o determine your average highway fuel economy , do the following: 1.
Note: Some systems show a message only if a condition is present. 1. OIL LIFE 2. CHARGING SYSTEM 3. W ASHER FLUID LEVEL 4. DOOR ST A TUS 5. LIFTGA TE/GLASS 6. BRAKE SYSTEM 7. TIRE PRESSURE 8. AIR SUSPENSION SYSTEM 9. FUEL LEVEL 10. MYKEY MILES (if programmed) 11.
UNITS Displays the current units English or Metric. Press the RESET button to change from English to Metric. AUTOLAMP This feature keeps your headlights on for up to three minutes after the ignition is switched off. Press the RESET button to select the new Autolamp delay values of 0, 10, 20, 30, 60, 90, 120 or 180 seconds.
Press the RESET button to select the running boards setting as follows: • AUTO: the running boards will automatically deploy when a door is opened and automatically retract when the door is closed, • OUT : the running boards will remain deployed regardless of the doors being open/closed.
Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error .
CREA TE MYKEY / CLEAR MYKEY / MYKEY SETUP For more information refer to MyKey™ in the Locks and Security chapter . ENGLISH / FRENCH / SP ANISH RESET FOR NEW Allows you to choose which language the message center will display in. Selectable languages are English, Spanish, or French.
CHECK CHARGING SYSTEM — Displayed when the electrical system is not maintaining proper voltage when the engine is running. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible.
CHECK AIR SUSPENSION (if equipped) — Displayed when the air suspension system is not operating properly . If this message is displayed while driving, pull off the road as soon as safely possible. For more information, refer to Air suspension system in the Driving chapter .
KEY COULD NOT PROGRAM — Displayed when an attempt is made to program a spare key using two existing MyKeys. Refer to MyKey™ in the Locks and Security chapter for more information. VEHICLE SPEED 80 MPH MAX — Displayed when a MyKey™ is in use and the Admin has enabled the MyKey speed limit and the vehicle speed is 80 mph (130 km/h).
AUDIO SYSTEMS Note: If your volume is muted and MYKEY VOLUME LIMITED is displayed, refer to MyKey™ in the Locks and Security chapter for more information. AM/FM In-dash six CD/MP3 satellite compatible sound system W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury .
THX: Y our vehicle is equipped with the THX 威 II certified premium audio system. This system creates optimal acoustic quality for all seating positions and road conditions. The system offers an advanced speaker system, amplifier , subwoofer and equalization.
4. MENU: Press MENU repeatedly to scroll through the following modes: SA TELLITE RADIO MENU (if equipped): Press MENU when satellite radio mode is active to access. Press OK to enter into the satellite radio menu. Press / to cycle through the following options: • CA TEGOR Y : Press OK to enter category mode.
• ENABLE ALER TS / DISABLE ALER TS: Press OK to enable/disable the satellite alert status which alerts you when your selected songs are playing on a satellite radio channel. (The system default is disabled.) SONG ALERTS ENABLED/DISABLED will appear in the display .
T reble: Press / to adjust the treble setting. Press OK to close and return to the main menu. Balance: Press / to adjust the audio between the right and left speakers. Press OK to close and return to the main menu. Fade: Press / to adjust the audio between the front and rear speakers.
In TEXT MODE, press TEXT and then SEEK to view the additional display text when “>” is active in the display . Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability . 8. FWD (Fast Forward): Press FWD to manually advance in a CD/MP3 track.
12. SHUFFLE: Press to play all tracks on the current disc in random order . 13. AM/FM: Press to select AM/FM1/FM2 frequency band. 14. CD: Press to enter CD mode. If a CD is already loaded into the system, CD play will begin where it ended last. If no CD is loaded, NO DISC will appear in the display .
Y our vehicle is equipped with an Auxiliary Input Jack (AIJ) located inside the center console. The Auxiliary Input Jack provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity .
7. Adjust the sound on your portable music player until it reaches the level of the FM station or CD by switching back and forth between the AUX and FM or CD controls. T roubleshooting: 1. Do not connect the audio input jack to a line level output. Line level outputs are intended for connection to a home stereo and are not compatible with the AIJ.
Y our vehicle is equipped with a USB port inside your center console. This feature allows you to plug in media playing devices, memory sticks, and also to charge devices if they support this feature. For further information on this feature, refer to Accessing and using your USB port in the SYNC 威 supplement or Navigation system supplement.
Note: After pressing the media button to select SYNC mode, press + or – to scroll through the different SYNC 威 options: (SYNC USB, SYNC BTST and SYNC LINE). For more information on SYNC 威 operation, see your SYNC 威 supplement. 2. VOLUME: Press to increase or to decrease the volume level in the headphones.
When the rear seat controls are activated, rear seat passengers can use the controls to change the playing media for all passengers (Single Play mode) or just for themselves (dual play mode).
The front speakers remain playing for the front passengers. Press the speaker button, or the 2/4 preset buttons simultaneously on the radio again to deactivate the headphones and dual play mode.
• W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only .
Satellite radio information Satellite radio channels: SIRIUS broadcasts a variety of music, news, sports, weather , traffic and entertainment satellite radio channels. For more information and a complete list of SIRIUS satellite radio channels, visit www .
Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes.
Radio Display Condition Action Required NO TEXT Artist information not available. Artist information not available at this time on this channel. The system is working properly . NO TEXT Song title information not available. Song title information not available at this time on this channel.
FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road.
3. Press the power button on the DVD player , then press Play to begin to play the disc. If a DVD is already loaded into the system, press PLA Y on the DVD player . Note: If sound can be heard, but no video is present, press VIDEO to select the video source (DVD or aux-inputs).
3. The disc will begin to play and the ‘CD Audio Disc’ screen will display . From this screen, you can also select from COMPRESSION, SHUFFLE and SCAN features. Note (navigation-based radio systems only): W h e nad i s ci s inserted, the FES switches to dual-play mode–rear speakers turn off, and headphones turn on.
2. Press the power button to turn the DVD system on. The indicator light next to the power button will illuminate. 3. Connect an auxiliary audio/video source by connecting RCA cords (not included) to the RCA jacks on the left hand side of the system.
Repeating each of these actions will switch back to single play mode, all speakers playing and headphones off. A green light will illuminate next to either the A or B Headphone Control Button to indicate which channel is active (able to be controlled).
Using the infrared (IR) wireless headphones: 1. Press the power control on the earpiece to turn the headphones ON. 2. Select Channel A or B for each set of wireless headphones by using the A/B control on the ear piece. 3. Adjust the headphone volume using the rotary dial on the earpiece.
