Gebruiksaanwijzing /service van het product MCC215 van de fabrikant Memorex
Ga naar pagina of 48
memorexelectronics.com MCC21 5 User Guide Please read these instructions completel y, before operating this product. V ide o Cam er a Digital Let ’s Make Me mor ies.
Contents ................................................1 Safety Precautions ................................2 Location of Controls ...........................4 Using the Strap ...................................6 Getting Started ....................
2 SAFETY PRECAUTIONS FCC W ARNIN G: Thi s equipm ent may g enera te or use r adio fre quenc y energ y . Cha nges or m odific ation s to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.
3 Be sure to observe the following precautions when using the unit: • This unit works best when used in bright lighting, such as sunlight or a brightly-lit room. Results in dimly-lit areas will vary . • Never attempt your own repairs. Always leave service to authorized repair facilities.
LOCA TION OF CONTROLS 4 1 6 7 8 9 2 3 4 5 1. Up π Button 2. OK Button 3. Display 4. Down † Button 5. MENU Button 6. Power Button 7. Mode Control 8. SHUTTER Button 9. USB/TV OUT Jacks (Under Compartment) A V CABLE P ART NO. E532R4POLAR0001* USB CABLE P ART NO.
1 3 2 5 6 4 6 5 LOCA TION OF CONTROLS (CONTINUED) 1. Battery Compartment ( BA TTERY COVER P ART NO. P337RBDV096C01 1*) 2. Speaker 3. Lens 4. SD/MMC Card Slot (Bottom of Unit) 5. Microphone 6. Strap Holders (HANDSTRAP P ART NO. K910RDV096C0001*) CD P ART NO.
6 USING THE STRAP Fold over the Strap Flap and connect as shown. Adjust as desired to fit your hand. Insert the V elcro straps into each of the Strap Holders.
GETTING ST ARTED 7 1 Slide the cover back on. NOTE: When the batteries are low , the battery low indicator will blink in the display . BA TTER Y PRECAUTIONS Follow these precautions when using batteries in this device: 1. Use only the size and type of batteries specified.
GETTING ST ARTED (CONTINUED) 8 1 2 Press the Power button to turn the unit on. “Memorex” will appear briefly in the display . TURNING THE POWER ON AND OFF Press an d hold the Powe r button unti l “Goodbye” appears in the display (appro ximately on e second).
9 GETTING ST ARTED (CONTINUED) HINTS ON USING AN SD/MMC CARD : 1. When an SD/MMC card is inserted, the Card indicator will appear in the display and new pictures taken will be stored on the SD/MMC card automatically . 2. Push the SD/MMC card all the way in to make sure the SD/MMC card is fully inserted.
2 1 OPERA TION 10 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Picture T aking position. 1 T AKING A SINGLE PICTURE P V SET SET Press the Up π button 1 to zoom in or the Down † button 2 to zoom out as desired. This zoom function works only for resolutions of 640 x 480 and 1280 x 1024.
OPERA TION (CONTINUED) 11 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Picture T aking position. 1 CHANGING THE PICTURE MODE P V SET SET Press the MENU button and the settings will appear . 2 Press the Up π button 1 or the Down † button 2 to select the Picture Mode setting (see above).
OPERA TION (CONTINUED) 12 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Picture T aking position. 1 CHANGING THE PICTURE RESOLUTION P V SET SET Press the MENU button and the settings will appear . 2 Press the Up π button 1 or the Down † button 2 to select the Resolution setting (see above).
OPERA TION (CONTINUED) 13 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Picture T aking position. 1 CHANGING THE WHITE BALANCE P V SET SET Press the MENU button and the settings will appear . 2 Press the Up π button 1 or the Down † button 2 to select the White Balance setting (see above).
OPERA TION (CONTINUED) 14 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Picture T aking position. 1 CHANGING THE EV COMPENSA TION P V SET SET Press the MENU button and the settings will appear . 2 Press the Up π button 1 or the Down † button 2 to select the EV Compensation setting (see above).
OPERA TION (CONTINUED) 15 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Picture Viewing position. 1 VIEWING THE PICTURES P V SET SET Press the Up π button 1 or the Down † button 2 to select other pictures. 2 1 2 2 1 3 T o delete the selected picture, press the MENU button 1 .
OPERA TION (CONTINUED) 16 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Video T aking position. 1 RECORDING A VIDEO P V SET SET Press the Shutter button and then the unit will start recording the video and the counter will start counting.
