Gebruiksaanwijzing /service van het product WPS11 van de fabrikant Linksys
Ga naar pagina of 31
Instant Wireless ™ Series Wireless PrintSer v e r Use this guide to install: Model No.: WPS11 ver . 3 User Guide.
COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. Instant Wireless is a trademark of Linksys. Microsoft, Windows, and the Windows logo ar e register ed trademarks of Microsoft Corporation. All other trademarks and brand names ar e the property of their respective pr oprietors.
T able of Contents Chapter 1: Introduction 1 The Instant W ireless PrintServer 1 F eatures 1 Package Contents 2 Chapter 2: Getting to Know the Wireless PrintServer 3 The W ireless PrintSer ver’ s LE.
• One Instant W ireless™ PrintSer ver • One Antenna using Rev erse SMA Connector • One Setup Utility CD-R OM with User Guide • One P ow er Adapter • One Quick Install and One Registration .
4 LAN This port connects to your wired netw ork using a standard Category 5 (or better) Ethernet cable. Printer This Parallel (LPT) P ort connects to your printer . Reset Button Press this button to reset the PrintServer to factor y defaults and generate a diagnostic printout, which is discussed belo w .
6 Connecting a Printer to the Wireless PrintServer 1. Connect your printer to the W ireless PrintSer ver’ s Printer (LPT) port with your printer cable. Some printers, especiall y bi-direc- tional models, ma y require special shielded cabling. Consult y our printer’ s user guide for cabling specif ications.
Wireless PrintServer 1. Inser t the Setup Utility CD . A built-in autor un will begin the installation of the PrintServer’ s Bi-Admin Management Utility , and display F igure 4-1. Click the product you wish to install, follo w ed by the Install tab to continue.
1. T o begin dri ver installation, click the Start button, select Run , and type D:Driv erWin9xntsetup.ex e (where “D” is the letter of your CD-R OM driv e) in the Open f ield that appears. Click the OK button. 2. The W elcome screen appears. Read the text that appears and click the Ne xt button.
Wireless PrintServer 12 5. Dri ver installation is no w completed but the Print Driv er still needs to be conf igured. Check the bo x beside Conf igur e Print Driv er No w and click the Finish button to continue. 6. Double-click the Print Driver Setup shortcut icon .
Wireless PrintServer 14 10. This will display the Conf igure Printer P ort screen. Any installed printers will be displa yed in the Existing Printers f ield. Y ou can install a printer b y clicking the Add Ne w Printer button. 11. The Add Printer W izard screen will come up at this point.
16 Chapter 5: Bi-Admin: PrintSer ver Management The W ireless PrintSer ver is managed b y a utility program called Bi-Admin on the W ireless PrintSer ver’ s Setup CD .
18 Obtaining Device Information: The Device Information Icon T o access infor mation about the W ireless PrintSer ver , either click on it in the Device List windo w (on the right side of the Bi-Admin windo w) or highlight the W ireless PrintServer and click on the Device Inf ormation icon, sho wn in Figure 5-2.
20 Logical P ort Configuration: Logical P ort Configuration Icon T o set or change the W ireless PrintServer’ s logical port set- tings, highlight the W ireless PrintSer ver to be changed and click on the Logical P ort icon (sho wn in Figure 5-7). The Logical P ort Conf iguration windo w will appear .
T o disable one of the W ireless PrintServer’ s protocols, click once on the Device Name of the W ireless PrintSer ver you w ant to change, and click Conf iguration , follo wed b y System . The System Conf iguration window will appear . Each protocol is listed , along with Enab le and Disab le buttons.
When the Conf igure Serv er screen appears, enter the W ireless PrintServer name (SC0222CC is the example sho wn in Figure 6-3) . Then enter your pass word (if y ou created one) into the Device P assw ord f ield and type it again in the V erify Pass w ord f ield to conf irm it.
Click the Wir eless tab to allo w you to change information about the W ireless PrintServer . Y ou can conf igure the SSID , Channel Number , and Netw ork T ype. Y ou can also tur n on or off the WEP data encr yption feature, as w ell as choose either 64-bit or 128-bit data encryption.