DVD player controls 1. Headphone control A/B: While in Dual Play mode, press to select either the A or B headphone source. Then press MEDIA to select the desired playing media for that headset. When a headphone channel has been selected (A or B), selections will affect the source on that channel only .
4. (Fast forward): Press and release for the next chapter or track. Press and hold to forward search a DVD, Video CD, or FES CD in DVD/CD mode. 5. / (Play/Pause): Press (Play) to select DVD mode (and to turn the DVD system on if it is off). If a disc is present, it will resume or begin to play .
11. / (Headphones/Speakers): Press once for Dual Play (Headphone mode- the rear speakers are muted) and press again for Single Play (same media playing through all speakers). Y ou can also press the 2 and 4 memory preset buttons on the audio system at the same time to perform the same function.
Remote control Unless otherwise stated, all operations can be carried out with the remote control. Always point the remote control directly at the player . Ensure that there are no obstructions between the remote and player . 1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF .
7. VOL (V olume): When in Single Play , press to increase ( )o r decrease ( ) the volume over all speakers. When in Dual Play , press to increase ( ) or decrease ( ) the volume for the wired headphones. (W ireless headphone volume is controlled with the rotary dial on the right ear piece.
21. LANGUAGE (DVD dependent): Press to select the desired language. 22. ENTER: Press to select the highlighted menu option. 23. ILLUMINA TION : Press to illuminate the remote control and backlight all of the buttons. Battery replacement Batteries are supplied with the remote control unit.
Headphones Wireless headphones W ARNING: The driver should never use the headphones while driving the vehicle. Using headphones may prevent the driver from hearing audible warnings such as horns or emergency sirens, which could result in a crash causing serious injury .
T o install the batteries, remove the screw at the bottom of the cover . Then, lightly press down on top and slide the cover off. When replacing the batteries, use two new batteries (alkaline recommended) and install them with the correct orientation as indicated in the battery housing.
T o operate the headphones: • Press POWER on the ear piece to turn on the headphones. A red indicator light will illuminate indicating the headphones are ON. Press POWER again to turn the headphones off. • Adjust the headphones to comfortably fit your head using the headband adjustment.
Wired headphones W ARNING: Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may become entangled in the cords and seriously injure themselves.
Single Play: Single play consists of all occupants in the vehicle listening to the same playing media over the front and rear speakers. When the DVD system is on, and the same source is playing through the front and rear speakers, SINGLE PLA Y will appear in the front radio display .
Press the Headphone Control button A to change the audio source for Channel A. Press MEDIA to change the audio source for Channel A. This information will display on the DVD system screen. Press the Headphone Control button B to change the audio source for Channel B.
Press the Headphone Control button A to change the audio source for Channel A. Press MEDIA to change the audio source for Channel A. This information will display on the DVD system screen. Press the Headphone Control button B to change the audio source for Channel B.
Menu mode Press MENU once on the DVD system to access the DVD disc menu if available. Press MENU twice to access the DVD set-up menu and the following features: 1. ZOOM 2. ANGLE 3. ASPECT RA TIO 4. LANGUAGE 5. SUB TITLES Angle mode Select ANGLE to select various angles of view for the DVD.
Y ou can select from: WIDE, LETTER BOX or P AN SCAN. Once you have made your selection, press ENTER to confirm. The LCD screen display will immediately change to your selection after the system resumes playback of the DVD. The system default is WIDE (16:9).
Once you have made your selection, press ENTER to confirm. This is disc dependent. Audio CDs T o play audio CDs on your DVD system: 1. Ensure that the vehicle is on or the ignition is in accessory mode. 2. Ensure that the DVD system is on. 3. Insert an audio CD into the DVD system, label side up.
4. The folder , track and elapsed time will appear in the status bar . The screen will list the Artist, T itle, Album and File Name. COMP (Compression): Compression brings soft and loud CD/MP3 passages together for a more consistent listening level when in CD mode.
CD, MP3 and CD player care • Handle discs by their edges only . Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended periods of time. • Do not insert more than one disc into the slot of the CD player (if equipped).
Playing a DVD 1. Ensure that the vehicle is on or the ignition is in accessory mode. 2. Ensure that the navigation system is on. 3. Insert a DVD label-side up into the system. 4. Use the DVD bezel controls to: Press to play or pause a DVD. Press to stop or eject a DVD.
Frame by frame 1. W ith a DVD playing, press pause. 2. Press the right cursor button. The DVD will advance one frame. Each press of the right cursor button will advance the DVD video by one frame. Headphone/auxiliary jacks There are wired headphones (not included) and auxiliary jacks on the left and right side of your DVD system.
The B headphone jack (5) is located on the right side of the DVD system. Plug in wired headphones (not included) here. Note: The B headphones can only access DVD and AUX modes. They cannot access radio sources. Audio displays Y our DVD system interacts closely with the front audio system.
There are three levels of control of the FES buttons. The states are FULL (enabled), LOCAL or LOCKED (disabled). T o change the level of control, press the memory preset controls 3 and 5 simultaneously on the front audio controls. The control level will cycle each time the buttons are pressed simultaneously .
rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
W ARNING: The driver should not attempt to operate any function of the DVD system while the vehicle is in motion. Give full attention to driving and to the road.
Care and service of the DVD player Environmental extremes DVD players which are subjected to harsh environmental conditions may be damaged or perform at less than maximum capability . T o avoid these outcomes, whenever possible avoid exposing your DVD player to: • extremely hot or cold temperatures.
Cleaning DVD and CD discs Inspect all discs for contamination before playing. If necessary , clean discs only with an approved DVD and CD cleaner and wipe from the center out to the edge.
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REAR PASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear thin ice or fog from the windshield.
5. R Rear fan speed control: Press to enable the auxiliary system or to adjust the rear fan speed from the front control. Press to manually increase or decrease the fan speed. When the rear fan button is pressed, the display will show only the rear cabin settings.
17. EXT : Press to display the outside temperature. Press again to display the cabin temperature settings. Note: Exterior readings are more accurate when the vehicle is moving. 18. REAR: Press to enable the control located in the rear of the floor console.
4. R Rear defroster: Press to activate/deactivate the rear window defroster . Refer to Rear window defroster later in this chapter for more information. 5. R Rear fan speed control: Press to enable the auxiliary system or to adjust the rear fan speed from the front control.
13. OFF: Outside air is shut out and the climate system is turned off. 14. Driver temperature control: Press to increase or decrease the temperature on the driver side of the cabin. Sets the passenger side temperature also when DUAL is disengaged. Note: The recommended vehicle cabin setting is between 72°F (22°C) and 75°F (24°C).
