Gebruiksaanwijzing /service van het product MER8680BB van de fabrikant Maytag
Ga naar pagina of 16
INSTALLATION INSTR UCTIONS 30" (76 CM) FREESTANDING ELECTR IC RANGES T able of Conten ts RANGE SAFETY ................................ .................................. ................2 INSTALLATION RE QUIREMENTS ................ ..............
2 RANGE SAFETY You can be killed or seriously injured if you don't immediately You can be killed or seriously injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
3 INST ALLA TION REQUIREMENTS T ools and P ar ts Gather the req uired tools and part s befor e starting installation. Read and follow the instructions provided with any tools list ed here. T ools needed Parts supplied Check that all parts are included.
4 Product Dimensions IMPORT ANT : Range must be level after installation. Follow the instructions in the “Level Range” secti on. Using the cooktop as a refer ence for leveling the range is not recommended. * Range can be rai sed approximately 1" (2.
5 Electr ical Requirements - U .S.A. Only If codes permit and a separate ground wir e is used, it is recomm ended that a qualified elec trical installer determine that the ground path and wire gauge are in accordance with local codes. Do not use an extension cord.
6 INSTALLATION INSTR UCTIONS Unpack Range 1. Remove shipping materials, tape and film fr om range. 2. Remove oven racks and parts package from in side oven. 3. Do not remove the shipping base at this time. 4. On Ranges Equipped with a Storage Drawer: Remove the storage drawer .
7 Floor Mounti ng W all Mounting 5. Using the Phillips screwdriver , mount anti-tip bracket to the wall or floor with the two #12 x 1 ⁵⁄₈ " screws provided. 6. Move range close enough to opening to allow for final electrical connec tions. Remove shipping base, cardboar d or hardboar d from under range.
8 Electr ical Connection - U .S.A. Only 1. Disconnect power . 2. Remove the te rminal block cove r screws located on the bac k of the range. Pull cover down and towar d you to remove cover from range. 3. Remove plastic tag holding three 10-32 hex nuts from the middle post of the terminal block .
9 Style 2: Direct wir e strain relief ■ Remove the knockout as ne eded for the flexible conduit connection. ■ Assemble a UL listed conduit connector in the openi ng.
10 4. Use a Phillips screwdriver to connect the gr een ground wire from the power supply cord to the range with the ground-link screw and ground-link section. The ground wir e must be attached first. 5. Use ³⁄₈ " nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.
11 1. Part of metal ground strap must be cut out and r emoved. 2. Use a Phillips screwdriver to remove the gr ound-link screw from the back of the range. Save the ground-link scr ew and the end of the ground link under the screw . 3. Pull the wires thr ough the strain relief on bottom of range.
12 2. Attach terminal lugs to line 2 (red), bar e (green) gro und, and line 1 (black) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wir e end through bottom of terminal lugs. Securely tighten setscrew to to rqu e as s ho wn i n t h e f o ll ow i ng B are Wi re T o rqu e Specifications chart.
13 6. Repeat steps 1 and 2 to ensur e that the range foot is engaged in the anti-t ip bracket. If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, the a nti-tip bracket may not be installed correctly . Do not operate the range without anti-tip bracket installed and engaged.
14 Storage Draw er (on some models) The storage drawer can be removed. Before removing, make sure drawer is cool and empty . To R e m o v e : 1. Pull the storage drawer straig ht back to the drawer stop. 2. Lift up the fr ont of the dra wer and pull the drawer out.
15 Mo ving the Range When moving range, slide range onto cardb oard or hardboar d to avoid damaging the floor covering. If removing the range is necessary for cleaning or maintenanc e: For power supply cor d-connected ranges: 1. Slide range forward. 2.
W10403811C ® /™ ©2012 Whirlpool. All rights reser ved. 8/12 Printed in U.S.A..
Een belangrijk punt na aankoop van elk apparaat Maytag MER8680BB (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Maytag MER8680BB heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Maytag MER8680BB vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Maytag MER8680BB leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Maytag MER8680BB krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Maytag MER8680BB bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Maytag MER8680BB kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Maytag MER8680BB . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