OPERA TION (CONTINUED) 17 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Video Recording position. 1 CHANGING THE VIDEO RESOLUTION P V SET SET Press the MENU button and the settings will appear . 2 Press the Up π button 1 or the Down † button 2 to select the Resolution setting (see above).
OPERA TION (CONTINUED) 18 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Video Recording position. 1 CHANGING THE WHITE BALANCE P V SET SET Press the MENU button and the settings will appear . 2 Press the Up π button 1 or the Down † button 2 to select the White Balance setting (see above).
OPERA TION (CONTINUED) 19 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Video Recording position. 1 CHANGING THE EV COMPENSA TION P V SET SET Press the MENU button and the settings will appear . 2 Press the Up π button 1 or the Down † button 2 to select the EV Compensation setting (see above).
OPERA TION (CONTINUED) 20 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the Video V iewing position. 1 VIEWING THE VIDEOS P V SET SET Press the Up π button 1 or the Down † button 2 to select a video. Press the OK button 3 to start playback.
OPERA TION (CONTINUED) 21 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the SET position. 1 SETTING THE DA TE AND TIME P V SET SET Press the Up π button 1 or the Down † button 2 to select the T ime Set option. Press the OK button 3 ; the T ime Set screen will appear .
OPERA TION (CONTINUED) 22 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the SET position. 1 SETTING THE DA TE/TIME ST AMP (ON PICTURES) P V SET SET Press the Up π button 1 or the Down † button 2 to select the Date Stamp option.
OPERA TION (CONTINUED) 23 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the SET position. 1 FORMA TTING THE SD/MMC CARD P V SET SET Press the Up π button 1 or the Down † button 2 to select the Format setting. 2 1 2 Press the OK button; “Y” and “N” will appear .
OPERA TION (CONTINUED) 24 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the SET position. 1 SETTING THE LIGHT FREQUENCY P V SET SET Press the Up π button 1 or the Down † button 2 to select the Frequency setting.
25 OPERA TION (CONTINUED) 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the SET position. 1 SETTING THE PC CAMERA/MASS STORAGE P V SET SET Press the Up π button 1 or the Down † button 2 to select the PC Camera/Mass Storage setting.
OPERA TION (CONTINUED) 26 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the SET position. 1 VIEWING THE VERSION P V SET SET Press the Up π button 1 or the Down † button 2 to select the V ersion. 2 1 2 Press the OK button to view the current firmware version.
OPERA TION (CONTINUED) 27 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the SET position. 1 SETTING THE ICON P V SET SET Press the Up π button 1 or the Down † button 2 to select the Icon setting. 2 1 2 Press the MENU button 1 to select the desired mode (see above), and then press the OK button 2 to confirm.
OPERA TION (CONTINUED) 28 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the SET position. 1 TURNING THE RECORDED AUDIO ON AND OFF DURING VIDEO PLA YBACK P V SET SET Press the Up π button 1 or the Down † button 2 to select the Audio On or Off setting.
OPERA TION (CONTINUED) 29 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the SET position. 1 CHANGING THE TV SYSTEM P V SET SET Press the Up π button 1 or the Down † button 2 to select the TV System setting. 2 1 2 This is used when connecting the A V cable to your TV .
OPERA TION (CONTINUED) 30 2 1 Press the Power button 1 to turn the unit on. Rotate the Mode control 2 to the SET position. 1 DEF AUL T SETTING P V SET SET Press the Up π button 1 or the Down † bu tto n 2 to se lec t the D efa ult setting. 2 1 2 Press the OK button.
31 CONNECTING THE UNIT TO A TV Y ou can connect this unit to a TV using the supplied A/V cable. This will allow you to view the unit’s videos and pictures on a non-high definition (non- HD) television. First, make sure to set the TV SYSTEM to NTSC or P AL, corresponding to your TV color system as shown on page 28, then connect as follows.
CONNECTING YOUR CAMERA TO YOUR PC: Once you have taken a few pictures/videos with your camera or as soon as the camera’s memory is full, you can download the files into your computer . Connect your camera to the PC, following these simple steps: 1. T urn on your computer .
SOFTW ARE INST ALLA TION 33 SUPPORTED OPERA TING SYSTEMS This unit is compatible with Microsoft Windows XP (Home or Professional Edition with Service Pack 2 or higher) or Vista. • Before and while installing the software, make sure that you do not have the camera attached to your computer .
