Gebruiksaanwijzing /service van het product LN-25 IM10092 van de fabrikant Lincoln Electric
Ga naar pagina of 39
OPERA T ORʼS MANUAL • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com • World's Leader in Welding and Cutting Products • Copyright © Lincoln Global Inc.
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC R A Y S can bur n. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
iii SAFETY iii FOR ELECTRIC ALL Y pow ered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A LʼArc 1.
v v SAFETY Electromagnetic Compatibility (EMC) Conformance Products displaying the CE mark are in conformity with European Community Council Directive of 15 Dec 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility, 2004/108/EC.
SAFETY vi vi Electromagnetic Compatibility (EMC) The size of the surrounding area to be considered will depend on the structure of the building and other activities that are taking place. The surrounding area may extend beyond the boundaries of the premises.
vii vii Thank Y ou for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
viii viii T ABLE OF CONTENTS Page –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Installation .
A-1 INST ALLA TION A-1 LN-25™ PIPE TEMPERA TURE RANGE OPERATION: -40°F to 104°F (-40°C to 40°C) STORAGE: -40°F to 185°F (-40°C to 85°C) INPUT VOL T AGE and CURRENT TECHNICAL SPECIFICA TIONS – LN-25™ PIPE (K2614-10) HEIGHT WIDTH DEPTH WEIGHT 14.
WELD CABLE SIZE Table A.1 located below are copper cable sizes rec- ommended for different currents and duty cycles. Lengths stipulated are the distance from the welder to work and back to the welder again. Cable sizes are increased for greater lengths primarily for the purpose of minimizing cable drop.
A-3 INST ALLA TION LN-25™ PIPE A-3 SHIELDING GAS CONNECTION CYLINDER may explode if damaged. • Keep cylinder upright and chained to support. • Keep cylinder away from areas where it may be damaged. • Never lift welder with cylinder attached. • Never allow welding electrode to touch cylinder.
A-4 INST ALLA TION LN-25™ PIPE A-4 WIRE DRIVE CONFIGURA TION (See Figure A.2) CHANGING THE GUN RECEIVER BUSHING ELECTRIC SHOCK can kill. • Turn the input power OFF at the welding power source before instal- lation or changing drive rolls and/or guides.
THUMB SCREW GUN A-5 INST ALLA TION LN-25™ PIPE A-5 PRESSURE ARM ADJUSTMENT ELECTRIC SHOCK can kill. • Turn the input power OFF at the weld- ing power source before installation or changing drive rolls and/or guides. • Do not touch electrically live parts.
CV Power Sources with Stud Connectors and no Remote/Local Switch. (See Figure A.7) Place CV/CC switch in the feeder in the "CV" position. Work clip Work Electrode Jumper Ranger 250, 250 LPG Ranger 305G, 305D Ranger 10,000 Ranger 3 Phase Ranger 225GXT Ranger 225 Commander 300 V antage 300, 400, 500 Air V antage 500 LN-25™ PIPE FIGURE A.
A-7 INST ALLA TION LN-25™ PIPE A-7 CV Power Source with Twist-Mate Connectors and Remote/Local Switch. (See Figure A.8) Place CV/CC switch in the feeder in the "CV" position. Work clip Wor k Electrode CV -305 V350-Pro LN-25™ PIPE FIGURE A.
A-8 INST ALLA TION LN-25™ PIPE A-8 ELECTRODE CONNECTION The LN-25™ PIPE (CCC) does not include the elec- trode cable. The customer is to install an AWG 2/0 to 4/0 cable. To install: 1. Turn off power at the welding power source. 2. With a 5/16” nut driver, remove the 4 screws hold- ing the rear cover panel.
B-1 OPERA TION LN-25™ PIPE B-1 • ELECTRIC SHOCK CAN KILL. Unless using COLD FEED fea- ture, when feeding with gun trig- ger, the electrode and drive mechanism are always electri- cally energized and could remain energized several sec- onds after the welding ceases.
B-2 OPERA TION B-2 LN-25™ PIPE DEFINITION OF WELDING TERMS WFS • Wire Feed Speed CC • Constant Current CV • Constant Voltage GMAW • Gas Metal Arc welding SMAW • Shielded Metal Arc welding .
WIRE FEED SPEED KNOB Wire Feed Speed, CV Operation When Across the Arc models are operated with CV power sources, the wire feed speed will remain a con- stant value, independent of arc voltage changes, as along as the arc voltage does not drop below the val- ues per the following table.
