Gebruiksaanwijzing /service van het product G 5570 SCVi van de fabrikant Miele
Ga naar pagina of 76
Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time.
Guide to the appliance .............................................5 Appliance overview .................................................5 Control panel ......................................................6 Warning and Safety instructions .........
Operation .......................................................3 1 Detergent ........................................................3 1 Adding detergent ..................................................3 2 Switching on ............................
Programme chart .................................................5 6 After sales service ................................................6 0 Repairs .......................................................6 0 Future updates ............................
Appliance overview a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Filter combinat.
Control panel a Display b Delay start button , with indicator light c Turbo button with indicator light d Intensive lower basket button with indicator light e Programmes f Programme selector button g On/Off button K with indicator light h In-operation indicator light This instruction book applies to several different dishwasher models.
This appliance conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time.
~ Keep children away from detergents. Dishwasher detergents contain irritant and corrosive ingredients which can cause burning in the mouth, nose and throat if swallowed, or inhibit breathing. Keep children away from the dishwasher when the door is open.
~ The appliance must not be used in a non-stationary location (e.g. on a ship). ~ Do not install the dishwasher in a room where there is a risk of frost. Frozen hoses may burst or split. The reliability of the electronic control unit may be impaired at temperatures below freezing point.
Installation ~ The dishwasher must be installed and connected in compliance with the diagram supplied. ~ The dishwasher must be correctly aligned to ensure problem-free operation. ~ In order to ensure stability, built-under and integrated dishwashers must only be installed under a continuous worktop which is secured to adjacent cabinetry.
~ Inadvertently filling the salt reservoir with powder or liquid dishwasher detergent will damage the water softener. Make sure you have picked up the correct packet of dishwasher salt before filling .
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children.
Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your water supply is suitable, this dishwasher can be connected to hot water for further economies.
To open the door ^ Pull the handle. If the door is opened during operation all functions are automatically interrupted. To close the door ^ Push the baskets right in.
Display General The display is used to select or set the following: – the programme – extras – the delay start time – settings During a programme, the display shows the following: – the stag.
Basic settings ^ Switch the dishwasher on with the On/Off button K . If the dishwasher is being switched on for the first time, the welcome screen will appear. Language The display will then change automatically to the screen for setting the language.
Before using the appliance for the first time, you require: – approx. 2 litres of water, – approx. 2 kg dishwasher salt*, – domestic dishwasher detergent*, – rinse aid* formulated for domestic dishwashers. *See "Optional accessories".
Important: Before filling the salt reservoir with dishwasher salt for the first time , you must fill it with approx. 2 litres of water to enable the salt to dissolve. Once the dishwasher has been used, there is always sufficient water in the reservoir.
"Replenish salt" message ^ Fill the salt reservoir with dishwasher salt for reactivation when the F Replenish salt message appears. (If it appears during a programme, wait until the end of the programme). ^ Confirm by pressing the middle button.
Rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically.
^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. ^ Close the flap firmly so that it clicks into place. Otherwise water can enter the rinse aid reservoir during a programme. ^ Wipe up any spilled rinse aid.
Note Remove coarse food residues from crockery. There is no need to rinse items under running water. , Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher.
Items not suitable for dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher.
Upper basket , For safety reasons, do not operate the dishwasher without the upper and lower baskets in place (except when running the Tall items 65 °C programme, if available). ^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc.
Jumbo cup rack (depending on model) The cup rack can be set at two different widths so that it can also accommodate large cups. ^ Pull the cup rack upwards and click it back into position at the required width. Glass rail This rail is designed to hold tall glasses and glasses with stems securely.
Adjusting the upper basket In order to gain more space for taller pieces of crockery in the lower or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low.
Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Glasses, cups and small items such as saucers can also be placed in the lower basket.
MultiComfort area The rear section of the lower basket is used for washing cups, glasses, plates, pots and pans. ^ The glass rack can be raised to make more room for tall items. ^ Stem glassware, e.g. wine glasses or champagne flutes, can be leaned against the glass rack or suspended from it.
Cutlery 3D cutlery tray (depending on model) ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Cutlery basket (depending on model) The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket. ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier.
