Gebruiksaanwijzing /service van het product TANDEM IM666-A van de fabrikant Lincoln Electric
Ga naar pagina of 25
T andem MIG T orch OPERA TOR’S MANUAL IM666-A February, 2005 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thought- ful operation on your part.
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv Mar. ‘93 PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
v v Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
vi vi T ABLE OF CONTENTS Page Installation ................................................................................................................... ....Section A Technical Specifications .....................................................
A-1 INST ALLA TION TANDEM MIG TORCH A-1 TECHNICAL SPECIFICA TIONS - T andem MIG T orch Product Number G3494-2, 2A G3494-3, 3A G3494-4, 4A G3494-5, 5A G3494-6, 6A Gun Cable Length 4 ft (1.2 m) 6 ft (1.8 m) 8 ft (2.4 m) 10 ft (3.0 m) 12 ft (3.6m) 65 scfh (31 liters/min) minimum .
A-2 INST ALLA TION TANDEM MIG TORCH A-2 GENERAL DESCRIPTION The Tandem MIG torch delivers two wire electrodes to the weld pool. The wires are insulated from each other for the purpose of independent arc regulation. When welding, the wires or arcs are oriented one behind the other.
A-3 INST ALLA TION TANDEM MIG TORCH A-3 CABLE ASSEMBL Y Three cable assemblies deliver the necessary power and cooling fluids to the torch. a) G3494-X Series: Two of the cable assemblies supply power, wire and water cooling to each side of the torch.
A-4 INST ALLA TION TANDEM MIG TORCH A-4 LINER INST ALLA TION AND TRIMMING INSTRUCTIONS a ) Lay the torch and cable on a flat surface and straighten the cables. b) With a 12 mm open-end wrench, unscrew the nut on the cable connector that restrains the liner.
A-5 INST ALLA TION TANDEM MIG TORCH A-5 b) Push the end connector from torch into K489-7 Fast-Mate adapter on the wire feeder, and then tighten the locking nut. Do this for both of the torch power cables. c) Attach the water lines from the torch power cables to a supply of cooling water.
A-6 INST ALLA TION TANDEM MIG TORCH A-6 MOUNTING THE T ORCH Always insulate the torch from any equipment or fixturing. Use M19190 Bracket Arm to Torch Body Insulator if necessary. (See Figure 4, Torch mounting dimensions) Check to make sure the cables are free to flex and do not get tangled or caught on other equipment.
WIRE STRAIGHTENERS Use a wire straightener with each wire drive. Failure to use a wire straightener may result in inconsis- tent welds and weld bead placement. T AIL GAS COVERAGE The Tandem Mig process is capable of establishing wide weld bead profiles at higher than usual travel speeds.
B-1 OPERA TION TANDEM MIG TORCH B-1 ELECTRODES AND EQUIPMENT TheTandem MIG torch has been designed for use with 0.035" through 5/64" (0.9 mm to 1.9 mm) Lincoln solid steel MIG wires and metal core wires. Refer to the appropriate Lincoln Process and Procedure Guidelines for further information on welding settings.
C-1 ACCESSORIES C-1 GENERAL OPTIONS / ACCESSORIES The following options/accessories are available for your Tandem MIG Torch from your local Lincoln Distributor. K489-7 Connector Kit - Magnum Fast-Mate Adapter Liners Steel, Stainless and Metal Cored Electrodes S24198-10 .
D-1 MAINTENANCE D-1 T ORCH SHIELD REPLACEMENT It is important that the torch shield be inspected and replaced on a routine basis. The torch shields (S24432, -1, -A, -1A) are designed to protect the more expensive overmolded assembly of the Tandem torch from arc and heat induced erosion.
D-2 MAINTENANCE D-2 CONT ACT TIP REPLACEMENT Each application will dictate the frequency of contact tip replacement. Higher amperage higher duty cycle operations will require more frequent contact tip replacement. The condition of the contact tip greatly effects the welding performance.
E-1 TROUBLESHOOTING E-1 TANDEM MIG TORCH If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-2 TROUBLESHOOTING E-2 TANDEM MIG TORCH Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-3 TROUBLESHOOTING E-3 TANDEM MIG TORCH Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
NOTES TANDEM MIG TORCH.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE PARA ESTE EQUIP AMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
Een belangrijk punt na aankoop van elk apparaat Lincoln Electric TANDEM IM666-A (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lincoln Electric TANDEM IM666-A heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lincoln Electric TANDEM IM666-A vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lincoln Electric TANDEM IM666-A leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lincoln Electric TANDEM IM666-A krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lincoln Electric TANDEM IM666-A bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lincoln Electric TANDEM IM666-A kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lincoln Electric TANDEM IM666-A . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