B-4 OPERA TION B-4 LN-25™ PIPE POWER-UP SEQUENCE All of the LEDʼs will briefly illuminate during power-up. If the gun trigger is activated during power up, the feeder will not operate until the gun trigger is released. WIRE FEED SPEED/AMPERAGE DISPLA Y Idle The left display shows the preset wire feed speed .
B-5 OPERA TION B-5 LN-25™ PIPE WIRE FEED SPEED UNITS To change the wire feed speed units: Rotate the WFS knob to the left to use “inches/minute” for the wire feed speed units. Rotate the WFS knob to the right to use “meters/minute” for the wire feed speed units.
B-6 OPERA TION B-6 LEFT DISPLA Y SELECTION The left display can show either amperage or actual WFS during welding. Note that actual WFS is not the same as preset WFS.
B-7 OPERA TION B-7 INTERNAL CONTROLS LN-25™ PIPE 12 Step Trigger Interlock Switch 2 Pressure Adjustment Arm 3 Optional Timer Kit (See Accessories Section) 4 Spool Retainer 5 Spindle Brake 6 Gun Bush.
B-8 OPERA TION B-8 INTERNAL CONTROLS DESCRIPTION (See Figure B.2) 2 Step - Trigger Interlock Switch The 2 Step - Trigger Interlock switch changes the function of the gun trigger. 2 Step trigger opera- tion turns welding on and off in direct response to the trigger.
GAS PURGE PUSHBUTTON The gas solenoid valve will energize but neither the power source output nor the drive motor will be turned on. The Gas Purge switch is useful for setting the proper flow rate of shielding gas. Flow meters should always be adjusted while the shielding gas is flowing.
C-1 ACCESSORIES C-1 LN-25™ PIPE F ACTOR Y INST ALLED EQUIPMENT • K1500-2 Gun Receiver Bushing. DRIVE ROLL KITS (See Parts Pages) K1803-1 K1840-xx K1842-xx Work and Feeder Cables Package. Weld Power Cable, Twist-Mate to Lug. Weld Power Cable, Lug to Lug.
C-2 ACCESSORIES C-2 LN-25™ PIPE K910-1 K910-2 K1500-1 K1500-2 K1500-3 Ground Clamp Ground Clamp Gun Receiver Bushing (for guns with K466-1 Lincoln gun connec- tors; Innershield and Subarc guns) Gun .
C-3 ACCESSORIES C-3 LN-25™ PIPE K1500-4 K1500-5 K435 K468 K590-6 K586-1 K283 Gun Receiver Bushing (for gun with K466-3 Lincoln gun connec- tors; compatible with Miller® guns.) Gun Receiver Bushing (compatible with Oxo® guns.) Spindle Adapter, for mounting 14 lb.
ELECTRIC SHOCK can kill. • Turn the input power OFF at the welding power source before installation or changing drive rolls and/or guides. • Do not touch electrically live parts.
E-1 TROUBLESHOOTING E-1 LN-25™ PIPE If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-2 TROUBLESHOOTING E-2 LN-25™ PIPE Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-3 TROUBLESHOOTING E-3 LN-25™ PIPE Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-4 TROUBLESHOOTING E-4 LN-25™ PIPE Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
F-1 DIAGRAMS F-1 LN-25™ PIPE NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement.
F-2 DIMENSION PRINT F-2 LN-25™ PIPE.
W ARNING A VISO DE PREC A UCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF A CTURER’S INSTR UCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLL O W Y OUR EMPL O YER’S SAFETY PRA CTICES.
W ARNING A VISO DE PREC A UCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREEND A A S INSTR UÇÕES DO F ABRIC ANTE P ARA ES TE EQUIP AMENT O E AS P ARTES DE USO , E SIG A AS PRÁTIC A S DE SEGUR ANÇA DO EMPREG ADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
Een belangrijk punt na aankoop van elk apparaat Lincoln Electric LN-25 IM10092 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lincoln Electric LN-25 IM10092 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lincoln Electric LN-25 IM10092 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lincoln Electric LN-25 IM10092 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lincoln Electric LN-25 IM10092 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lincoln Electric LN-25 IM10092 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lincoln Electric LN-25 IM10092 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lincoln Electric LN-25 IM10092 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