Chapter 7: Advanced Proper ties The Adv anced Properties section of the W eb-based Utility is for users who ha ve a thorough understanding of netw orks and network settings. Changing these settings can cause inter ruption of network communication and mak e the W ireless PrintSer ver cease to function properl y .
Click the Logical Printers ta b to vie w or change the lo gical printer settings of the W ireless PrintSer ver . F or each Logical Printer , the follo wing f ields are av ailable: Logical Printer (P ort) - Select the Logical Printer P ort you wish to conf igure.
Click the SNMP tab to vie w or change the SNMP settings of the W ireless PrintServer . The W ireless PrintSer ver supports SNMP (Simple Network Management Protocol). This allo ws netw ork super visors to monitor and control the W ireless PrintSer ver using netw ork management platfor ms such as HP OpenV iew , IBM SystemVie w , etc.
Chapter 8: Internet Printing Protocol (IPP) IPP (Internet Printing Protocol) is a new standards-based system to allo w remote printing from a PC to an y accessible printer . Nor mally , the printer will be attached to a computer or other device that functions as an IPP Server .
4. Click Sa ve to create the IPP port on your system. Y ou will see a message conf irming that the por t has been created , then Figure 8-2: 5. Either select an existing printer to use the ne w por t, and click OK . OR Click the Add Ne w Printer button to create a new printer to use the IPP port.
2. Select Network Printer and click Next to see the Locate y our Printer screen, as sho wn in Figure 8-4. 3. Select Connect to a printer on the Internet or on your intr anet , and enter the URL of the IPP Server as follo ws, where ip_address represents the IP Address of the IPP Server , and 631 is the por t number .
40 Chapter 9: DHCP Suppor t for the Wireless PrintSer v e r T o use DHCP , w hich assigns non-static IP addresses, you must ha ve a DHCP server and DHCP management software. Otherwise, the W ireless PrintServer’ s IP address will remain unkno wn, and connecting to it will be impossible.
Appendix B: About Bi-Directional Printing Normal printing only sends print signals from a PC to a printer . Bi-dir ection- al printing , also called bitronic printing, refers to a printer's ability to do just the opposite—talk back to a PC to notify it of a print job status, paper jams, etc.
your printer came with special bi-directional softw are allo wing you to monitor printer status, do not use it with the W ireless PrintServer—the software is most likel y not network-capab le.
Ethernet - IEEE standard netw ork protocol that specif ies ho w data is placed on and retriev ed from a common transmission medium. Has a transfer rate of 10 Mbps. F or ms the underlying transport vehicle used b y sev eral upper-le vel protocols, including TCP/IP and XNS.
NetBIOS - The native netw orking protocol in DOS and W indows netw orks. Although originall y combined with its transport lay er protocol (NetBEUI), NetBIOS toda y provides a pro g ramming interface for applications at the ses- sion la yer (la yer 5).
TCP/IP - T ransmission Control Protocol/Internet Protocol (TCP/IP) is the basic communication language or protocol of the Internet. It can also be used as a communications protocol in a priv ate netw ork (either an intranet or an extranet).
Appendix F: Environmental Dimensions: 4.76" x 3.74" x 1.18" (121 mm x 95 mm x 30 mm) Unit Weight: 5.6 oz. (0.16 kg) P ower: External, 12V DC, 800 mA Certifications: FCC Class B , CE Mark Operating T emp.: 0ºC to 40ºC (32ºF to 104ºF) Storage T emp.
54 Appendix H: Contact Information F or help with the installation or operation of this product, contact Linksys T echnical Suppor t at one of the phone numbers or Inter net addresses belo w . Sales Information 800-546-5797 (LINKSYS) T echnical Suppor t 866-242-8558 RMA Issues 949-271-5461 Fa x 949-265-6655 Email support@linksys.
© Copyright 2002 Linksys, All Rights Reserved. http://www .linksys.com.
Een belangrijk punt na aankoop van elk apparaat Linksys WPS11 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Linksys WPS11 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Linksys WPS11 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Linksys WPS11 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Linksys WPS11 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Linksys WPS11 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Linksys WPS11 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Linksys WPS11 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
