Gebruiksaanwijzing /service van het product SP907NL van de fabrikant MicroNet
Ga naar pagina of 51
User ’ s Manual 1 1n W ireless LAN USB Adapter Model No.: SP907NL http://www.micronet.info.
Table of Contents Chapter 1 Introduction ................................................................................. 1 1.1 Package C ontents .......................................................................................... 1 1.2 Key Features .
4.6 Statistic s ...................................................................................................... 40 4.7 About ........................................................................................................... 41 Chapter 5 Troubleshooting .
1 Chapter 1 Introduction Micronet SP907NL, 11N Wireless LAN USB Adapter, delivers next generation high speed at a more economical and affordable pr ice tag. It is easily implemented for medium-sized business to allow imm ediate access to high speed wireless experience.
2 y WPS configuration for easier c onnection between adapter and AP/router. Enable connection via pushing a butt on or entering an 8-digit code. y Support the commonly available interface USB 2.
3 1.5 Specifications Standards IEEE802.11b/ 802.11g / 802.11n Interface USB 2.0/1.1 Frequency Band 2.4000 ~ 2.4835GHz Data Rate z 11b: 1/2/5.5/11Mbps z 11g: 6/9/12/24/36/48/54Mbps z 11n (20MHz): MCS0-7 (up to 72Mbps) z 11n (40MHz): MCS0-7 (up to 150Mbps) Output Power z 11n: 14dBm ± 1.
4 Chapter 2 Tour of Product 2.1 USB Adapter 1. USB Connector: insert this side of the device into an available USB slot. 2. Connector Cab: for protecting device when not in use. 3. WPS button: located on the bottom side of the device for activating WPS pairing mode.
5 Chapter 3 Configuration 3.1 Drivers Installation Step 1. Gently insert the USB adapter into an available USB slot. The following message will appear, please press <Cancel> . Step 2. Insert driver CD into the CD/DVD ROM drive of the computer, and execute ‘Setup.
6 Step 3. It is recommended to select ‘Install driver and Ralink WALN Utility’ for first-time installation. Otherwise select second option to update existing drivers. Step 4. The following windows will appear, pleas e press on ‘Install’ to start the process.
7 Step 5. Click <Finish> to complete the driver installation process. 3.2 Operating Configuration Utility After installation is complete, wireless configuration utility will be shown as an icon at the lower-right corner of the windows desktop. Click on the icon using right mouse key and select <Launch Config Utilities>.
8 Step 1. Configuration utility will scan for available wireless access points automatically. Please select an access point to connect, and click <Connect> . If the AP you wish to connect is not in the list, please press <Rescan> to renew the interface.
9 3.2.1 Scan for Other Wireless Devices There are two kinds of wireless connec tion mode: Infrastr ucture and Ad-Hoc. Infrastructure mode is used by wirel ess access points, which is able to establish wireless connection for you and other wireless/wired network clients.
10 y If the wireless device uses encryption, the user must know its encryption key in order to connect. Please launch utility and it will scan for wireless access points near by: Parameter Description SSID The SSID of the wireless access point or wireless d evice selected by user will be displa yed here.
11 If users cannot see the access point, please click ‘Rescan’ button to scan for access point again, until t he one preferred is displayed on the interface. Users may have to click ‘Rescan’ for more than two times before the access point wish to connect appears.
12 Step 1. Click the wireless access point or network device to connect, it will be highlighted, then click on ‘Connect’. If the access point selected does not use encryption, it will connect to this device within one minute. If the access poi nt selected uses encryption, please proceed to step 3.
13 Step 4. Please ask the owner of the wirele ss access point for the security information, and input the correct key here and then click on ‘OK’. By checking ‘Show Password’ box, the encryption key inputted here will be display ed. Authentication type will be selected by t he access point automatically, pleas e do not change it.
14 3.2.3 Add Access Point to Profile If users connect to some specific wireless access point frequently, they can add their information to the profile. Just lik e the telephone direct ory, the profile saves all information of access points, and user can recall them anytime.
