Gebruiksaanwijzing /service van het product BHR243 (LXRH02*1) van de fabrikant Makita
Ga naar pagina of 25
Models No. Description PRODUCT T ECHNICAL INFORMA TION C ONCEPT AND MAIN APPLICA TIONS S pecification S tandard equipment O ptional accessories P 1/ 25 BHR242 (LXRH01* 1 ), BHR243 (LXRH02* 1 ) Cordles.
[1] NECESSARY REPAIRING TOOLS Description Code No. Use for Retaining ring pliers ST-2N 1R003 remo v ing Ri ng spr i ng 19 fro m To ol ho l de r co mp lete/ To ol hol der gu i de complet e Retaining ring pliers ST-2 1R004 assembling Cam shaft Bearing setting plate 15.
[2] LUBRICATION Apply the following grease to protect parts and product from unusual abrasion. Fig. 1 I tem No . Description Portion to lubricate Lubricant See Fig. 3. A m oun t 3g a little a little a little 3g Compression spring 14 End to be fixed to the boss in Inner housing complete (See Fig.
Put 16g Makita grease RB No 00 by using the space (designated by the black dot) to lubricate Swash bearing section and Cam shaft section. boss for fixing Compression spring 14 Inside view of Inner housing Fig.
[3] DISASSEMBLY/ASSEMBLY [3] -1A. Bit holder section for BHR242 DISASSEMBLING for BHR242 R epair P 5 / 25 Chuck cover Chuck cover Chuck cover Cap 35 Groove of Tool holder complete Tool holder complete (1) Remove Cap 35. (2) Separate Ring spring 14 from the groove of Tool holder complete using 1R003 with 1R212.
[3] DISASSEMBLY/ASSEMBLY [3] -1B. Holder section for BHR243 DISASSEMBLING R epair P 6 / 25 (1) Remove Tool holder set from Tool holder guide complete. ( Fig. 8 ) (2) Remove Cap 35, then separate Ring spring 19 from the groove of Tool holder using 1R003 with 1R212.
P 7 / 25 [3] DISASSEMBLY/ASSEMBLY [3]-1B. Holder section for BHR243 (cont.) ASSEMBLING R epair (1) Assemble Torsion spring 31 to Tool holder as follows: • Set two Steel balls 6 on the holes of Tool holder. • Insert the short arm of Torsion spring 31 into the hole of Tool holder.
P 8 / 25 [3] DISASSEMBLY/ASSEMBLY [3]-2. Drill chuck assembly for BHR243 R epair DISASSEMBLING Fig. 18 Fig. 19 Fig. 22 Fig. 21 Fig. 20 Steel ball 5.0 Leaf spring Flat washer 24 Drill chuck assembly can be disassembled as drawn in Figs.
Change cover Change ring ASSEMBLING Chuck holder short arm of Torsion spring 31 long arm of Torsion spring 31 hole for Torsion spring 31 (1) Holding the flat portions of Chuck holder in vise, assemble Drill chuck to Chuck holder by turning it clockwise using Hex wrench 10.
[3] DISASSEMBLY/ASSEMBLY [3]-3. Change lever (1) Remove dust and dirt from Change lever and the grooved area on Motor housing. (2) Set Change lever to Hammer mode.
[3] DISASSEMBLY/ASSEMBLY [3]-4. Rotor (1) Loosen four 4x35 Tapping screws, and then remove Battery housing R and Housing R in order from their housings L. ( Fig. 31 ) (2) Remove Gear housing section as drawn in Fig. 32 . Inner housing in Gear housing section comes with Rotor.
Fig. 35 [3] DISASSEMBLY/ASSEMBLY [3]-5. Torsion spring 6 for Connector, Battery housing ASSEMBLING R epair P 1 2 / 25 A B C Cushion rubber (R) Cushion rubber (L) (behind Terminal) Rubber pin 5 Pin 1.5 See Fig. 35 . Set Torsion spring 6 into Housing L, and then assemble Connector to Compression spring 6.
[3] DISASSEMBLY/ASSEMBLY [3]-6. Torque limiter section DISASSEMBLING ASSEMBLING R epair P 1 3 / 25 (1) Disassemble T ool holder section. ( Fi gs . 4 to 6 for BHR242/ Figs.
