Gebruiksaanwijzing /service van het product IM803-B van de fabrikant Lincoln Electric
Ga naar pagina of 31
RED-D-ARC ES 275i IM803-B August, 2006 Red-D-Ar c Spec-Built W elding Equipment This RED-D-ARC welder is built to RED-D-ARC Extreme Duty design specifications by Lincoln Electric. Safety Depends on Y ou This welder is designed and built with safety in mind.
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv Mar. ‘93 PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instruc- tions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suivantes: Sûreté Pour Soudage A L’Arc 1.
v v Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
vi vi T ABLE OF CONTENTS Page Installation ................................................................................................................... ....Section A Technical Specifications .....................................................
ES 275i A-1 INST ALLA TION A-1 Height Width Depth Weight (With Cord) 13.6in.(345mm) - Handle Folded Down 20.25 in.(514mm) 9.0 in.(229mm) 54.5lbs. (24.7Kg) 16in.
A-2 INST ALLA TION A-2 Read this entire installation section before you start installation. SAFETY PRECAUTIONS ELECTRIC SHOCK can kill. • Have an electrician install and service this equipment. • Turn the input power off at the fuse box before working on equipment.
ES 275i OUTPUT CONNECTIONS Refer to figure B.1 for the location of the 3-Pin Remote Receptacle and the Output Terminals. OUTPUT CABLES Select the output cable size based on Table A.1. TABLE A.1 Cable Sizes for Combined Length of Electrode and Work Cable ( Copper Cable Rated at 75°C).
ES 275i B-1 OPERA TION B-1 GENERAL DESCRIPTION The ES 275i is a 275 amp arc welding power source that utilizes single or three phase input power, to pro- duce constant current output. The welding response of this Invertec has been optimized for stick (SMAW) and TIG (GTAW).
B-2 OPERA TION B-2 1 . POWER SWITCH - Place the lever in the “ON” position to energize the machine. When the power is on the output will be energized in STICK (SMAW) mode and TIG (GTAW) if the remote is set to local control. At power up the thermal Light and Fan will turn on for approxi- mately 3 seconds.
B-3 OPERA TION B-3 7. OUTPUT TERMINALS - These quick discon- nect terminals are compatible with TWECO®* con- nectors. The terminal provide connection points for the electrode and work cables. Refer to Output Connection in the Installation chapter for proper cable sizes.
B-4 OPERA TION B-4 OVERLOAD PROTECTION The machine is electrically protected from producing high output currents. Should the output current exceed 300A, an electronic protection circuit will reduce the current to less than 200A. The machine will continue to produce this low current until the pro- tection circuit is reset.
D-1 MAINTENANCE D-1 INPUT FIL TER CAP ACITOR DISCHARGE PROCEDURE 1 . Turn off input power or disconnect input power lines. 2. Remove the 5/16" hex head screws from the side and top of the machine and remove wrap-around machine cover.
D-2 MAINTENANCE D-2 ROUTINE MAINTENANCE 1. Perform the following preventive maintenance pro- cedures at least once every six months. It is good practice to keep a preventive maintenance record; a record tag attached to the machine works best.
ES 275i D-3 MAINTENANCE D-3 FIGURE D.2 — LOCATION OF MAINTENANCE COMPONENTS. SWITCH BOARD & HEA T SINK ASSEMBL Y CONTROL PC BOARD MAIN TRANSFORMER ASSEMBL Y CHOKE ASSEMBL Y OUTPUT TERMINALS POWE.
ES 275i E-1 TROUBLESHOOTING E-1 If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
ES 275i E-2 TROUBLESHOOTING & REP AIR E-2 _______________________________ CAUTION: Sometimes machine failures appear to be due to PC board failures. These problems can sometimes be traced to poor electrical connections. To avoid problems when troubleshooting and replacing PC boards, please use the following procedure: 1 .
ES 275i E-3 TROUBLESHOOTING E-3 Observe all Safety Guidelines detailed throughout this manual OUTPUT PROBLEMS PROBLEMS (SYMPTOMS) POSSIBLE CAUSE RECOMMENDED COURSE OF ACTION Major physical or electrical damage is observed when cover wrap-around is removed.
ES 275i E-4 TROUBLESHOOTING E-4 Observe all Safety Guidelines detailed throughout this manual OUTPUT PROBLEMS PROBLEMS (SYMPTOMS) POSSIBLE CAUSE RECOMMENDED COURSE OF ACTION Output turns on momentarily, then switches off and repeats cycle. Remote output control not functioning.
ES 275i E-5 TROUBLESHOOTING E-5 Observe all Safety Guidelines detailed throughout this manual OUTPUT PROBLEMS PROBLEMS (SYMPTOMS) POSSIBLE CAUSE RECOMMENDED COURSE OF ACTION No output - Main input fuses open, indicating excessive current draw. The machine operates normally when connected for 200 - 230VAC input.
ES 275i E-6 TROUBLESHOOTING E-6 Observe all Safety Guidelines detailed throughout this manual OUTPUT PROBLEMS PROBLEMS (SYMPTOMS) POSSIBLE CAUSE RECOMMENDED COURSE OF ACTION The machine will not produce more than 200 amps. 1. This may be normal operation.
ES 275i E-7 TROUBLESHOOTING E-7 Observe all Safety Guidelines detailed throughout this manual WELDING PROBLEMS PROBLEMS (SYMPTOMS) POSSIBLE CAUSE RECOMMENDED COURSE OF ACTION Poor welding, weld settings drift, or output power is low. Poor stick electrode welding performance.
F-1 WIRING DIAGRAMS F-1 ES 275i R2 AR C FOR CE WE LD MODE OFF 328 327 304 SMAW GTAW VIEW OF CONNECTOR ON PC BOARD ELECTRICAL SYMBOLS PER E1537. OHMS/WATTS COMPONENT VALUE UNITS: RESISTORS: MFD/VOLTS C.
F-2 WIRING DIAGRAMS F-2 ES 275i WIRING DIAGRAM- CODE: 1 1 166, 1 1223 R2 AR C FOR CE WE LD MODE OFF 328 327 304 SMAW GTAW VIEW OF CONNECTOR ON PC BOARD ELECTRICAL SYMBOLS PER E1537.
F-3 WIRING DIAGRAMS F-3 ES 275i WIRING DIAGRAM- CODES: 1 1266 R2 AR C FOR CE WE LD MODE OFF 328 327 304 SMAW GTAW VIEW OF CONNECTOR ON PC BOARD ELECTRICAL SYMBOLS PER E1537.
F-4 DIAGRAMS F-4 ES 275i L11981 A.02 9.00 11.85 20.25 3.17 MAX .79 MIN .88 .25 7.00 16.84 2.08 4.30 MAX RECONNECT DOOR OPEN 1.25 O .93 O 15.89 .35 TYP.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIP AMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
Een belangrijk punt na aankoop van elk apparaat Lincoln Electric IM803-B (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lincoln Electric IM803-B heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lincoln Electric IM803-B vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lincoln Electric IM803-B leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lincoln Electric IM803-B krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lincoln Electric IM803-B bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lincoln Electric IM803-B kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lincoln Electric IM803-B . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
