Gebruiksaanwijzing /service van het product W10306460A-SP van de fabrikant Maytag
Ga naar pagina of 20
1 W10096988A W10306460A-SP DR YER SAFETY ......................................................................... 2 INST ALLA TION REQUIREMENTS ............................................. 3 T ools and Parts .........................................
2 DR YER SAFETY You You can be killed or seriously injured if you don't immediately can be killed or seriously injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
3 INST ALLA TION REQUIREMENTS T ools and Parts Gather the requir ed tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
4 If you are using power supply cor d, a grounded electrical ■ outlet located within 2 ft. (610 mm) of either side of dryer . See “Electrical Requirements.” A sturdy oor to support the total weight (dryer and load) ■ of 200 lbs. (90.7 kg). The combined weight of a companion appliance should also be considered.
5 Electrical Connection T o properly install your dryer , you must determine the type of electrical connection you will be using and follow the instructions provided for it her e. If local codes do not permit the connection of a neutral ■ ground wir e to the neutral wire, see “Optional 3-wir e connection” section.
6 Install Leveling Legs Prepar e dryer for leveling legs 1. T o avoid damaging oor , use a large at piece of car dboard from dryer carton; place under entir e back edge of dryer . Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboar d.
7 Electrical Connection Power Supply Cord W ARNING Fire Hazar d Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wir e) to center terminal (silver).
8 Put power supply cord thr ough the strain relief. Be sur e that the wire insulation on the power supply cor d is inside the strain relief. The strain r elief should have a tight t with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief scr ews at this point.
9 3-wir e Power Supply Cor d Connection Use where local codes permit connecting cabinet-gr ound conductor to neutral wire. A B D C E F G A. 3-wire receptacle (NEMA type 10-30R) B. 3-wire plug C. Neutral prong D. Spade terminals with upturned ends E. 3/4" (19 mm) UL listed strain relief F .
10 4-wir e Direct Wir e Connection IMPORT ANT : A 4-wire connection is r equired for mobile homes and where local codes do not permit 3-wir e connections. 5. Prepar e to connect neutral ground wir e and neutral wir e E A B Remove center , silver -colored terminal block scr ew (B).
11 3-wir e Direct Wir e Connection Use where local codes permit connecting cabinet-gr ound conductor to neutral wire. B 5. Remove center screw Remove center , silver -colored terminal block scr ew (B). 7. Connect ground wir e A F Connect ground wir e (green or bar e) (F) of direct wir e cable to external ground conductor screw (A).
12 1. Prepar e to connect neutral ground wir e and neutral wir e A E B Remove center , silver -colored terminal block scr ew (B). Remove neutral ground wir e (E) from external ground conductor screw (A). E B C Connect neutral ground wir e and neutral wire 2.
13 V enting Requirements W ARNING Fire Hazar d Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in death or re. WARNING: T o r educe the risk of re, this dryer MUST BE EXHAUSTED OUTDOORS.
14 Plan V ent System Recommended exhaust installations T ypical installations vent the dryer from the r ear of the dryer . Other installations are possible. B B C D E F G H I A A. Dryer B. Elbow C. Wall D. Exhaust hood E. Clamps F . Rigid metal or exible metal vent G.
15 Install V ent System 12" min. (305 mm) 12" min. (305 mm) Install exhaust hood 1. Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood. Connect vent to exhaust hood 2. V ent must t over the exhaust hood.
16 Level Dryer Level Dryer 1. Not Level LEVEL Not Level Check levelness of dryer from side to side. Repeat fr om front to back. NOTE: The dryer must be level for the moisture sensing system to operate correctly . Move dryer to nal location 2. Move dryer to nal location.
17 Reverse Door Swing (Optional) Place towel on dryer 1. Place towel on top of dryer to avoid damaging the surface. Lift door until top screws in dryer cabinet ar e in large part of hinge slot. Pull door forward of f screws. Set door (handle side up) on top of dryer .
18 Remove and transfer plugs 9. Remove the 4 screws that attach 2 plugs on the left side. T ransfer plugs to opposite side using the same 4 screws. Attach door hinges 8. Reattach door hinges to dryer door so that the lar ger hole is at the bottom of the hinge.
19 Notes.
20 W10096988A W10306460A-SP © 2010 Whirlpool Corporation. 2/10 All rights reserved Printed in U.S.A. ® Registered T rademark/TM T rademark of Whirlpool, U.
Een belangrijk punt na aankoop van elk apparaat Maytag W10306460A-SP (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Maytag W10306460A-SP heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Maytag W10306460A-SP vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Maytag W10306460A-SP leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Maytag W10306460A-SP krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Maytag W10306460A-SP bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Maytag W10306460A-SP kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Maytag W10306460A-SP . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
