Gebruiksaanwijzing /service van het product HR4500C van de fabrikant Makita
Ga naar pagina of 16
Rotarv Hammer Capacities Tungsten-carbide bit 1 Core bit I 45 mm (1-3/4") MODEL HR4500C No load speed Blows Overall Net IRPMI per minute 1 length I weight INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS * Manufacturer reserves the right to change specifications without notice.
GENERAL SAFETY RULES USA0021 (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit.
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
USBOlO 1 Specific Safety Rules 1. Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
SYMBOLS The followings show the symbols used for tool. V A Hz % n, El .. ./min LI=, ................................. volts ................................. amperes ................................. herts ................................. alternating current .
FUNCTIONAL DESCRIPTION Selecting action mode Rotation with hammering For drilling in concrete, masonry, etc., depress the lock button and rotate the change lever so that the pointer points to the symbol. Use a tungsten carbide- tipped bit. The bit can be secured at 16 different angles.
Depress the lock button and rotate the change lever so that the pointer points to the symbol. Then make sure that the bit is securely held in place by turning it slight- ly. Side handle CAUTION: Use the side handle only when chipping, scaling or demolishing.
Switch action CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released.
indicator lamp The green power-ON indicator lamp lights up when the tool is switched ON. If the indi- cator lamp is lit but the tool does not start, the carbon brushes may be worn out, or the electric circuit or the motor may be defective.
If the bit cannot be pushed in, remove the bit. Pull the chuck cover down a couple of times. Then insert the bit again. Turn the bit and push it in until it engages. After installing, always make sure that the bit is securely held in place by trying to pull it out.
OPERATION Hammer drilling operation Set the change lever to theufl symbol. Position the bit at the location for the hole, then pull the trigger. Do not force the tool. Light pressure gives best results. Keep the tool in position and prevent it from slipping away from the hole.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the car- bon brush is exposed to contact the com- mutator, it will automatically shut off the motor.
Lubrication CAUTION: This servicing should be performed by Makita Authorized or Factory Service Centers only. This tool required no hourly or daily lubrica- tion because it has a grease-packed lubri- cation system. It should be relubricated after every 6 months of operation.
Rest the tool on the table with the bit end pointing upwards. This will allow the old grease to collect inside the crank housing. Wipe out the old grease inside and replace with a fresh grease (60 9). Use only Makita genuine hammer grease (optional accessory).
ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Safety goggle Part No.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm.
Een belangrijk punt na aankoop van elk apparaat Makita HR4500C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita HR4500C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita HR4500C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita HR4500C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita HR4500C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita HR4500C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita HR4500C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita HR4500C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