15 Parameter Description Profile Name User can give this profile a name. Every profile need s a unique name. SSID Please input the SSID of this access point. If user selected a n access point from the list, and SSID is not hidden, it will be filled automatically.
16 Parameter Description Authentication Select the authentication type of the wireless access point or wireless device in this field. When users are ad ding a profile from an existing access point or wireless device, authentication type will be selected automatically.
17 Parameter Description EAP Method Select ‘802.1x EAP method’ from dropdown menu. Please ask the administrator of the access point for the correc t EAP method. Tunnel Authentication Select 802.1x tunnel authentic ation type from dropdown menu. Please ask the administrator of the acce ss p oint for correct tunnel authentication met hod.
18 3.2.4 Using Windows Zero Configuration Windows XP and Vista has a built-in wirel ess network configuration utility, called ‘Windows Zero Configuration’ (WZC).
19 Step 3. Click <Network Connections> . Step 4. Right-click ‘Wireless Network Connection’ (it may have a number as suffix if you have more than one wireless network card, please make sure you right-click the ‘802.11n Wireless LAN Card), then select ‘View Available Wireless Networks’.
20 to the access point. Otherwise, users c an press refresh butt on to rescan access points. Select the access point if it’s shown, then click <Connect> . Step 6. If the wireless access point uses encryption, users will have to input the correct WEP passphrase or WPA pre-shar ed key.
21 3.2.5 Profile Management If users need to connect to different wireless access points at different time, they can store the connection parameters (e ncryption, passphrase, security etc, etc.) as a profile for every access poin t. Click the ‘Profile’ menu and all profiles will be listed in ‘Profile Li st’.
22 Add a Profile If users want to create new profile, click ‘Profile’ menu, then press ‘Add’ button. The interface will prompt the user to input detailed information of access point.
23 If users have added a profile before, and th ey wish to change the content of the profile, they can use this function. Please select a profile from the list, and then click on ‘Edit’ button. The interface will provide contents of selected profile for editing.
24 Activate a Profile When users want to connect to a specific wireless device in the profile list, they can select it and click ‘Activate’ button to establish connection.
25 When a profile is selected and cl ick on ‘Activate’ button, an icon will be displayed in front of the profile to show that the connection has failed. When the connection is successfully established, an icon will be displayed. 3.2.6 Advanced Settings This wireless network card provides several advanced settings for experienced wireless users.
26 Enable CCX Enable Cisco Compatible eXtensi on s. CCX is a wireless feature developed by Cisco used to imp rove the wi rel ess performance with CCX compatible wirel ess devices. Check this box if the users need to connect to CCX -compatible wireless devices.
27 3.2.8 WMM Setting This wireless network card provides WM M (Wi-Fi Multimedia) function, which can improve the performance of certain network applications, like audio/video streaming, network telephony (VoIP), and others.
28 3.2.9 WPS Configuration Wi-Fi Protected Setup (WPS) is the la test wireless network technology, which makes wireless network setup become very simple. The user doesn’t have to configure the wireless access point and setup data encryption when devices support WPS.
29 All access points with WPS function enabled will be displayed her e. Please make sure the access point users wish to connect is displayed. If not, please click ‘Rescan’ few more times. The user can also click ‘Information’ button to see the detailed information about selected access point.
30 Users can click ‘PBC’ button few more times to try again. When an access point is connected, users can click ‘Disconnect’ to disconnect your wireless network card from a connected access point. Users can also click ‘Rotate’ button, and next access point on the list will be selected to establish connection.
31 Parameter Description WPS associate IE Check this box to send the association reque st with WPS IE during WPS setup. WPS probe IE Check this box to send the WPS probe request with WPS IE during WPS setup. Auto When in PIN mode, wireless ac cess point to be connected will be selected automatically if this box is checked.
