Gebruiksaanwijzing /service van het product 1100 van de fabrikant Makita
Ga naar pagina of 16
Power Planer Planing width 82 mm (344”) MODEL 1100 Planing Rabbeting No load speed Overall Net depth depth (RPM) length weight INSTRUCTION MANUAL 82 mm (3-114”) DOUBLE INSULATION 415 mm 4.9 kg (1 6-318”) (10.8 Ibs) 16,000 3 mm 20 mm (118“) (314”) SPECIFICATIONS Manufacturer reserves the right to change specifications without notice.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.
ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work 2. Avoid cutting nails. Inspect for and remove all nails from the workpiece before 3. Handle the blades very carefully. 4. Be sure the blade installation bolts are securely tightened before operation.
Removing or installing mini planer blades CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blades on the drum, un- screw the three installation bolts with the socket wrench. The drum cover comes off together with the blades.
7. The blade's lengthwise adjustment will need to be manually positioned so that the blade ends are clear and equidistant from the housing on one side and the metal bracket on the other.
For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the rear base.
Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in Lock button - the lock button. To stop the tool from the locked position, pull the trigger fully, then release it.
Shiplapping To make a stepped cut as shown at the right, use the edge fence. Draw a cutting line on the workpiece. In- sert the edge fence into the hole in the front of the tool. Align the blade edge with the cutting line. Adjust the edge fence until it comes in con- tact with the side of the workpiece, then secure it by tightening the screw.
Chamfering To make a cut as shown at the right, align the "V" groove in the front base with the edge of the workpiece and plane it as shown in the figure (A). Sharpening planer blades Always keep your blades sharp for the best performance possible.
Immerse the dressing stone in water for 2 or 3 minutes before sharpening. Hold the holder so that the blades both contact the dressing stone for simultaneous sharpening at the same angle.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark.
ACCESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
May-l5-'90 US 82 mm (3-1/4') POWER PLANER Model 1100 Note: The switch, noise suppressor and other part configurations may differ from country to country.
MODEL 1100 ITEM NO. NO. USED MACHINE __ MACHlNE 33 34 35 36 37 38 39 40 41 42 43 44 45 46 41 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Mav-15-'90 US DESCRIPTION 'Yz G2D DESCRIPTION .
f MAKITA LlMrED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Een belangrijk punt na aankoop van elk apparaat Makita 1100 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita 1100 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita 1100 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita 1100 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita 1100 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita 1100 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita 1100 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita 1100 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
