Gebruiksaanwijzing /service van het product HS7100 van de fabrikant Makita
Ga naar pagina of 16
Model No. Description PR ODUCT P 1/1 6 HS7100, HS7101 Circular Saw 190mm (7-1/2") Models HS7100, HS7101 have been developed as the successor models of the current model 5705R, featuring compact & lightweight design without riving knife.
P 2 / 16 R epair Apply the following grease/ lubricant to the specific portions to protect parts and product from unusual abrasion. [1] NECESSAR Y REP AIRING TOOLS CAUTION: Repair the machine in accordance with “Instruction manual” or “Safety instructions”.
3. Loosen M6x20 Hex bolt using Lever 45, then remove E-8 Bow stop ring with a slotted screwdriver . 6. Base can now be separated from the machine. 7. Base can be replaced after removing T op guide, Lock levers, and four M6x8 Hex socket set screws. 4. Remove M6x20 Hex bolt by using Lever 45 as a tool, then remove Flat washer 6.
P 4 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -1. Base Fig. 3 ASSEMBLING ASSEMBLING, ADJUSTMENT Base can be mounted to the machine by taking the reverse steps of Disassembling. Note: Follow the important instructions described in Fig. 2A . See Fig. 3 for Assembling and Adjustment of Lock lever for clamping Guide Rule .
P 5 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -3. Depth Guide Fig. 4 DISASSEMBLING Disassemble Depth guide as described in Fig. 4 . M6x18 Hex bolt M6x18 Hex bolt Lever 70 M4x8 Pan head screw Lock plate 1. Set the cutting depth of the machine to minimum.
P 6 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -3. Depth Guide Fig. 5 ASSEMBLING Assemble Depth guide section by taking the reverse step of Disassembling. ( Fig. 4 ) Note: Follow the important instructions described in Fig. 5 . M5x8 Hex socket set screw 1.
P 7 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -4. Angular Guide Fig. 6 DISASSEMBLING Angular guide can be disassembled as described in Fig. 6 . Assemble Angular guide by taking the reverse step of Disassembling. ( Fig. 6 ) M5 T russ head screw O Ring 9 Stopper Angular guide 4.
P 8 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -5. Blade Case, Blade Cover , Safety Cover Fig. 7 Fig. 8 DISASSEMBLING (1) Separate Motor housing and Armature from Blade case section as described in Fig. 7 . 1. Remove Carbon brush. 2. Remove three M5x45 Pan head screws.
P 9 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -5. Blade Case, Blade Cover , Safety Cover Fig. 9 Fig. 10 DISASSEMBLING (5) Remove Blade cover as described in Fig.
P 1 0 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -6. Helical Gear , Ball Bearing 6003DDW Fig. 12 Fig. 13 Fig. 1 1 DISASSEMBLING 1. Separate Bearing box from Spindle and Helical gear using arbor press as drawn below . Spindle Bearing box (2) Remove Spindle from Helical gear as described in Fig.
P 1 1 /1 6 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -7. Handle Cover , Electrical Parts in Handle [4] ADJUSTMENT [4]-1 Angle of Saw Blade to Base Fig. 14 Fig. 15 DISASSEMBLING 1. Lift up Handle cover in the direction of arrow . 2. T urn Handle cover in the direction of arrow .
P 1 2 /1 6 R epair [4] ADJUSTMENT [4]-2 Parallel Adjustment of Base to Saw Blade Fig. 16 (1) Attach saw blade to the unplugged machine, and set the cutting depth of the machine to maximum with the bevel angle adjusted to 90 degrees. (2) Make parallel adjustment of Base to saw blade as described in Fig.
C ircuit diagram P 1 3 /1 6 White Blue Brown Color index of lead wires' sheath Black Switch Brush holder R Brush holder F Noise suppressor Field, viewed from Blade case side Noise suppressor is not used for some countries. Fig. D-1 This Lead wire is white for some countries instead of blue.
W iring diagram P 1 4 /1 6 Switch Field Noise suppressor (if used) rib A rib B rib C rib D Fig. D-2 Route Field lead wires into Handle section through this groove. Field lead wires must be tight in Motor housing. If Noise suppressor is used, route Noise suppressor ’ s lead wires between rib A and rib B .
C ircuit diagram P 1 5 /1 6 Switch White Blue Brown Color index of lead wires' sheath Black Orange Y ellow Purple Field, viewed from Blade case side Fig. D-3 Noise suppressor is not used for some countries. Noise suppressor Brush holder R Brush holder F This Lead wire is white for some countries instead of blue.
W iring diagram P 1 6 /1 6 LED Light circuit Fig. D-4 Fix Field lead wires in these Lead wire holders. Switch Field Noise suppressor (if used) rib A rib B rib C rib D Field lead wires must be tight in Motor housing. If Noise suppressor is used, route Noise suppressor ’ s lead wires between rib A and rib B .
Een belangrijk punt na aankoop van elk apparaat Makita HS7100 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita HS7100 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita HS7100 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita HS7100 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita HS7100 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita HS7100 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita HS7100 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita HS7100 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