• During extreme high ambient temperatures when idling stationary for extended periods of time in gear , it is recommended to run the A/C with recirculation mode selected, turn off the rear A/C unit.
AUXILIARY CLIMATE CONTROL (IF EQUIPPED) 1. Fan speed: T urn to select the desired fan speed. 2. T emperature/mode selection: The distribution of air from the overhead and floor registers is based on the temperature selected. T urn to select for comfort.
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Rotate back to to turn the headlamps off. Autolamp control The autolamp system provides light sensitive automatic on/off control of the exterior lights normally controlled by the headlamp control.
Fog lamp control The headlamp control also operates the fog lamps. The fog lamps can be turned on when the headlamp control is in the , or positions and the high beams are not turned on. Pull the headlamp control towards you to turn the fog lamps on. The fog lamp indicator light will illuminate.
W ARNING: Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
• (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp (indicated by a 3.0 mm circle on the lens) to the ground and mark an 8 foot (2.
TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Front row map lamps T o turn on the map lamps, press the outer edge of the clear lens. The front row map lamp lights when: • any door is opened.
Second row map lamps The second row map lamps are located in the headliner above the second row seats. The second row map lamp lights when: • any door is opened, • the instrument panel dimmer switch is rotated up until the courtesy lamps come on, and • any of the remote entry controls are pressed and the ignition is off.
BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold.
Function Number of bulbs T rade number 2nd row reading lamp 1 1600XB Rear cargo lamp 1 211–2XB Rear turn/tail/brake lamps 4 4057K Backup lamps 2 921 Supplemental tail lamps 4 906 Approach lamps 2 90.
3. At the back of the headlamp lens, remove the two headlamp assembly bolts. 4. Pull the headlamp assembly forward slightly to expose the electrical connectors. 5. Rotate the bulb socket counterclockwise and remove. 6. Pull the bulb straight out of the socket and push in the new bulb.
1. Make sure the headlamp switch is in the off position. 2. Open the liftgate to expose the lamp assembly screws. 3. Remove the two screws from the lamp assembly . 4. Carefully pry the lamp assembly away from the vehicle by pulling the assembly directly straight out to expose the bulb socket.
Replacing the high-mount brakelamp T o change the high-mount brakelamp bulbs: 1. Remove the two screws holding the lamp assembly in place. 2. Pull the lamp assembly straight out. 3. Disconnect the wire harness. 4. Press the four tabs that hold the light assembly on, one at a time, and pull the black bulb carrier away from the lamp.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Speed dependent wipers: When the wiper control is on, the speed of the wipers will automatically adjust with the vehicle speed.
Courtesy wipe feature: One extra wipe will occur a few seconds after washing the front window to clear any excess washer fluid remaining on the windshield. Note: Do not operate the washer when the washer reservoir is empty . This may cause the washer pump to overheat.
POWER TILT STEERING The steering column can be adjusted manually by moving the two-way rocker adjustment control located below the turn signal/wiper control stalk. Hold the control to adjust. The tilt function is adjusted by depressing the control up or down.
On vehicles with memory feature, to prevent damage to the steering column, the steering column is designed to set a stopping position just short of the end of the column position. If the steering column encounters an object while moving up or down, a new stopping position will be set.
OVERHEAD CONSOLE The appearance of your vehicle’ s overhead console will vary according to your option package. Forward storage bin (if equipped) The storage compartment may be used to store a pair of sunglasses. Press the release area on the rear edge of the bin door to open the storage compartment.
Power quarter rear windows Press the VENT portion of the control to open the power rear quarter windows. Pull the VENT control to close the power rear quarter windows.
CLOCK Press the right (+) control to move the time display forwards. Press the left (-) control to move the time display backwards. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse.
POWER WINDOWS W ARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. W ARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.
T o operate one touch up: Pull the switch completely up to the second detent and release quickly . The window will close fully . Momentarily press the switch to any position to stop the window operation. If the switch is pressed and held to the normal open or one touch down position during a one touch up event, the window will stop.
INTERIOR MIRROR The interior rear view mirror has two pivot points on the support arm which lets you adjust the mirror up or down and from side to side.
EXTERIOR MIRRORS Power side view mirrors The ignition can be in any position to adjust the power side view mirrors. T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror .
Note: 10 or more switch activations within one minute, or repeated folding/unfolding of the mirrors while holding the switch rearward during full travel, may cause the system to disable the fold/unfold function to protect motors from overheating.
W ARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. POWER DEPLOYABLE RUNNING BOARDS (IF EQUIPPED) Deployable running boards (DRB) automatically move when the doors are opened to assist entering and exiting the vehicle.
Note: The running boards may operate slower in cooler temperatures. In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running board mechanism, possibly leading to unwanted noise.
Using speed control The speed controls are located on the steering wheel. The following buttons work with speed control: RESUME: Press to resume a set speed. SET +: Press to increase the set speed. S E T–: Press to decrease the set speed. OFF/ON: Press to turn speed control off or on.
Increasing speed while using speed control T o set a higher speed: • Press and hold SET + until you get to the desired speed, then release. Y ou can also use SET + to operate the tap-up function. Press and release SET + to increase the vehicle set speed in 1 mph (1.
SYNC 威 system hands free control features Press briefly to use the voice command feature. Y ou will hear a tone and LISTENING will appear in the radio display . Press and hold to exit voice command. Press to activate phone mode or answer a phone call.
T o open the moon roof: Press and release the SLIDE control, the moon roof will open automatically . Press the switch again to stop the moon roof. W ARNING: When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the moon roof opening.
HomeLink 威 Car2U 威 Home Automation System HomeLink 姞 Wireless Control System (if equipped) The HomeLink 威 W ireless Control System, located on the driver’ s visor , provides a convenient way to replace up to three hand-held transmitters with a single built-in device.
Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink 威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink 威 buttons be erased for security purposes, refer to Programming in this section.
5. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer .) Note: There are 30 seconds in which to initiate Step 6. 6. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink 威 button.
Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button. Activation will now occur for the trained product (garage door , gate operator , security system, entry door lock, or home or office lighting etc.
Car2U 姞 Home Automation System (if equipped) The Car2U 威 Home Automation System is a universal transmitter located in the driver’ s visor that includes two primary features – a garage door opener and a platform for remote activation of devices within the home.
T ypes of garage door openers (rolling code and fixed code) The Car2U 威 Home Automation System may be programmed to operate rolling code and fixed code garage door openers. • Rolling code garage door openers were produced after 1996 and are code protected.
1. Firmly press the two outer Car2U 威 system buttons for 1–2 seconds, then release. 2. Go to the garage to locate the garage door opener motor and its “learn” button. Y ou may need a ladder to reach the unit and you may need to remove the unit’ s cover or light lens to locate the “learn” button.
