Gebruiksaanwijzing /service van het product F9122 UI-1 van de fabrikant Miele
Ga naar pagina of 48
Operating and installation instructions Freezer F 9122 Ui-1 To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time.
Guide to the appliance .............................................4 Caring for the environment ..........................................5 Warning and Safety instructions .....................................6 How to save energy ....................
Installation ......................................................3 1 Side-by-side installation .............................................3 1 Location .........................................................3 1 Climate range .....................
a On/Off button b Temperature selector button c Temperature display f Freezer drawers g Ventilation gaps d Super freeze button and indicator light e Alarm off button and indicator light Guide to the a.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and should be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
This appliance complies with all relevant safety requirements. Improper use can, however, present a risk of both personal injury and material damage. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time.
Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Do not install and use a damaged appliance. It could be dangerous. ~ If the connection cable is faulty it must only be replaced by a service technician authorised by the manufacturer to protect the user from danger.
~ The electrical safety of this appliance can only be guaranteed if correctly earthed. It is most important that this basic safety requirement is observed and regularly tested and where there is any doubt, the household wiring system should be inspected by a qualified electrician.
Correct use ~ Never handle frozen food with wet hands. Your hands may freeze to the frozen food. Danger of frost burn. ~ Do not take ice cubes out with your bare hands and never place ice cubes or ice lollies in your mouth straight from the freezer. The very low temperature of the frozen ice or lollies can cause frost burn to the lips and tongue.
~ Never place electric heaters or candles in the appliance to defrost it. These can damage the plastic parts. ~ Do not use defrosting sprays or de-icers, as they might contain substances which could damage the plastic parts or which could cause a build-up of gases and pose a danger to health.
Normal energy consumption Increased energy consumption Installation site In a ventilated room. In an enclosed, unventilated room. Protected from direct sunlight. In direct sunlight. Not near to a heat source (radiator, oven). Near to a heat source (radiator, oven).
Before using for the first time Cleaning ^ Clean the inside of the appliance and the accessories with lukewarm water and a little washing-up liquid, and then dry with a soft cloth.
It is very important to set the correct temperature for storing food in the appliance. Micro-organisms will cause food which is not stored at the correct temperature to deteriorate rapidly. Temperature influences the growth rate of these micro-organisms.
Temperature display The temperature display on the control panel always shows the required temperature. The temperature can be adjusted from: -15 °C to -32 °C The temperature display will flash if .
Your appliance has been fitted with a warning system which ensures that the temperature in the freezer cannot rise unnoticed and to avoid energy being wasted if the door is left open. Activating the alarm system The alarm system is always active. It does not have to be switched on manually.
Switch the Super freeze function on before putting fresh food into the freezer. This helps food to freeze quickly and retain its nutrients, vitamins, flavours and appearance. Super freeze is not necessary: – when putting in food that is already frozen.
Maximum freezing capacity To ensure that fresh food placed in the freezer freezes through to the core as quickly as possible, the maximum freezing capacity must not be exceeded. The maximum freezing capacity for freezing within a 24-hour period is given on the data plate: "Freezing capacity .
Home freezing Only freeze fresh food which is in a good condition. Hints on home freezing – The following types of food are suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, dairy products, pastry, leftovers, egg yolks, egg whites and a range of pre-cooked meals.
Before placing food in the freezer ^ When freezing more than 2 kg of fresh food, switch on the Super freeze function some time before placing the food in the freezer (see "Super freeze"). This helps food that is already in the freezer compartment to stay frozen.
Defrosting Frozen food can be defrosted in different ways: – in a microwave oven, – in an oven using the "Fan" or "Defrost" setting, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep other food cold), – in a steam oven.
In normal use, ice and frost will form in the freezer section, e.g. on the internal walls. How much ice and frost accumulates in the appliance will depend on the following factors: – The appliance door has been opened frequently or left open for a while.
To defrost Carry out the defrosting procedure as quickly as possible if food has not been placed in another freezer. The longer the food is left out at room temperature, the faster it defrosts. Do not use a steam-cleaning appliance to aid the defrosting process.
Make sure that water cannot get into the electronic unit or into the ventilation gaps. Do not use steam cleaning apparatus to clean the appliance. Steam could reach electrical components and cause a short circuit. The data plate located inside the appliance must not be removed.
Ventilation gaps ^ The ventilation gaps should be cleaned regularly with a brush or vacuum cleaner. A build-up of dust will increase the energy consumption of the appliance. Door seal Do not use any oils or grease on the door seal as these will cause the seal to deteriorate and become porous over time.
Repairs to electrical appliances should only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.
. . . food has frozen together. Use a blunt instrument, e.g. a spoon handle or plastic scraper, to prise it apart carefully. . . . there is a thick layer of ice in the freezer. ^ Check whether the door closes properly. ^ Defrost and then clean the freezer.
