Gebruiksaanwijzing /service van het product HR2511 van de fabrikant Makita
Ga naar pagina of 16
Rotary Hammer Capacities Wood Steel Concrete 30" 13 mm 25 mm (1-311 6") (112") (1") 25 mm (1") MODEL HR2511 Variable Speed Net weight 335 mm 4.2 kg ~~ows per min. Overs" (RPM) length No load speed ~ 3,000 (13-3116") (9.
IMPORTANT SAFETY I NSTRU CTI 0 NS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool.
ADDITIONAL SAFETY RULES 1. Wear a hard hat (safety helmet), safety glasses and/or face shield. It is also highly recommended that you wear a dust mask, ear protectors and thickly padded gloves. 2. Be sure the bit is secured in place before operation. 3.
Bit grease Coat the bit shank head beforehand with a small amount (about 0.5- 1 g; 0.02-0.04 oz.) of bit grease. This chuck lubrication assures smooth action and longer service life. Installing or removing drill bit CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the bit.
Side grip (auxiliary handle) The side grip swings around to either side, allowing easy handling of the tool in any position. Loosen the side grip by turning it counterclockwise, swing it to the desired position and then tighten it by turning clockwise.
Switch action Too speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. A speed control screw is provided so that maximum tool speed can be limited (vari- able). Turn the speed control screw clock- wise for higher speed, and counterclock- wise for lower speed.
Driving in anchor manually The drill bit has a red marking at a point corresponding to the anchor length. So drill to that depth. Use the blow-out bulb to clean out the hole. Put a plug on the anchor and hammer it into the concrete. setting tool hor setting rod) Screw in a bolt to fasten equipment.
Dust collector Use the dust collector for safe, sanitary overhead operations. Install the bit, then attach the dust collector on the end by turning and applying pressure. Then secure it by turning the metal retainer clockwise. CAUTION : Empty the dust collector of its contents after drilling every 2 or 3 holes.
Install the center bit. I Center bit Rest the core bit on the concrete and turn the tool on. Once the core bit has cut a shallow groove into the concrete, remove the center bit. Then resume drilling. To remove the core bit, hold the adapter with the wrench, insert the rod into the hole in the core bit and tap with a hammer to unscrew.
MA1 NTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor.
Lubrication This tool requires no hourly or daily lubrication because it has a grease-packed lubrication system. It should be relubricated after every 6 months of operation. Send the complete tool to Makita Authorized or Factory Service Center for this lubrication service.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
oct -08-'91 us 25 mm (1") ROTARY HAMMER Model HR2511 Note: The switch and other part configurations may differ from country to country. 15.
oct -08-'91 us MODEL HR2511 'LiM AtD DESCRIPTION 'LiM ,& DESCRIPTION MACHINE *E 2 4 Hex Socket Head Bolt M6x25 lWtth Washer1 4 1 Ball Bearing 3009 5 2 Roller 6 5 6 1 Nut M303-36 7 1.
Een belangrijk punt na aankoop van elk apparaat Makita HR2511 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita HR2511 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita HR2511 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita HR2511 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita HR2511 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita HR2511 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita HR2511 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita HR2511 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