The indicator light above the selected button will turn on to confirm that the Car2U 威 system is responding to the button command. T o program another rolling code device such as an additional garag.
Switch position 1234567 8 91 0 1 1 1 2 Up, on or + LLLLLLL LLLLL Middle, neutral or 0 MMMMMMM M M M M M Down, o f fo r– RRRRRRR RRRRR L=left; M=middle; R=right 3. T o input these positions into the Car2U 威 system, simultaneously press all three Car2U 威 system buttons for a few seconds and then release to put the device into programming mode.
After successful programming, you will be able to operate your Car2U 威 system by pressing the button you programmed to activate the opener . The indicator light above the selected button will turn on to confirm that the Car2U 威 system is responding to the button command.
POWER LIFTGATE The liftgate can be operated by the following: • Instrument panel control button • Key fob button • Outside control button • Control button in the rear cargo area Note: The liftgate can be reversed with a second press on a control button or key fob and can be manually closed at any time.
Care should be exercised in starting the engine before the liftgate is fully closed (latched). If the ignition is cycled during a liftgate power close cycle and the liftgate is 6-10 inches (15–24 cm) from being latched, the liftgate may reverse to the full open position.
T o close the liftgate with the rear cargo area control button: Press and release the control on the left rear quarter panel to close the liftgate. The chime will beep once if conditions are not correct to start an operation (i.e., the vehicle is out of park).
Note: In case of operation in extreme cold -40° F (-40° C), or on extreme inclines, manual operation of the liftgate is suggested. Obstacle detection The power liftgate system is equipped with an obstacle detection feature. If the power liftgate is closing, the system is designed to reverse to full open when it encounters a solid obstacle.
Liftgate window T o open the liftgate window , press the button on the left side of the liftgate above the license plate. CARGO MANAGEMENT SYSTEM (IF EQUIPPED) The cargo management system consists of a storage compartment located in the floor of the rear cargo area.
T o move the shelf to the divider position, pull up and pivot the shelf over the channels on the side trim panels and snap vertically in place. W ARNING: Do not load any objects on the shelf that may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision.
T o adjust the position of the cross-bar (if equipped): 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. Firmly retighten the thumbwheels at each end of the cross-bar .
KEYS Y our vehicle may be equipped with two Integrated Keyhead T ransmitters (IKT s). The key blade functions as a programmed key which starts the vehicle and unlocks/locks all the doors. The transmitter portion functions as the remote entry transmitter .
POWER DOOR LOCKS Press control to unlock all doors. Press control to lock all doors. Smart locks This feature helps to prevent you from locking yourself out of the vehicle if your key is still in the ignition.
The autolock feature repeats when: • any door is opened then closed while the ignition is in the on position and the vehicle speed is 9 mph (15 km/h) or lower , and • the vehicle attains a speed greater than 12 mph (20 km/h). Deactivating/activating autolock Y our vehicle comes with the autolock feature enabled.
Keyless entry keypad procedure 1. T urn the ignition to the off position. 2. Close all doors, the liftgate and liftgate window . 3. Enter 5–digit entry code 4. Press and hold the 3 • 4. While holding the 3 • 4p r e s st h e7 • 8. 5. Release the 7 • 8.
Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the off position and all vehicle doors are closed. Y ou must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again.
CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
The typical operating range for your IKT is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle.
T wo stage unlocking may be disabled or re-enabled by simultaneously pressing the and controls on the IKT for four seconds (disabling two stage unlock allows all vehicle doors to unlock simultaneously). The parking lamps will flash twice to indicate that two-stage unlock was enabled or disabled.
Sounding a panic alarm Press to activate the alarm. The horn will sound and the turn lamps will flash for a maximum of three minutes. Press again or turn the ignition to the on position to deactivate, or wait for the alarm to time out in three minutes.
3. A tone will be heard when the deactivation is complete. 4. Repeat this procedure for another remote entry transmitter if desired. Replacing the battery The Integrated Keyhead T ransmitter uses one coin type three-volt lithium battery CR2032 or equivalent.
Illuminated entry The interior lamps, parking lamps and puddle lamps (if equipped) illuminate when the Integrated Keyhead T ransmitter or the keyless entry system keypad is used to unlock the door(s).
• activate or deactivate the Autolock feature if equipped • release the liftgate glass, The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’ s wallet card in the glove box and is available from your authorized dealer .
The anti-scan feature will turn off after: • one minute of keypad inactivity , • pressing the control on the remote entry transmitter , • or the ignition position changes. Unlocking and locking the doors and liftgate using keyless entry T o unlock the driver’ s door , enter the factory set 5-digit code or your personal code.
engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded IKT and restart the engine. Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle.
Replacement Integrated Keyhead T ransmitters (IKT) and coded keys Note: Y our vehicle comes equipped with two Integrated Keyhead T ransmitters (IKT s). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, as well as a remote keyless entry transmitter .
Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition. 2. T urn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least three seconds, but no more than 10 seconds.
Note: T o program MyKey™ features, refer to MyKey™ in this chapter . MYKEY™ The MyKey™ feature allows you to program a restricted driving mode to promote good driving habits. All but one of the keys programmed to the vehicle can be activated as a MyKey™.
Create a MyKey™ T o program MyKey™ on one of the keys programmed to the vehicle, insert it into the ignition. T urn the ignition on. Use the message center buttons to do the following: 1. Press SETUP until PRESS RESET TO CREA TE MYKEY is displayed.
Disable MyKey™ T o reset all MyKeys™ as Admin keys do the following: 1. T urn the vehicle on using the Admin key . 2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed. 3. Press and release the RESET button. HOLD RESET TO CONFIRM CLEAR is displayed.
T roubleshooting Condition Potential Causes Can’t create a MyKey™ • Key in the ignition is already a MyKey™ • Key in the ignition is the last remaining Admin key (there always has to be at l.
The system is ready to arm whenever the key is in the off position, or is removed from the ignition. Either of the following actions will prearm the alarm system: • Press the control on the remote entry transmitter portion of your Integrated Keyhead T ransmitter .
Disarming the system Y ou can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter portion of your Integrated Keyhead T ransmitter .
SEA TING Adjustable head restraints Y our vehicle is equipped with front row outboard head restraints that are vertically adjustable. W ARNING: T o minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position.
3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint. Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head.
2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint. T o reinstall the adjustable head restraint, do the following: 1. Insert the two stems into the guide sleeve collars. 2. Push the head restraint down until it locks.