[3] DISASSEMBLY/ASSEMBLY [3]-6. Impact bolt in Torque limiter section R epair P 14 / 25 DISASSEMBLING (1) Put 1R388 into Tool holder (guide) complete, then push 1R388 in vise with the access holes on Tool holder (guide) complete parallel to Vise. ( Fig.
[3] DISASSEMBLY/ASSEMBLY [3]-6. Impact bolt in Torque limiter section (cont.) R epair P 15 / 25 ASSEMBLING Note: 2 Fig. 44A Fig. 44B Impact bolt A (1) Assemble Impact bolt section to Tool holder (guide) complete as drawn in Fig.
P 16 / 25 R epair DISASSEMBLING Fig. 47 Fig. 49 Fig. 48 Fig. 50 Fig. 51 (1) Disassemble Motor housing section, Gear housing section and Inner housing section. (2) Remove Flat fillister HD pin 6, two Weight holder guides, Flat washer 6, Stop ring E-5, Inner support complete and two M4x25 Hex socket head bolts from Inner housing.
P 17 / 25 R epair DISASSEMBLING ASSEMBLING Fig. 52 Fig. 53 (6) Remove Stop ring EXT U-6 from Can shaft, then separate Flat washer 7, Spur gear 10 and Clutch cam A from Can shaft. (7) Receive Spiral bevel gear 32 on 1R139 put on U-groove of Arbor press table and press out Cam shaft with 1R281 (ø7mm round bar) as drawn in Fig.
P 18 / 25 R epair ASSEMBLING Fig. 55 (5) Set Compression spring 14 and Flat washer 14 to the projection of Inner housing as drawn in Fig. 55 . Insert Guide plate and Piston joint into Piston cylinder, and then pass the pole of Swash bearing 10 through Piston joint.
1R258 P 19 / 25 R epair [3] DISASSEMBLY/ASSEMBLY [3]-8. Oil seal 25, Cup sleeve, Ball bearing 6806LLU Fig. 60 Ball bearing 6806LLU Cup sleeve Fig. 61 Fig.
P 2 0 / 25 R epair [3] DISASSEMBLY/ASSEMBLY [3]-9. Motor of Dust extraction system DX01, DX02 Fig. 65 Fig. 66 Note: Special repairing tool and Lubricant are not required. (1) Separate Housing R and eight 4x18 Tapping screws from Housing L. (2) Remove Baffle plate, Filter plate, Sponge sheet C and Motor complete as an assembled part.
P 2 1 / 25 R epair [3] DISASSEMBLY/ASSEMBLY [3]-10. Slide levers of Dust extraction system DX01, DX02 Fig. 67 Fig. 68 • Slide lever B on Housing L Remove Rack B and Compression spring 3 in Housing L as drawn in Fig. 67 , and then move Slide lever B toward the upper direction like the arrow mark.
P 2 2 / 25 R epair [3] DISASSEMBLY/ASSEMBLY [3]-11. Tips on repair of Dust extraction system DX01, DX02 Fig. 69 Fig. 70 • Hose 30 is not glued on the other parts, and therefore it is possible to remove Hose 30 from Collector base A (DX01)/ B (DX02) and Inner pipe.
P 2 3 / 25 C ircuit diagram Fig. D-1 Fig. D-2 Terminal Switch BHR242, BHR243 DX01, DX02 Stator Controller Orange mark White mark Black mark Connector to Dust extraction system (DX01, DX02) Connector t.
P 24 / 25 BHR242, BHR243 Lead wires to Connector have to be routed between Rib B and Rib D. Lead wires to Connector and Stator lead wires have to be routed between Rib A and Rib B. Route the lead wires between Connector and Controller to the bottom of Housing L so as not to rise on the top line of Rib C.
P 25 / 25 W iring diagram (cont.) Fig. D-4 DX01, DX02 Red mark Black lead wire Connector viewed from lead wire installation side Lead wires between Connector and Controller have to fixed with these lead wire holders. Do not slack them between the lead wire holders.
Een belangrijk punt na aankoop van elk apparaat Makita BHR243 (LXRH02*1) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita BHR243 (LXRH02*1) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita BHR243 (LXRH02*1) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita BHR243 (LXRH02*1) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita BHR243 (LXRH02*1) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita BHR243 (LXRH02*1) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita BHR243 (LXRH02*1) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita BHR243 (LXRH02*1) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