Detergent , Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid. Active ingredients Modern detergents contain various active ingredients, the most important of which are: – Phosphates to prevent calcification. – Alkalis to aid removal of dried on soiling.
, Avoid inhalation of powder detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Consult a doctor immediately if detergent has been swallowed or inhaled.
Switching on ^ Open the stopcock, if it is closed. ^ Open the door. ^ Make sure the spray arms are not obstructed. ^ Switch the dishwasher on with the On/Off button K . One of the programmes will appear in the display and the appropriate indicator light will come on.
Display The duration of the programme selected appears in hours and minutes in the display before the programme begins. During the programme, the time left until the end of the programme is displayed.
At the end of the programme At the end of a programme, the In-operation indicator light will be visible flashing slowly with the door shut. After the door is opened, O Finished will appear in the display. The drying fan will continue to run for a few minutes at the end of the Quick wash programme.
Interrupting a programme A programme is interrupted as soon as the door is opened. If the door is closed again, the programme will continue from the point it was at before the door was opened. , Water in the dishwasher may be hot. Danger of scalding. Only open the door if absolutely necessary and exercise extreme caution when doing so.
Intensive lower basket The Intensive lower basket additional function allows you to wash heavily soiled items in the lower basket while washing more delicate items in the upper basket. Cleaning perfomance in the lower basket is intensified in programmes where this function is available.
Delay start The start time of a programme can be delayed, e.g. to benefit from economy rates of electricity. A delay start time of between 30 minutes and 24 hours can be selected. The delay start time is set in 30 minute steps. When using the Delay start function, make sure that the detergent compartment is dry before adding detergent.
Starting a programme before the Delay start period has elapsed: A programme can be started before the Delay start period has elapsed. Proceed as follows: ^ Open the door. ^ Switch the dishwasher off using the On/Off button K . ^ Switch the dishwasher on again with the On/Off button K .
Check your dishwasher regularly (approx. ever y4-6 months). This way faults and problems can be avoided. , The external surfaces of the dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the external surfaces.
Cleaning the control panel and door front , Remove any soiling immediately. If this is not done, it might become impossible to remove and could cause the external surfaces to alter or discolour. ^ The control panel should only be wiped with a damp cloth.
Checking the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. , This dishwasher must not be used without all the filters in place.
To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b . ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages. ^ Replace the filter combination so that it lies flat in the base of the wash cabinet.
Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one).
With the help of the following guide, minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Service Department.
Problem Possible cause Remedy The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following messages appears in the display: Before rectifying the problem: – Switch the dishwasher off using the On/Off button K . ; Fault FXX There may be a technical fault.
Water inlet/drain fault Problem Possible cause Remedy The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following messages appears in the display: 2 Open stopcock The stopcock is closed. Open the stopcock fully. 2 Inlet Before rectifying the problem: – Switch the dishwasher off using the On/Off button K .
Problem Possible cause Remedy The In-operation indicator is flashing quickly. The buzzer is sounding. The following message appears in the display: 2 Drain Before rectifying the problem: – Switch the dishwasher off using the On/Off button K . The water outlet is restricted, water remains in the wash cabinet at the end of a programme.
General problems Problem Possible cause Remedy The indicators and display are dark. Only the On/Off indicator K is flashing slowly. The indicators and display have switched off automatically to save energy (Standby mode). Press the On/Off button K . This switches Standby off.
Noises Problem Possible cause Remedy Knocking noise in the wash cabinet. A spray arm is knocking against an item in a basket. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the wash cabinet. Items of crockery are insecure in the wash cabinet.
Unsatisfactory washing result Problem Possible cause Remedy The dishes are not clean. The dishes were not loaded correctly. See notes in "Loading the dishwasher". The programme was not powerful enough. Select a more intensive programme. See Programme chart.
Problem Possible cause Remedy Dishes, cutlery and glasses are not dry or are flecked. The amount of rinse aid may be insufficient, or the rinse aid reservoir empty. Replenish the reservoir, increase the dosage or change the brand of rinse aid (see "Before using for the first time: Rinse aid").
Problem Possible cause Remedy Glassware has a brown or blue tinge, and film cannot be wiped off. This may be caused by the detergent. Change your detergent. Glassware is dull and discoloured; film cannot be wiped off. The glasses are not dishwasher-proof.
Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet. , The plastic housing of the water connection contains an electrical component.
Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug.
Crockery Food deposits Action required Mixed, everyday crockery All normal food deposits This needs an adaptable programme... Shorter duration... Heat-sensitive glasses and plastic Fresh, easily removed food deposits This needs a short programme... Mixed crockery This needs a gentle programme with glass care.
Programme Detergent Compartment I 2) Compartment II 2) Sensor wash – 25 ml or 1 tab + Turbo option Quick wash 40°C – 25 ml or 1 tab 3) Sensor wash gentle – 25 ml or 1 tab Light soiling 50°C .
Programme Programme sequence Pre-wash Main wash °C Interim rinse Final rinse °C Drying 12 Sensor wash Variable programme sequence, sensor controlled adjustment according to the amount of crockery an.
Consumption 1) Duration 1) Electricity Water Cold water connection (15 °C) kWh Hot water connection (55 °C) kWh Litres Cold water connection (15 °C) h:min Hot water connection (55 °C) h:min 0.95-1.35 0.70-1.00 10.0-17.0 1:36-2:38 1:23-2:21 0.60 0.
Repairs In the event of any faults that you cannot remedy yourself, please contact: – Your Miele dealer, or – the Miele Service Department (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer, from the Miele Spare Parts Department or via the Internet at www.miele-shop.com (some may be supplied as standard, depending on model).
Electrical connection U.K. , All electrical work must be carried out by a suitably qualified and competent person, in accordance with current local and national safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out.
The Miele waterproof anti-leak system Providing your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. Connection to the water supply , Water in the dishwasher must not be used as drinking water.
– The water pressure (flow pressure at the take-off point) must be between 30 and 1000 kPa (0.3 and 10 bar). If the water pressure is lower than this, the fault message Water inlet fault will appear in the display (see Problem solving guide). If the water pressure is too high, a pressure reducer valve must be fitted.
Drainage – The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. – The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm.
Dishwasher model Standard XXL Height 80.5 cm (adjustable + 6.5 cm) 84.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) Width 59.8 cm 59.8 cm Width of building-in recess 60 cm 60 cm Depth 57 cm 57 cm Weight Max.
Settings menu for changing standard settings To open the Settings menu ^ Switch the dishwasher off with the On/Off button K , if it is switched on. ^ Press and hold the Programme selector button in. ^ Switch on the dishwasher with the On/Off button K and keep the Programme selector button pressed in for at least 4 seconds.
Water hardness Your dishwasher is fitted with a water softener which you need to programme to the water hardness level in your area. – Your local water authority will be able to advise you of the water hardness level in your area. – Where the water hardness fluctuates e.
Rinse aid You can adjust the rinse aid dosage for best results. The rinse aid dosage can be set from approx. 0-6 ml. The factory default setting is 3 ml. If the function to adjust the Sensor wash programme has been activated, the amount of rinse aid dispensed in the Sensor wash programme can be higher than that set.
Sensor wash You can adjust the Sensor wash programme so that it will remove stubborn soiling in a lightly soiled load. ^ Select the setting you want, and confirm your selection with the middle button. Memory You can use the Memory function to save the last programme selected.
Replenish salt and rinse aid reminders If you only ever use combination products containing salt and rinse aid in your dishwasher, you can switch both of these reminders off if you wish. The DetergentAgent function will not be affected by this. ^ Select the setting you want, and confirm your selection with the middle button.
Contrast There are seven different display contrast settings. ^ Select the contrast setting you want and confirm your selection with the middle button. Check filters You can adjust the interval at which the reminder to check the filters appears. You can set an interval of between 30 and 60 programme cycles.
73.
74.
75.
Alteration rights reserved/ G5570/G5575 / 1212 M.-Nr. 09 255 880 / 00.
Een belangrijk punt na aankoop van elk apparaat Miele G 5570 SCVi (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Miele G 5570 SCVi heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Miele G 5570 SCVi vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Miele G 5570 SCVi leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Miele G 5570 SCVi krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Miele G 5570 SCVi bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Miele G 5570 SCVi kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Miele G 5570 SCVi . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
