Gebruiksaanwijzing /service van het product CS 1212-1 van de fabrikant Miele
Ga naar pagina of 60
Operating and installation instructions Ceramic hobs with induction CS 1212-1 CS 1221-1 CS 1222 To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. M.
Guide to the appliance .............................................4 CS 1212-1 ........................................................4 CS 1221-1 ........................................................5 CS 1222 .....................................
Optional accessories ..............................................4 0 Safety instructions for installation ...................................4 1 Appliance and building-in dimensions ...............................4 6 CS 1212-1 ......................
CS 1212-1 a Cooking zone with twin booster (BI/II) b Cooking zone with single booster (Bl) c Display d Cooking zone symbols e Indicators Cooking zone controls: f Rear g Front Indicators l In-operation.
CS 1221-1 a Cooking zone with twin booster (BI/II) b Display c Indicators d Control Indicators l In-operation indicator m Booster indicator n Residual heat indicator Guide to the appliance 5.
CS 1222 a Extended cooking zone with Twinbooster (B I/II) b Cooking zone with single booster (Bl) c Display d Cooking zone symbols e Indicators Cooking zone controls: g Front h Rear Indicators l In-op.
Display ß = No pan on cooking zone or pan unsuitable A = Auto heat-up I = Booster I II = Booster II (only for cooking zones with twin boosters) L = Safety lock (see "Safety features") Cooki.
Cooking zone CS 1222 minimum to maximum C in cm* Rating in watts for 230 V** Front 10 - 16 normal: with booster: 1400 2200 Rear 14 - 20 / 2 0x3 0 normal: with Booster I: with Booster II: normal: with Booster I: with Booster II: 1850 2500 3000 2300 3000 3700 Total: 3700 * Pans of any diameter within the given range may be used.
This appliance complies with current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time.
Correct application ~ This appliance is not designed for commercial use. It is intended for use in domestic households and in similar working and residential environments such as: – Shops – Offices and showrooms and by residents in establishments such as: – Hostels and guest houses.
Safety with children ~ Activate the safety lock to ensure that children cannot switch on the appliance inadvertently. ~ This appliance is not a toy! To prevent the risk of injury, do not let children play with the appliance or its controls. ~ Children under 8 years of age must be kept away from the hob unless they are constantly supervised.
~ Keep all pans out of reach of children. Turn pan handles inwards away from the edge of the hob. Danger of burning or scalding. Special hob guards are available from good retail outlets. ~ Packaging, e.g. cling film, polystyrene and plastic wrappings, must be kept out of the reach of babies and young children.
~ Before connecting the appliance, make sure that the connection data on the data plate (voltage and frequency) match the mains electricity supply. This data must correspond in order to avoid the risk of damage to the appliance. Consult a qualified electrician if in any doubt.
~ While the appliance is under guarantee, repairs should only be undertaken by a service technician authorised by Miele. Otherwise the guarantee is invalidated. ~ Faulty components must only be replaced by genuine Miele original spare parts. The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used.
~ This appliance may be connected via a fused plug and switched socket. If you wish to connect it to an isolator switch, or if the appliance is supplied without a plug, it must be installed and connected by a suitably qualified and competent person in strict accordance with current local and national safety regulations.
~ The appliance gets hot when in use and remains hot for quite a while after being switched off. There is a danger of burning until the residual heat indicators go out. ~ Do not leave the appliance unattended whilst it is in use. Pans that have boiled dry can cause damage to the ceramic surface for which Miele cannot be held liable.
~ Do not use the appliance as a resting place for anything else. Take particular care never to place cutlery or other metal objects on the appliance. When the appliance is switched on either deliberately or by mistake, or when there is residual heat present, there is the risk of metal objects heating up, with a danger of burning.
~ Do not use pots and pans on the ceramic hob with bases with pronounced edges or ridges, e.g. cast iron pans. These could scratch or scour the hob surface permanently. ~ Never heat an empty pan unless the manufacturer of the pan expressly states that you can do so.
~ Do not allow either solid or liquid sugar, or pieces of plastic or aluminium foil to get onto the cooking zones when they are hot. If this should occur, switch off the appliance, and carefully scrape off all the sugar, plastic or aluminium residues from the hob whilst they are still hot, using a shielded scraper blade.
~ Spray canisters, aerosols and other inflammable substances should not be stored in a drawer under the hob. Cutlery inserts must be heat-resistant. ~ Metal utensils stored in a drawer under the hob can become hot if the induction hob is used intensively for a long time.
Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions. Warning and Safety instructions 21.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children.
Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service, data plate" section of this booklet. Cleaning for the first time ^ Remove any protective wrapping and adhesive labels.
The induction principle An induction coil is located under each cooking zone. When a cooking zone is switched on, this coil creates a magnetic field which impacts directly on the base of the pan and heats it up. The cooking zone itself is heated up indirectly by the heat given off by the pan.
Noises When using an induction cooking zone, the following noises can occur in the pan, depending on what it is made of and how it has been constructed. – On the higher power settings, it might buzz. This will decrease or cease altogether when the power setting is reduced.
Pans Suitable pans include: – stainless steel pans with a magnetic base – enamelled steel pans – cast iron pans Unsuitable pans: – stainless steel pans without a magnetic base – aluminium an.
Switching on and off Each cooking zone is switched on by turning the control clockwise a to the power setting required, and is switched off by turning the control anticlockwise b to "0". Do not turn the control to "0" by turning it past BI or BI/II.
Settings Cooking process Settings* Keeping warm ( Melting butter Dissolving gelatine 1-2 Making milk puddings 2 Warming small quantities of liquid Cooking rice Defrosting frozen vegetables Cooking pul.