Using the power lumbar support The power lumbar control is located on the outboard side of the seat. Press the forward side of the control for additional support. Press the rear side of the control to reduce support. Adjusting the front power seat W ARNING: Never adjust the driver’ s seat or seatback when the vehicle is moving.
Move the switch in the direction of the arrows to raise or lower the rear portion of the seat cushion. Press the switch in the direction of the arrows to move the seat forward, backward, up or down. Press the control to recline the seatback forward or rearward.
Memory seat/power mirrors/adjustable pedals/steering column This system allows automatic positioning of the driver seat, outside rearview mirrors, adjustable pedals, and steering column to two programmable positions. The memory seat control is located on the outboard side of the seat cushion.
Heated seats W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
Climate controlled seats air filter replacement (if equipped) The climate controlled seat system includes air filters that must be replaced periodically . Refer to the scheduled maintenance information for more information. • There is a filter located under each front seat.
T o install a filter: • First, position the filter in it’ s housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
2. Locate handle on the side of the seat cushion by the door . 3. Pull up on the handle and push the seatback forward toward the front of the vehicle. T o return the seat to the upright position: 1. Lift the seatback toward the rear of the vehicle. 2.
Placing the 2nd row outboard 40% seats in cargo mode W ARNING: Use caution when folding the seatback to the flat back position as the system will move forward when you lift the release handle. The 2nd row seats can be placed in a kneel down load floor position to allow more cargo space.
Returning to the upright position from full lowered load floor position The seatback cannot be returned to the upright position until the seat is returned from the kneel down position. T o return the seat to the upright position: 1. Push the seat rearward until the latch is engaged.
T o return the seat to a seating position: 1. Push the seat down and latch to the floor with a moderate amount of effort and speed. 2. Make sure the seat is latched to the floor . 3. Bring the seat back to an upright position. The seatback should lock into position.
Exiting the 3rd row 1. Pull the strap located at the bottom outboard of the seat back to release the seat from the floor , and rotate the seat up towards the front seat. 2. Follow the directions above to return the seat from the E-Z entry and to the upright position.
W ARNING: T o prevent possible damage to the seat or safety belts, ensure that the safety belts are not buckled when moving the seat to the load floor position. 2. W ith the latch released the seatback can be lowered into the load floor position. 3. T o return the seat to the upright position, lift the seatback until the latch is fully engaged.
Adjusting the 2nd row center 20% seat (if equipped) Lift the handle to move the seat forward or backward. Note: This seat can be moved forward to keep a child in a child restraint close to the front seat occupants.
T o operate the heated seats: • Push the indicated side of the control for maximum heat. • Push again to deactivate. • Push the indicated side of the control for minimum heat. • Push again to deactivate. The heated seat module resets at every ignition run cycle.
Folding down the 3rd row seats to the load floor W ARNING: T o prevent possible damage to the seat or safety belts, ensure that the safety belts are not buckled when moving the seat to the load floor position. Before folding the third row seats, fold the head restraints down by pulling on the strap located at the bottom of the restraint.
Third row power folding seat (if equipped) Note : Be sure that the head restraints are folded down before powering the 3rd row seat down. The control buttons are located on the right-hand rear quarter trim panel (accessible from the liftgate area). Push the bottom portion of the control button to lower the desired seatback.
The power fold down seats will operate for 10 minutes after the ignition switch is in off. The transmission must be in P (Park), and the liftgate, or liftgate glass must be open. Similar to the battery saver feature, the power 3rd row seat will be disabled 10 minutes after turning the vehicle off.
The fact that the pretensioners or airbags did not activate for both front seat occupants in a collision does not mean that something is wrong with the system. Rather , it means the Personal Safety System 威 determined the accident conditions (crash severity , belt usage, etc.
Front safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’ s forward momentum.
W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. W ARNING: All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an airbag supplemental restraint system (SRS) is provided.
Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. • Front and rear seats 2.
Webbing extraction sensitive mode The webbing sensitive locking mode locks the webbing and prevents more belt from being pulled out if the belt is pulled out too quickly . The belt will unlock when you stop pulling on it. Automatic locking mode In this mode, the shoulder belt is pre-locked.
How to disengage the automatic locking mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and return to the vehicle sensitive (emergency) locking mode.
Safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and right front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, squeeze the side release buttons with your thumb and finger and slide the height adjuster down.
T o adjust the comfort guide: 1. Slip the shoulder belt into the belt guide. (The portion of the belt between the latch tongue and the D-ring, not the portion where the belt exits from the quarter trim panel.) 2. Slide the guide up or down along the webbing so that the belt is centered on the occupant’ s shoulder .
Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver safety belt is not buckled before the ignition switch is turned to the on position.
If... Then... The driver’ s safety belt is not buckled approximately five seconds after the safety belt warning light has turned off... The Belt-Minder 威 feature is activated - the safety belt war.
Reasons given... Consider ... “Belts are uncomfortable” W e design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort.
W ARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. T o do so may adversely affect the performance of the vehicle’ s air b.
4. W ithin approximately seven seconds of the light turning off, buckle then unbuckle the safety belt. • This will disable the Belt-Minder 威 feature for that seating position if it is currently enabled. As confirmation, the safety belt warning light will flash four times per second for three seconds.
W ARNING: All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. W ARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position.
W ARNING: Additional equipment may affect the performance of the airbag sensors increasing the risk of injury . Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.
• one or more impact and safing sensors and diagnostic monitor (RCM), • a readiness light and tone • the electrical wiring which connects the components.
W ARNING: Do not attempt to service, repair , or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. Contact your authorized dealer as soon as possible. W ARNING: All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.
The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activation.
W ARNING: Do not attempt to service, repair , or modify the Safety Canopy 威 system, its fuses, the A, B, C or D pillar trim, or the headliner on a vehicle containing a Safety Canopy 威 .
• T wo crash sensors mounted in the front doors (one on each side of the vehicle). • T wo crash sensors located at the C pillar behind the rear doors (one on each side of the vehicle).
W ARNING: If the Safety Canopy 威 system has deployed, the Safety Canopy 威 will not function again unless replaced. The Safety Canopy 威 system (including the A, B, C, and D pillar trim and headliner) must be inspected and serviced by an authorized dealer .
The SOS Post-Crash Alert can be turned off when any one of the following actions are taken by the driver or any other person: • pressing the hazard control button, • or pressing the panic button on the remote entry transmitter . The feature will continue to operate until the vehicle runs out of power .
Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger) Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat).
Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA.
W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury or death. W ARNING: Never use pillows, books, or towels to boost a child.
If the child is the proper height, age, and weight (as specified by your child safety seat or booster manufacturer), fits the restraint and can be restrained properly , then restrain the child in the child safety seat or with the belt-positioning booster .
