Gebruiksaanwijzing /service van het product 8411DW van de fabrikant Makita
Ga naar pagina of 16
Cordless Hammer Drill Capacities Steel Wood Wood screw Concrete 10 mm (3/8”) 21 mm I13/16”) 71;4m: ~~~~1~~ 10 mm (3/8”) Equipped with electric brake MODEL 8411D MODEL 8411DW With Fast Charger No load speed (RPM) High LOW 0 ~ 1,150 0 -- 370 INSTRUCTION MANUAL 0 ~ 12,700 1.
I M PO RTANT SAFETY I N STRUCTI 0 N S (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.
IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord I. SAVE THESE INSTRUCTIONS - This manual 25 50 100 150 18 18 18 16 9. Do not operate charger with damaged cord or plug - replace them im- mediately.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents.
Installing or removing battery cartridge .Always switch off the tool before insertion or removal of the battery cartridge. .To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool.
Installing or removing drill bit or driver bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit.
Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop.
Operation 1) Hammer drilling operation : When drilling in concrete, granite, tile, etc., turn the knob so that the a mark on the knob points to the mark. Be sure to use a tungsten-carbide tipped bit. To position a hole accurately, start the tool slowly and then increase the speed gradually.
0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw, The guide screw makes drilling easier by pulling the bit into the workpiece. To prevent the bit from slipping when starting a hole, make an indentation with a center- punch and hammer at the point to be drilled.
Dust cover Use the dust cover to prevent dust and dirt from falling over the tool, yourself and on floor when performing overhead drilling operations. Install the dust cover on the tool’s collar as shown in the figures below. When installing it, push the dust cover firmly enough to be completely installed on the tool’s collar.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Apr.-l4-'92 EN CORDLESS HAMMER DRILL Model 8411D Note: The switch and other part configurations may differ from country to country. 14.
Apr-l4--'92 EN MODEL 8411D ';iM DESCRIPTION 'LiM A& DESCRIPTION MACHINE ~ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 1 1 1 1 1 1 1 1 1 1 1 1 I 1 1 8 .
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Een belangrijk punt na aankoop van elk apparaat Makita 8411DW (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita 8411DW heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita 8411DW vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita 8411DW leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita 8411DW krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita 8411DW bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita 8411DW kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita 8411DW . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