Installing PhotoImpression and VideoImpression 1. After completing the Driver installation, click “Phot o & Video Edi ting”. 2. Click “Video Impression” and follow the on-screen instructions to install the VideoImpression software.
DOWNLOADING AND TRANSFERRING FILES 35 TRANSFERRING PHOTO/VIDEO FILES FROM THE UNIT USING DRAG AND DROP METHOD USING WINDOWS 1. T urn on your computer . 2. T urn on the unit. 3. Connect the smaller end of the cable to the USB jack on the unit and the larger end of the cable to your USB port on your PC.
See below for basic instructions on using the PhotoImpression software. For full features/instructions, click the “?” (top right corner of the window) or visit Arcsoft’s website. 1. Click ST ART c PROGRAMS c Arcsoft PhotoImpression4 c PhotoImpression4.
See below for basic instructions on using the VideoImpression software. For full features/instructions, click the “?” (top right corner of the window) or visit Arcsoft’s website. 1. Click ST ART c PROGRAMS c Arcsoft VideoImpression 1.6 c VideoImpression 1.
1. Set the Camera to PC Camera, as described on page 25. 2. Connect the camera to the computer as described on page 32. 3. Double click the “PC Camera” icon on your desktop, the screen at the right will appear . 4. Click the ® icon and then click to start the image capture.
6. Use the following icons to capture and save still photos: 7. Click FILE –> ST ART CAPTURE to start the preview . 8. Click FILE –> SET CAPTURE FILE, then name the file. Click OPEN and then set the file size as desired. Click OK. 9. Click CAPTURE –> ST ART CAPTURE FILE, then click OK to start recording the live video sequence.
40 SA FE L Y R EM OV IN G THE H AR DW ARE SAFEL Y REMOVING THE UNIT FROM THE COMPUTER NOTE: T o avoid damage to the unit or data loss, always follow the procedure listed below before disconnecting the unit from the USB port on your computer . Using your mouse, double click the "Safely Remove Hardware" icon on the task bar .
TROUBLESHOOTING GUIDE 41 If you experience a problem with this unit, check the chart below before calling for service. Symptom Possible Cause Solution Unit will not turn on. Power is off. Press the Power button for one second to turn on. Batteries are weak or dead.
TROUBLESHOOTING GUIDE (CONTINUED) 42 Can’t take video/picture. Memory is full. Delete some pictures/videos. Power is off. Press the Power button for one second to turn on. When connected to a TV , picture is poor . Options are set incorrectly . Set TV System to P AL or NTSC.
43 Formatting the Player W ARNING! Do not format this player unless it stops working and you are instructed to do so by technical support personnel. 1. Use the USB cable to connect the player and the computer . 2. Double click on My Computer , then right click "Removable Disk" and left click on "Format".
44 If the unit acts erratically , reset the unit by removing the batteries for a couple of seconds and then reinserting. FOR FIRMW ARE UPGRADE Please visit our Web site at www .memorexelectronics.com to check if there is new firmware available. IMPORT ANT NOTE: Before upgrading the firmware, please backup all of your media files on your computer .
SPECIFICA TIONS 45 System Requirements and Compatibility • Operating System: For PC: Windows XP (SP2)/V ista • USB 1.1 • CD-ROM Drive If you have questions regarding your system specifications, please call your PC manufacturer . Camera Specifications Internal Memory .
FOR ADDITIONAL SET -UP OR OPERA TING ASSIST ANCE, PLEASE VISIT OUR WEBSITE A T : WWW .MEMOREXELECTRONICS.COM FOR CONSUMER REPLACEABLE P ART(S), SEE P ART NUMBER(S) ON P AGES 4 AND 5 AND THEN CONT ACT FOX INTERNA TIONAL A T : 1-800-321-6993. FOR FIRMW ARE UPGRADE, PLEASE VISIT OUR WEBSITE A T WWW .
Memorex, the Memor ex logo, and "Is it live or is it Memorex?", ar e trademarks of the afliates of Memorex Pr oducts, Inc. Imation Electronic Products, A Division of Imation Enterprises Corp., Weston, Florida. Printed in China www.memorexelectronics.
Een belangrijk punt na aankoop van elk apparaat Memorex MCC215 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Memorex MCC215 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Memorex MCC215 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Memorex MCC215 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Memorex MCC215 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Memorex MCC215 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Memorex MCC215 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Memorex MCC215 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