Auto heat-up Continued cooking setting Heat-up time in minutes and seconds (approx.) 1 0:1 5 2 0:1 5 3 0:2 5 4 0:5 0 5 2:0 0 6 5:5 0 7 2:5 0 8 2:5 0 9- When Auto heat-up has been activated, the cooking zone switches on automatically at the highest setting and then switches to the continued cooking setting which you have previously selected.
Booster function The cooking zones are equipped with Single (l) or Twin Boosters (I/II) (see "Guide to the appliance"). When activated, the power is boosted so that large quantities can be heated quickly, e.g. boiling water for cooking pasta.
To activate Booster l ^ Turn the control past power setting 9 to BI or BI/II, and then back to 9. I will appear in the display for the cooking zone and the B booster indicator will light up. To activate Booster II ^ Turn the control past power setting 9 to BI/II, and then back to 9.
Keeping warm Each cooking zone has a keeping warm function. If the keeping warm function has been activated, the cooking zone will switch off automatically after a maximum of 2 hours. This function is for keeping food that has just been cooked warm, i.
– Use a pan lid whenever possible to minimise heat loss. uncovered covered – Select a smaller pan when cooking small quantities. A smaller pan uses less energy than a larger pan with very little in it. – Cook with as little water as possible. – Once food has come to the boil or the pan is hot for frying, reduce the heat to a lower setting.
Safety lock Keep children away from the hob for their own safety. Your appliance is equipped with a safety lock to prevent the hob and cooking zones being switched on. The safety lock can only be activated when the cooking zones are switched off. The control on the right is used to activate and deactivate the lock.
Overheating protection All the induction coils and the cooling element for the electronics are fitted with an overheating protection mechanism. To prevent the induction coils and cooling element from .
Miele offer a range of branded cleaning and conditioning agents for your hob. See "Optional accessories". , Under no circumstances use a steam cleaning appliance to clean this appliance. The steam could reach the electrical components and cause a short circuit.
Ceramic surfaces Do not use washing-up liquid to clean the ceramic surface. Washing-up liquid will not remove all soiling and deposits. It will form an invisible coating which will cause permanent discolouration of the ceramic surface. Clean the hob regularly with a suitable ceramic hob cleaner.
, Installation work and repairs to electrical appliances must only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK). Repairs and other work by unqualified persons could be dangerous.
... after the cooking zone has been switched on for a few seconds L appears in the display. The safety lock has been activated (see "Safety lock"). ... H appears in one of the cooking zone displays. The overheating protection mechanism has been triggered (see "Overheating protection").
Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your appliance. These products can be ordered online: or from Miele (see back cover for contac.
The appliance must only be installed and connected to the electricity supply by a suitably qualified and competent person in strict accordance with current national and local safety regulations. Fit the wall units and extractor hood before fitting the hob to avoid damaging the appliance.
Safety distance above the appliance A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details.
Safety distances to the sides of the appliance Ideally the appliance should be installed with plenty of space on either side. There may be a wall at the rear and a tall unit or wall at one side. On the other side, however, no unit or divider should stand higher than the built-in appliance (see illustrations).
Safety distances underneath the hob To ensure sufficient ventilation to the hob, a minimum gap must be left between the underside of the hob and any oven, interim shelf or drawer. The minimum gap between the underside of the hob and – the top of an oven is 15 mm .
Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.
CS 1212-1 a Spring clamps b Front c Casing depth d Casing depth including mains connection box with mains connection cable, L = 2000 mm Appliance and building-in dimensions 46.
CS 1222 / CS 1221-1 a Spring clamps b Front c Casing depth d Casing depth including mains connection box with mains connection cable, L = 2000 mm Appliance and building-in dimensions 47.
^ Make the worktop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall , as well as from any tall unit or side wall to the right or left of the appliance. See "Safety instructions for installation".
When installing two or more appliances next to each other a spacer bar b must be used between each one. See "Fixing the spring clamps and spacer bars". Worktop cut-out - two appliances Worktop cut-out - three appliances To calculate the cut-out width (D) required: Add up the widths of each appliance (e.
a Spring clamps b Spacer bars c Gap between spacer bar and worktop d Sealing strip The illustration shows a worktop cut-out with spring clamps a and spacer bars b for 3 appliances.
Wooden worktops ^ Position the spring clamps supplied a and spacer bars b on the top edge of the cut-out in the positions marked. ^ Secure the spring clamps and spacer bars with the 3.
Granite and marble worktops The screws are not required for granite or marble worktops. ^ Position and secure the spring clamps a and spacer bars b using strong, double-sided adhesive tape c . ^ Apply silcone to the side edges and the lower edges of the spring clamps a and spacer bars b .
^ Feed the connection cable down through the cut-out. ^ Starting at the front, position the appliance in the worktop cut-out. ^ Using both hands, press down evenly on the sides of the appliance until it clicks into position. When doing this make sure that the seal under the appliance sits flush with the worktop on all sides.
Do not use any sealant unless expressly instructed to do so. The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop. Do not use sealant between the frame of the top part of the appliance and the worktop.
All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK).
Important The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system, which complies with local and national regulations.
In the event of any faults which you cannot remedy yourself, or if the appliance is under guarantee, please contact: – Your Miele dealer, or – the Miele Service Department (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
58.
59.
Alteration rights reserved/ 2911 M.-Nr. 09 055 450 / 02.
Een belangrijk punt na aankoop van elk apparaat Miele CS 1212-1 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Miele CS 1212-1 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Miele CS 1212-1 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Miele CS 1212-1 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Miele CS 1212-1 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Miele CS 1212-1 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Miele CS 1212-1 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Miele CS 1212-1 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