Installing child safety seats with combination lap and shoulder belts Check to make sure the child seat is properly secured before each use. Children 12 and under should be properly restrained in a rear seating position whenever possible.
1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
9. Attach the tether strap (if the child seat is equipped). Refer to Attaching child safety seats with tether straps later in this chapter . 10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place.
Y our vehicle has LA TCH lower anchors for child seat installation at the seating positions marked with the child seat symbol. The LA TCH anchors are located at the rear section of the rear seat between the cushion and seatback, below the locator symbols on the seat back.
W ARNING: Never attach two child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death.
The tether strap anchors in your vehicle are in the following positions (shown from top view): • Second row bench seat • Second row bucket seats Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor .
• Second row outboard seating positions • Second row center seating position (if equipped) 3. Grasp the tether strap and position it to the seat frame.
5. Rotate the tether strap clip. 6. T ighten the child safety seat tether strap according to the manufacturer’ s instructions. Third row center seating position 1.
3. Clip the tether strap through the anchor loop as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 4. T ighten the child safety seat tether strap according to the manufacturer’ s instructions.
Booster seats position a child so that vehicle lap/shoulder safety belts fit better . They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably at the edge of the cushion, while minimizing slouching. Booster seats may also make the shoulder belt fit better and more comfortably .
T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield.
Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision.
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter .
• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition.
T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100.
TIRES T ires are designed to give many thousands of miles of service, but they must be maintained in order to get the maximum benefit from them. Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry .
INFLATING Y OUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required.
The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or T ire Label. When weather temperature changes occur , tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure.
TIRE CARE Inspecting your tires and wheel valve stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves.
W ARNING: Age T ires degrade over time depending on many factors such as weather , storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear .
W ARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford.
It is recommended that the two front tires or two rear tires generally be replaced as a pair . The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels.
Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment.
Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire’ s load index. It is an index that relates to how much weight a tire can carry .
8. U.S. DOT T ire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built.
13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
The T ire Pressure Monitoring System complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Understanding your Tire Pressure Monitoring System (TPMS) The T ire Pressure Monitoring System measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The Low T ire Pressure W arning Lamp will turn ON if the tire pressure is significantly low .
When you believe your system is not operating properly The main function of the T ire Pressure Monitoring System is to warn you when your tires need air .
Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use.
SNOW TIRES AND CHAINS W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover , personal injury and death.
capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, familiarize yourself with the following t.
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
W ARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.
to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb.
• Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter . • Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter . • Service your vehicle more frequently if you tow a trailer .
Engine Rear axle ratio Maximum GCWR - lb. (kg) T railer weight range (0 - maximum) - lb. (kg) 4x2 5.4L with standard trailer tow package All 12000 (5443) 0–6000 (0–2721) 5.4L with optional trailer tow package All 15000 (6804) 0–9000 (0–4082) 4x4 5.
Engine Rear axle ratio Maximum GCWR - lb. (kg) T railer weight range (0 - maximum) lb. (kg) Navigator L 4x2 5.4L with standard trailer tow package All 12300 (5579) 0–6000 (0–2721) 5.4L with optional trailer tow package All 15000 (6804) 0–8700 (0–3946) Navigator L 4x4 5.
Integrated hitch rating The standard integrated hitch has two ratings depending on mode of operation: • W eight carrying - requires a draw bar and hitch ball.
2. T o reinstall the cover , insert the four plastic tabs on top of the cover into the corresponding slots, as shown in the illustration and push the cover up into the bumper trim. 3. Hold the cover against the bumper trim and reinstall the two 1 ⁄ 4 -turn fasteners by turning them clockwise.
4. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within a 1 ⁄ 2 ” (13 mm) of the reference point. After proper adjustment, the rear bumper should be no higher than in Step 3. 5. T urn the air suspension (if equipped) control to on.
Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (113 km/h) during the first 500 miles (800 km) of towing a trailer , and don’t make full throttle starts. • T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades.
• If you will be towing a trailer frequently in hot weather , hilly conditions, at GCWR, or any combination of these factors, consider refilling your rear axle with synthetic gear lube if not already so equipped. Refer to the Maintenance and Specifications chapter for the lubricant specification.
RECREATIONAL TOWING Follow these guidelines if you have a need for recreational towing. An example of recreational towing would be towing your vehicle behind a motorhome.
STARTING Positions of the ignition 1. Off— locks the steering wheel, automatic transmission gearshift lever and allows key removal. 2. Accessory— allows the electrical accessories such as the radio to operate while the engine is not running. 3. On— all electrical circuits operational.
W ARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM).
4. Make sure the parking brake is set. 5. T urn the key to 3 (on) without turning the key to 4 (start). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights.
3. After idling for a few seconds, release the parking brake, apply the brake, shift into gear and drive. Note: If the engine does not start on the first try , turn the key to the off position, wait 10 seconds and try Step 2 again.
Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects. W ARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes.
W ARNING: Failure to follow engine block heater instructions could result in property damage or physical injury . W ARNING: T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters.
• Finally , have the engine block heater system checked during your fall tune-up to be sure it’ s in good working order . How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. T o clean them, use a dry cloth.
Anti-lock brake system (ABS) On ABS-equipped vehicles, a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events.
Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned on) until the parking brake is released.
Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . ADVANCET RAC 姞 WITH ROLL STABILITY CONTROL™ (RSC .
W ARNING: If a failure has been detected within the AdvanceT rac 威 with RSC 威 system, the ⬙ sliding car ⬙ icon will illuminate steadily . V erify that the AdvanceT rac 威 with RSC 威 system is not manually disabled (push the AdvanceT rac 威 with RSC 威 “Off “ button located on the center of the instrument panel).
Note: If the system cannot be turned off, refer to MyKey™ in the Locks and Security chapter for more information. When AdvanceT rac 威 with RSC 威 performs a normal system self-check, some drivers may notice a slight movement of the brake, and/or a rumble, grunting, or grinding noise after startup and when driving off.
Electronic Stability Control (ESC) Electronic Stability Control (ESC) may enhance your vehicle’ s directional stability during adverse maneuvers, for example when cornering severely or avoiding objects in the roadway .
Switching Off T raction Control If the vehicle is stuck in snow , mud or sand, and seems to lose engine power , switching off the T raction Control feature of the AdvanceT rac 威 with RSC 威 system may be beneficial because the wheels are allowed to spin.
During trailer sway control events the “sliding car” icon in the instrument cluster will flash momentarily . The cluster message center will also display TRAILER SW A Y REDUCE SPEED . In some cases when trailer sway is detected, the vehicle speed is too high and may be above a speed at which trailer sway will not grow continuously .