32 3.2.11 About The ‘About’ tab provides the info rmation about version number of the configuration utility, driv er, and other important information about the wireless network card.
33 Chapter 4 Soft-AP Function Besides becoming a wireless client of other wireless access points, this wireless card can also act as a wireless service provider. Users can switch this wireless card’s operating mode to ‘AP’ to simulate the function of a real wireless access point by software and ev en sharing the internet connection.
34 If the computer has another network card which is connected to Internet, please select it from ‘Name’ dropdown menu, and click ‘Enable ICS’. If your computer does not have another network card with In ternet connection, please click ‘Not enable ICS’.
35 Parameter Description SSID Please input the SSID (the name used to identify this wireless access point) in this field. Up to 32 numeri cal charact ers can be accepted here excepting spa ce. Channel Please select the wireless cha nnel to use for the environment.
36 Country Region Code Please select the country code of the country or regio n. Available options are 0-7, wh ich will affect the available wireless channels: 0: FCC (US, Canada, and other countrie s.
37 Parameter Description Authentication Type Please select a wireless authenticatio n type to use. Available options are ‘Open’, ‘Share d’, WPA-PSK’, ‘WPA2-PSK’, and ‘WPA-PSK / WPA2-PSK’. If users wa nt to disable wireless data encryption, please select ‘Open’.
38 WEP Key Please input the WEP encryption key in this field when ‘WEP’ is selected. There are 2 types of WEP key: Hex (number 0 to 9, and ASCII characters A to F) and ASCII (all alphanumerical characters plus symbols). Please sel ect the type of WEP key first, and then input the WEP key according to the type of WEP key select ed.
39 Parameter Description Access Policy Select the policy type of your access rule. ¾ Disable: Allow any wireless client with p rop er authentication settings to connect to this access poin t. ¾ Allow All: Only allow wire less client s with MAC address listed here to connect to this access point.
40 Parameter Description MAC Address Displays the MAC address of this wireless client. AID The serial number of this wireless connection. Power Saving Mode Displays the capability of pow er-saving function of this wireless client.
41 4.7 About The ‘About’ tab provides the info rmation about version number of the configuration utility, driv er, and other important information about the wireless access point.
42.
43 Chapter 5 Troubleshooting If users encounter any problem when using th is wireless network card, consult this section for possible solutions. Before calli ng the dealer of purchase for help, please check this troubleshooting table, the solu tion towards the problem could be very simple.
44 Chapter 6 Glossary 1. What is the I EEE 802.11g standard? 802.11g is the new IEEE standard for hi gh-speed wireless LAN communications that provides up to 54 Mbps data rate in the 2.4 GHz band. 802.11g is quickly becoming the next mainstream wireless LA N technology for the home, office and public networks.
45 z RTS/CTS Feature z Fragmentation z Power Management 4. What is Ad-hoc? An Ad-hoc integrated wireless LAN is a group of computers with their own Wireless LAN Card connecting as an independent wire less LAN. Ad hoc wireless LAN is applicable at a departmental scale fo r a branch or SOHO operation.
46 9. What is AES? AES (Advanced Encryption Standard), a ch ip-based security, has been developed to ensure the highest degree of security and authenticity for digital information, while making more efficient use of har dware and/or software than previous encryption standards.
47 13. What is Spread Spectrum? Spread Spectrum technology is a wi deband radio frequency technique developed by the military for use in reliable, secu re, mission-critical communication systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security.
48 16. What is GI? GI stands for Guard Interval. It’s a measure to protect wireless devices from cross- interference. If there are two wireless devic es using the same or near channel, and they are close enough, radio interference will occur and reduce the radio resource usability.
Een belangrijk punt na aankoop van elk apparaat MicroNet SP907NL (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen MicroNet SP907NL heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens MicroNet SP907NL vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding MicroNet SP907NL leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over MicroNet SP907NL krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van MicroNet SP907NL bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de MicroNet SP907NL kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met MicroNet SP907NL . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