Normal noises What causes them Brrrrr... Humming noise made by the motor (compressor). This noise can get louder for brief periods when the motor is switching on. Blubb, blubb.... A gurgling noise can be heard when coolant is circulating through the pipes.
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – your Miele Dealer or – Miele (see back cover for contact details). When contacting your Dealer or Miele, please quote the model and serial number of your appliance.
Demo mode The appliance can be demonstrated in the showroom or at exhibitions in "Demo mode". In this mode the controls and interior lighting are functioning but the compressor remains switched off. To activate Demo mode ^ Press the On/Off button.
Electrical connection U.K. All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK). The appliance is supplied with a mains cable and moulded plug ready for connection to an a.
This appliance must be built in, otherwise it could tip up. Side-by-side installation The left side of this appliance has side wall heating making it suitable for installing next to a refrigerator. Each appliance must be built-under into a separate niche.
Ventilation Air at the back of the appliance gets warm. It is very important for the cooling system of the appliance to have adequate ventilation. Ventilation into and out of the appliance is through the appliance plinth. The plinth must not be covered or blocked in any way.
Plinth height B depends on the building under height: With a niche height of 820 mm the plinth height is 100 - 170 mm. The plinth height will be dictated by the height of the furniture front. With a building under height of 870 mm the plinth height is 150 - 220 mm.
The door hinges are set ex-works to enable the doors to be opened wide. However, if the opening angle of the door needs to be limited for any reason, the hinges can be adjusted to accommodate this. For example, if the appliance door hits an adjacent wall when opened, the opening angle can be limited to 90°.
Do not change the door hinging if this appliance is to be installed "side-by-side" with another appliance. Each appliance must be built-under into a separate niche and the freezer must be installed on the right-hand side of the refrigerator.
If you have put locking pins into the hinges to stop the door opening too far: ^ Remove the locking pins from the top of the hinges. To remove the soft-close mechanism ^ Place the door with the outer side downwards on a stable surface. ^ Using a screwdriver, carefully push tension spring a outwards.
To secure the soft-close mechanism ^ Place the door with the outer side downwards on a stable surface. ^ Screw ball joint d of soft-close mechanism c into the new fixing holes. ^ Push tension spring a inwards again. ^ Screw mounting b onto the hinge and tighten securely.
Weight of the furniture door Before fitting a furniture door, ensure that the weight of the door does not exceed the maximum permitted: Appliance Maximum weight of furniture door in kg F 9122 Ui-1 20 Fitting a door front which is heavier than the maximum permitted could damage the hinges.
^ Push the appliance into its building-under niche. ^ Align the appliance so that the front edges of the hinges at the top and bottom are flush with the front edge of the housing unit side wall. This will create a gap all round of 42 mm to the front edges of the housing unit side walls.
Aligning the appliance ^ Hold the plinth facing at the side and pull it forwards and off. With a building-under height of 820 mm the adjustable feet must not be extended. With a building-under height of more than 820 mm the feet must be extended. For example, with a building-under height of 870 mm, the feet must be extended by approx.
The ventilation gaps must not be covered over. If there is a continuous plinth in the kitchen, a ventilation gap will need to be made in the plinth for the appliance: Building-under height Dimension D.
Fitting a furniture door Ensure that the plinth facing is replaced correctly. ^ Using a screwdriver, carefully push tension spring a outwards. Warning. The soft-close mechanism snaps shut when dismantled. Danger of injury. ^ Unscrew mounting b and pull soft-close mechanism c downwards to remove it.
^ Using a pencil, lightly mark a line down the centre of the inside of the furniture door. ^ Hang the fixing bracket with fitting aids a onto the inside of the furniture door. Align the fixing bracket centrally. ^ Attach the fixing bracket securely using at least 6 shor t4x1 4m m chipboard screws b .
^ Whilst counterholding adjusting bolts b with a screwdriver, tighten nuts a at the top of the appliance door. ^ Attach the appliance door and the furniture door using screws through fixing brackets a : – Drill holes in the furniture door (mark the position of the holes first).
^ Push tension spring a inwards again. ^ Screw mounting b onto the hinge and tighten securely. ^ Open out soft-close mechanism c and hook it onto ball joint d . ^ Place the cover in position. To make sure the appliance is correctly fitted: – The door must close properly.
46.
47.
Alteration rights reserved / 5111 F 9122 Ui-1 M.-Nr. 09 265 210 / 01.
Een belangrijk punt na aankoop van elk apparaat Miele F9122 UI-1 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Miele F9122 UI-1 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Miele F9122 UI-1 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Miele F9122 UI-1 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Miele F9122 UI-1 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Miele F9122 UI-1 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Miele F9122 UI-1 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Miele F9122 UI-1 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
