Gebruiksaanwijzing /service van het product LS1030N van de fabrikant Makita
Ga naar pagina of 24
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.
2 SPECIFICATIONS Blade diameter : ............................................................................................. 255 mm (10”) Hole diameter : ........................................................................................... 15.
3 6. KEEP CHILDREN A W A Y . All visitors should be kept safe distance from w ork area. 7. MAKE WORKSHOP KID PR OOF with pad- locks, master s witches, or by removing starter keys. 8. DON’T FORCE T OOL. It will do the job bet- ter and safer at the rate f or which it was designed.
4 T OOL. Using a power source with v oltage less than the nameplate rating is harmful to the motor . USE PROPER EXTENSION CORD . Make sure y our extension cord is in good condition. When using an e xtension cord, be sure to use one heavy enough to carr y the current y our product will draw .
5 and pitch remover , hot water or kerosene. Never use gasoline to c lean blade. 11 . Use only flanges specified for this tool. 12. Be careful not to damage the arbor , flanges (especially the installing surface) or bolt. Damage to these parts could result in blade breakage.
6 SA VE THESE INSTR UCTIONS W ARNING: MISUSE or failure to fo llow the safety rules stated in this instruction manual ma y cause serious personal injury .
7 INST ALLA TION Benc h mounting When the tool is shipped, the handle is lock ed in the lowered position by the stopper pin. Release the stopper pin b y lower- ing the handle slightly and pulling the stopper pin. This tool should be bolted with two bolts to a le vel and stab le surf ace using the bolt holes provided in the tool’ s base.
8 If the see-through blade guard becomes dirty , or sawdust adheres to it in such a wa y that the blade is no longer easily visible , unplug the saw and clean the guard carefully with a damp cloth. Do not use solvents or an y petroleum-based cleaners on the plastic guard.
9 With the tool unplugged, rotate the blade b y hand while hold- ing the handle all the wa y down to be sure that the b lade does not contact any part of the lower base.
10 W ARNING: • NEVER use tool without a fully operativ e switch trigger . Any tool with an inoperativ e switch is HIGHL Y D ANGEROUS and must be repaired bef ore fur ther usage. • F or your saf ety , this tool is equipped with a lock-off button which pre vents the tool from unintended starting.
11 T o remove the b lade, use the sock et wrench to loosen the he x bolt holding the center cover b y tur ning it countercloc k- wise. Raise the b lade guard and center cover . Press the shaft lock to loc k the spindle and use the socket wrench to loosen the he x bolt clockwise.
12 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy . T o attach the dust bag, fit it onto the dust nozzle. When the dust bag is about half full, remov e the dust bag from the tool and pull the f astener out.
13 V ertical vise The vertical vise can be installed on the guide fence or the holder assembly (optional accessory). Inser t the vise rod into the hole in the guide f ence or the holder assembly and tighten the screw to secure the vise rod.
14 Holders and holder assembl y (optional accessories) The holders and the holder assembly can be installed on either side as a conv enient means of suppor ting workpieces horizontally . Install them as shown in the figure . Then tighten the screws firmly to secure the holders and the holder assembly .
15 1. Press cutting Secure the workpiece with the vise. Switch on the tool without the blade making an y contact and wait until the blade attains full speed bef ore lowering. Then gently lower the handle to the fully lo wered position to cut the workpiece.
16 Use the crown molding stoppers (optional accessories) when cutting the corners((1) - (4) in Fig.A). Install them on the base as shown in the figures . P osition crown molding with its W ALL CONT A CT EDGE against the guide f ence and its CEILING CONT A CT EDGE against the crown molding stoppers as sho wn in the figure.
17 CA UTION: • Use straight wood of e ven thic kness as the wood f acing. • Use screws to attach the wood f acing to the guide f ence. The screws should be installed so that the scre w heads are below the surf ace of the wood f acing. • When the wood f acing is attached, do not tur n the turn base with the handle lowered.
18 Carrying tool Make sure that the tool is unplugged. Secure the turn base at right miter angle fully by means of the grip . Lower the handle fully and lock it in the lo wered position by pushing in the stop- per pin. Carr y the tool b y carr ying grip as shown in the figure .
19 Lower the handle fully and loc k it in the lowered position by pushing in the stopper pin. Square the side of the blade with the f ace of the guide f ence using a tr iangular rule, try-square, etc. Then securely tighten the hex bolts on the guide f ence in the order from the r ight side.
20 AC C E S S O R I E S CA UTION: • These accessories or attachments are recommended for use with your Makita tool specified in this man ual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment f or its stated pur pose.
21 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut.
22 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2.
23 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St.
W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm.
Een belangrijk punt na aankoop van elk apparaat Makita LS1030N (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Makita LS1030N heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Makita LS1030N vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Makita LS1030N leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Makita LS1030N krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Makita LS1030N bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Makita LS1030N kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Makita LS1030N . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