If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually , but it takes more effort. If the steering wanders or pulls, check for: • Underinflated.
the system determines that the vehicle is low or high and needs to make a height adjustment while driving at speeds above 15 mph (24 km/h), the system will pump or vent as required.
BRAKE-SHIFT INTERLOCK – FLOOR-SHIFT TRANSMISSION This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the on position unless the brake pedal is pressed.
W ARNING: Do not drive your vehicle until you verify that the brakelamps are working. W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the off position and remove the key whenever you leave your vehicle.
P (Park) This position locks the transmission and prevents the rear wheels from turning. T o put your vehicle in gear: • Press the brake pedal • Start the engine • Move the gearshift lever into the desired gear .
D (Overdrive) with T ow/Haul On The T ow/Haul feature improves transmission operation when towing a trailer or a heavy load. All transmission gear ranges are available when using T ow/Haul. T o activate T ow/Haul, press the button on the side of the gearshift lever .
3 (Third) T ransmission operates in third gear only . Used for improved traction on slippery roads. Selecting 3 (Third) provides engine braking. 2 (Second) T ransmission operates in 2nd gear only . Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades.
FORWARD AND REVERSE SENSING SYSTEMS The forward and reverse sensing system will warn the driver of obstacles within a certain range of the front and rear bumpers. The front sensors will be active when the gearshift is in any position other than P (Park) or N (Neutral) and the vehicle speed is below 8 mph (13 km/h).
The reverse sensing portion of the system detects obstacles up to 6 ft. (2 m) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the illustration for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
W ARNING: This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.
Note: If the system cannot be turned off, refer to MyKey™ in the Locks and Security chapter for more information. The system defaults to enabled every time the ignition is switched on.
Use the side mirrors and rearview mirror to get better coverage on both sides and rear of the vehicle. Image delay if displayed through the rearview mirror: When shifting out of R (Reverse) and into any other gear , the image in the rearview mirror will remain on for a few seconds before it shuts off to assist in parking or trailer hookup.
W ARNING: Do not use the camera system with the liftgate open. If the back end of the vehicle is hit or damaged, then check with your authorized dealer to have your rear video system checked for proper coverage and operation.
• 4X2 - Momentarily illuminates when 2H is selected. • 4X4 AUTO – Illuminates when 4X4 AUTO is selected. • 4X4 – Illuminates when 4X4 is selected. Modes of the Control T rac system The Control T rac system functions in three modes: • 4X2 (2WD) delivers power to the rear wheels only .
maneuvers. This will disable the engine management feature, allowing the vehicle to maintain full power and enhanced momentum through the obstacle. W ARNING: Utility and four -wheel drive vehicles are.
Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps.
If your vehicle gets stuck If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear . Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur .
W ARNING: V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity .
A void excessive speed because vehicle momentum can work against you and cause the vehicle to become stuck to the point that assistance may be required from another vehicle. Remember , you may be able to back out the way you came if you proceed with caution.
“T read Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas.
Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear . When descending a steep hill, avoid sudden hard braking as you could lose control.
W ARNING: If you are driving in slippery conditions that require tire chains or cables, then it is critical that you drive cautiously . Keep speeds down, allow for longer stopping distances and avoid aggressive steering to reduce the chances of a loss of vehicle control which can lead to serious injury or death.
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursemen.
Note: W ith extended use, the flasher may run down your battery . FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt.
FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating.
Passenger compartment fuse panel The fuse panel is located under the right-hand side of the instrument panel. T o remove the trim panel for access to the fuse box, pull the panel toward you and swing it out away from the side and remove it. T o reinstall it, line up the tabs with the grooves on the panel, then push it shut.
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protective Circuits 1 30A Smart window #1 2 15A Driver side memory module 3 15A Family entertainment system, Audio rear seat control.
Fuse/Relay Location Fuse Amp Rating Protective Circuits 23 15A High beam headlamps 24 20A Horn 25 10A Demand lamps, Glovebox, Visor 26 10A Instrument panel cluster 27 20A Ignition switch 28 5A Radio 2.
Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. W ARNING: Always disconnect the battery before servicing high current fuses.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 4 — T railer tow battery charge relay 5 — Fuel pump relay 6 — Electronic fan 1 relay 7 — Rear window defroster/heated mirror relay 8 — .
Fuse/Relay Location Fuse Amp Rating Protected Circuits 32 40A** Blower motor relay 33 — Not used 34 30A** Auxiliary blower motor 35 30A** PCM relay 36 30A** Power liftgate 37 — T railer tow left h.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 59 15A* Heated mirrors 60 — One-touch start diode 61 — Fuel pump diode 62 — Left HID headlamp relay 63 25A** Electronic fan 64 30A** Moon r.
CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use.
2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONL Y” When driving with one of the dissimilar spare.
• W et weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional.
Removing the jack and tools 1. Open the liftgate, then locate the access panel on the floor behind the 3rd row seat. Unlatch and remove the panel. 2. Remove the jack and tools assembly tray from the compartment by turning the wing-nut counterclockwise to relieve tension against the jack assembly tray .
Tire change procedure W ARNING: T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block the wheels (both front or both rear) on the opposite end of the vehicle from the wheel being changed. If on a grade, block both opposite wheels on the downward side of the hill.
1. Block the wheels (both front or both rear) on the opposite end of the vehicle from the wheel being changed. If on a grade, block both wheels on the downward side of the hill. 2. T urn off the air suspension system. The air suspension system is controlled through the message center .
W ARNING: When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park).
• Never use the front or rear differential as a jacking point. W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.
2. Slide the wheel partially under the vehicle and install the retainer through the wheel center . If equipped, you may have to remove the wheel center cap prior to pushing the retainer through the center of the wheel. T o remove the center cap, press it off with the jack tool from the inner side of the wheel.
W ARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel.
JUMP STARTING W ARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. W ARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.
Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
4. Make the final connection of the negative (-) cable to the jump starting stud located in the engine compartment, near the washer fluid bottle. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points.
Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery .
4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
If the vehicle is towed by other means or incorrectly , vehicle damage may occur . Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .
In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . If a warranty concern has not been resolved using the three-step procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program.
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the au.
If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: FORD MOTOR COMP ANY FORD EXPORT OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
Exterior chrome • W ash the vehicle first, using cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3-A). • Use Custom Bright Metal Cleaner (ZC-15), available from your authorized dealer .
• Never apply any cleaning chemical to hot or warm wheel rims or covers. • Some automatic car washes may cause damage to the finish on your wheel rims or covers. Chemical-strength cleaners, or cleaning chemicals, in combination with brush agitation to remove brake dust and dirt, could wear away the clearcoat finish over time.
• Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer .
INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with a clean, damp, white cotton cloth, then use a clean and dry white cotton cloth to dry these areas. • A void cleaners or polishes that increase the gloss of the upper portion of the instrument panel.
• If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14). In Canada, use Motorcraft Multi-Purpose Cleaner (CXC-101). • If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set.
UNDERBODY Flush the complete underside of your vehicle frequently . Keep body and door drain holes free from packed dirt. FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes.
SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
Working with the engine on 1. Set the parking brake and shift to P (Park). 2. Block the wheels. W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L V8 1. W indshield washer fluid reservoir 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Power distribution box 8.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
CHANGING THE WIPER BLADES It is recommended that wiper blades are renewed before winter . T o replace the wiper blades: 1. Fold back the wiper arm and position the wiper blade at right angles to the wiper arm.
4. T o attach the new wiper to the wiper arm, align the cross pin and keyway (denoted with the arrows) and firmly press the wiper blade into the wiper arm until an audible snap is heard. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil.
• If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter . • Do not overfill the engine with oil.
Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API).
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced.
W ARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. A void contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution.
• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the FULL COLD level or within the COLD FILL RANGE as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules.
• Do not mix coolants. Add the coolant type originally equipped in your vehicle. Refer to Maintenance product specifications and capacities in this chapter . Note: Do not use stop leak pellets or cooling system sealants/additives as they can cause damage to the engine cooling and/or heating systems.
4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, to within the COLD FILL RANGE or the FULL COLD level on the reservoir .
• NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase.
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions W ARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.
• Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water . Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation.
W ARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes.
When fueling your vehicle: 1. T urn the engine off. 2. Open the fuel filler door . 3. Slowly insert the fuel filler nozzle fully into the fuel system. Pump fuel as normal. 4. After you are done pumping fuel, slowly remove the fuel filler nozzle—allow about five seconds after pumping fuel before removing the fuel filler nozzle.
The use of leaded fuel is prohibited by law and could damage your vehicle. Y our vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives.
tank if you continue to use high quality fuel of the recommended octane rating. These products have not been approved for your engine and could cause damage to the fuel system. Repairs to correct the effects of using an aftermarket product in your fuel may not be covered by your warranty .
W ARNING: Do not try to pry open or push open the Easy Fuel™ system with foreign objects. This could damage the fuel system and its seal and cause injury to you or others. When filling the vehicle’ s fuel tank from a portable fuel container , use the included funnel.
The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty . Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty .
Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’ s fuel economy under current driving conditions. Additionally , keeping records during summer and winter will show how temperature impacts fuel economy .
• Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed.
• Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in scheduled maintenance information performed according to the specified schedule.
On board diagnostics (OBD-II) Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD-II). The OBD-II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
If the service engine soon indicator is on or the bulb does not work, the vehicle may need to be serviced. Refer to the On board diagnostics (OBD-II) description in this chapter .
5. If the fluid is low , add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir . Refer to Maintenance product specifications and capacities in this chapter for the proper fluid type.
W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1. Locate the mass air flow sensor electrical connector on the air outlet tube.
5. Release the three clamps that secure the cover to the air filter housing. Push the air filter cover toward the center of the vehicle and up slightly to release it. 6. Remove the air filter element from the air filter housing. 7. Install a new air filter element.
10. Reconnect the mass air flow sensor electrical connector to the outlet tube. Make sure the locking tab on the connector is in the “locked” position (connector shown from below for clarity). Note: Failure to use the correct air filter element may result in severe engine damage.
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name Ford part number / Ford specification Brake fluid Between MIN and MAX on reservoir Motorcraft High Performance DOT 3 Moto.
Item Capacity Ford part name Ford part number / Ford specification Cooling system stop leak pellets — Motorcraft Cooling System Stop Leak Pellets VC-6 / WSS-M99B37-B6 Engine oil 7.
Item Capacity Ford part name Ford part number / Ford specification Rear axle fluid–Conventional differential (9.75 inch axle) 4.5 pints (2.1L) Motorcraft SAE 75W -140 Synthetic Rear Axle Lube 5 XY -75W140-QL / WSL-M2C192-A T ransfer case fluid (4X4) 1.
ENGINE DATA Engine 5.4L V8 engine Cubic inches 330 Fuel 87 octane or (E-85) Firing order 1-3-7-2-6-5-4-8 Ignition system Coil on plug Spark plug gap 0.
Engine drivebelt routing IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
V ehicle identification number (VIN) The vehicle identification number is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number . The V ehicle Identification Number (VIN) contains the following information: 1.
T RANSMISSION CODE DESIGNATIONS Y ou can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents.
GENUINE LINCOLN ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Lincoln Accessories are available for your vehicle through your local Lincoln or Ford of Canada dealer .
Locking gas plug for capless fuel system Wheel locks For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding acces.
FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage.
Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract.
Ford Extended Service Plan 379 2010 Navigator (nav) Owners Guide (own2002) , 1st Printing USA (fus).
A ABS (see Brakes) ..................... 261 Accessory delay ........................ 105 AdvanceT rac .............................. 263 Air cleaner filter ....... 364–365, 367 Air suspension ...........................269 description .............
Child safety seats - booster seats ........................................... 211 Cleaning your vehicle engine compartment .............. 330 instrument panel ....................332 interior ............................. 332–333 plastic parts ....
Event data recording .................... 7 Exhaust fumes .......................... 258 F Fail safe cooling ........................ 349 Family entertainment system ....47 Fleet MyKey programming ...... 148 Flexible Fuel V ehicle (FFV) ....351 Fluid capacities .
J Jack ............................................ 303 positioning ............................... 303 storage ..................................... 303 Jump-starting your vehicle ...... 313 K Keyless entry system autolock ...........................
Power deployable running boards ........................................ 109 Power distribution box (see Fuses) ....................... 296, 299 Power door locks ...................... 133 Power liftgate ............................125 Power mirrors .
Spark plugs, specifications ............. 367, 371–372 Special notice utility-type vehicles .................... 6 Specification chart, lubricants ................................... 368 Speed control ............................ 110 Stability system .
Een belangrijk punt na aankoop van elk apparaat Lincoln Electric 2010 Navigator (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lincoln Electric 2010 Navigator heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lincoln Electric 2010 Navigator vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lincoln Electric 2010 Navigator leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lincoln Electric 2010 Navigator krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lincoln Electric 2010 Navigator bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lincoln Electric 2010 Navigator kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lincoln Electric 2010 Navigator . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
