Gebruiksaanwijzing /service van het product HRH01 van de fabrikant Makita
Ga naar pagina of 22
Capacity: mm (") HR262D/ BHR262 (HRH01C/ HRH01) *1 HR262TD/ BHR262T (HRH02C/ HRH02) *1 Yes Yes Yes (by trigger) 13 (1/2) 32 (1-1/4) 26 (1) 4.5 (9.9) Models No. Description C ONCEPT AND MAIN APPLICATIONS S pecification S tandard equipment O ptional accessories Note: The standard equipment for the tool shown above may vary by country.
P 2/2 2 V ariation list BHR262Z2C BHR262RD Model No. Type Quantity Battery adapter Battery converter Plastic carrying case Battery cover Yes Battery BHR262DP1 No No BHR262Z No 1 No No No No BAP36N BCV.
[2] LUBRICATION [1] NECESSARY REPAIRING TOOLS R epair Description Code No. Use for Retaining ring S pliers ST-2N 1R003 Removing Ring spring 19 from Tool holder complete/ Tool holder guide complete Ret.
Gear section: 17g Crank section: 5g boss for fixing Compression spring 14 [Inside view of Inner housing] [2] LUBRICATION (cont.) Apply Makita grease RB No.00 to the following portions indicated by black triangle to protect parts and product from unusual abrasion.
[3] DISASSEMBLY/ASSEMBLY [3] -1. Bit holder section for BHR262, HR262D Holder section for Drill chuck of BHR262T, HR262TD DISASSEMBLING for BHR262, HR262D DISASSEMBLING for BHR262T, HR262TD Ring 21 Ring 21 Guide washer Conical compression spring 21-29 Cap 35 Steel ball 7.
a Note: Face the chamfered end of the hole upward. Aligning the hole of Change ring with that of Change cover, assemble Change ring to Change cover. a' [Section a - a'] (1) Assemble Change ring to Change cover. ( Fig. 6 ) (2) Assemble Torsion spring 31 to Tool holder, then mount Steel balls 6 to Tool holder.
[3] DISASSEMBLY/ ASSEMBLY [3] -2. Drill chuck assembly for BHR262T, HR262TD DISASSEMBLING Fig. 10 Fig. 11 Fig. 14 Fig. 13 Fig. 12 Steel ball 5.0 Leaf spring Flat washer 24 Drill chuck assembly can be disassembled as drawn in Figs.
Change cover Change ring ASSEMBLING Chuck holder short arm of Torsion spring 31 long arm of Torsion spring 31 hole for Torsion spring 31 (1) Holding Chuck holder's flat portions in vise, assemble Drill chuck to Chuck holder by turning it clockwise using Hex wrench 10.
[3] DISASSEMBL Y/ASSEMBL Y [3]-3. Change lev er While pushing Lock button into Change lever, turn Change lever a little over Drill mode position to lock it in place. While pushing Lock button into Change lever, fit Change lever completely to Gear housing complete.
[3] DISASSEMBL Y/ASSEMBL Y [3]-4. Motor section, Switch Remove two Pins 6 and two 4x18 Tapping screws, then separate Handle (R) from Handle (L). Switch can now be replaced. (Also see Figs. D-1 and D-2 .) Remove two Pins 6 and Handle section from Housing (L) to disassemble Motor section.
[3] DISASSEMBL Y/ASSEMBL Y [3]-4. Motor section, Switch (cont.) Remove Brush holder on the right side by unscrewing two 4x18 Tapping screws. Motor section and Gear section can now be removed as an assembly. Brush holder (on right side) 4x18 Tapping screw (2 pcs.
When inserting Armature into Inner housing complete, do not fail to pass Armature through Yoke unit in advance. Note : Yoke unit is not directional when assembled with Armature. Without enough care, Ball bearing 6001DDW on the drive-end of Armature may often be incompletely seated in the bearing room of Inner housing complete.
[3] DISASSEMBL Y/ASSEMBL Y [3]-5. T ool holder section for BHR262, HR262D/ T ool holder guide section for BHR262T, HR262DT DISASSEMBLING Inner housing complete Flat washer 28 Piston cylinder Swash bearing section Take the disassembling step in reverse.
[3] DISASSEMBL Y/ASSEMBL Y [3]-6. Needle bearing complete and Oil seal 25 DISASSEMBLING Fig. 34 Fig. 37 ASSEMBLING 1) Assemble Oil seal 25 to Gear housing complete.
[3] DISASSEMBL Y/ASSEMBL Y [3]-7. Impact bolt in T ool holder complete for BHR262, HR262D)/ T ool holder guide complete for BHR262T, HR262TD DISASSEMBLING (1) When Striker is left in Tool holder (guide) complete, push Striker out of Tool holder (guide) complete by inserting 1R281 from the top end then by striking 1R281 with plastic hammer.
Note: 2) ASSEMBLING Fig. 42 Cushion ring 13 Ring 10 O ring case with O ring 9 fit inside Impact bolt 1) Assemble Impact bolt section to Tool holder (guide) complete as drawn in Fig. 42 . Tool holder (guide) complete Sleeve 9 Bit (chuck) installation side Inner housing complete side long short Fig.
[3] DISASSEMBL Y/ASSEMBL Y [3]-8. Swash bearing 10, Gear section DISASSEMBLING Fig. 44 Note : This step can be done without removing Motor section. 1) Remove Gear housing complete as instructed in [3]-5 . 2) Remove Inner support complete by loosening two M4x25 Hex socket head bolts using 1R170.
[3] DISASSEMBL Y/ASSEMBL Y [3]-8. Swash bearing 10, Gear section (cont.) ASSEMBLING Fig. 51 Fig. 52 Guide plate Note: Be sure to apply Makita grease RB No.
[4] Maintenance program It is recommended to replace the following parts at the same time when replacing Carbon brushes. ( Fig. 55 ) Note : Be sure to put Makita grease RB No. 00 and Molybdenum disulfide lubricant to the specific portions. Refer to Figs.
Color index of lead wires' sheath Black Terminal LED Brush holder Switch M1 White Red Fig. D-1 Terminal LED Line filters Switch C ircuit diagram P 2 0 /2 2 W ith Equipment of Radio Interference S.
W iring diagram Fig. D-2 T o Brush holder complete Connector Connector ribs Diode Switch Lead wire holders FET (Field effect transistor) Lead wires must be tight in the area shown in gray . Fix lead wires in the Lead wire holders indicated by dotted circle .
Lead wire (yellow) Terminal Line filters Tube Connector Lead wire (black) Yoke Connector FET Fig. D-3 Lead wire holder Lead wire holder Fix Lead wires (red, black) of Brush holder complete in these Lead wire holders. rib Light circuit W iring diagram P 2 2 /2 2 Line filter is not used for some countries.
Een belangrijk punt na aankoop van elk apparaat Makita HRH01 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita HRH01 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita HRH01 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita HRH01 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita HRH01 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita HRH01 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita HRH01 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita HRH01 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
