Gebruiksaanwijzing /service van het product KM 390 G / KM 391 G van de fabrikant Miele
Ga naar pagina of 32
Installation instructions Gas hobs K M3 7 0G/K M 370-1 G KM 371 G K M3 9 0G/K M3 9 1G To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time.
G This appliance can be used in countries other than those specified on the appliance. It is, however, set up for connection to the gas and electricity supplies in the countries specified. For use in other countries please contact the Miele spare parts or customer service department in your country.
Gas-heated appliances Safety precautions to take if you smell gas ß Turn off the gas emergency control valve immediately. This is usually located near the gas meter. ß Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches.
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Appliance dimensions and worktop cut-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 K M3 7 0 .......................
Building in Fit wall units and extractor hood before fitting the hob, to avoid damaging the appliance. ~ The veneer or laminate coating of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort.
~ The room in which the gas hob is installed must be at least 20 m 3 in size with a door or window in it which can be opened to the outside air. ~ Using the gas hob will cause a build-up of heat and moisture in the room in which it is installed. Ensure that the room has sufficient natural or mechanical means of ventilation, e.
KM 370 a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 7.
KM 370-1 G a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 8.
KM 371 a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 9.
KM 390 a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 10.
KM 391 a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 11.
^ Prepare the worktop cut-out as shown in the diagram. Remember to maintain a minimum safety distance of 50 mm between the hob and the back wall and 150 mm between it and a side wall or tall unit to the right or left of the hob. (See "Warning and Safety instructions").
Building in the appliance ^ Feed the electricity connection cable through the cut-out and connect. ^ Place the gas hob in the prepared cut-out. ^ Make the gas connection (see relevant section). Securing the appliance KM 371 G / KM 391 G ^ Secure the gas hob at the front and rear with fixing brackets a supplied as shown.
Do not let sealant get in between the hob frame and the worktop. This could cause difficulties if the hob ever needs to be taken out for servicing and possibly result in damage to the hob frame or the worktop. The sealing strip under the edge of the top part of the hob provides a sufficient seal for the worktop.
All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current local and national safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous.
Important The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system, which complies with current local and national safety regulations.
Connection to the gas supply, or conversion from one type of gas to another should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations, (e.g. Corgi registered in the U.
a Connection with test point specifically for GB b Connection with test point specifically for GB and 90° angle Natural gas / liquid gas ^ The appliance is supplied with an R 1/2" - ISO 7-1 (DIN 2999) gas connection point. ^ An appropriate rigid connection and isolating valve must be installed for final connection.
Nominal rating for all gas types with the burner full on Burner Gas type KM 370 G / KM 370-1 G / KM 371 G KM 390 G / KM 391 G kW g/h kW g/h Small burner Natural gas H Liquid gas 1.00 1.00 - 73 1.00 1.00 - 73 Normal burner Natural gas H Liquid gas 1.75 1.
KM 370 G / KM 370-1 G / KM 371 G When converting to anothe type of gas, the main jets and the small jets on all burners have to be changed. Screw in the new jets according to the following table. For U.K. and IE Main jet Ø Small jet Ø Natural gas H Small burner Medium burner Large burner Wok 0.
Changing the jets Disconnect the gas hob from the electricity supply by switching off at the socket and withdrawing the plug or by removing the mains fuse. Changing the main jets Small, medium and large burners ^ Take off the pan support, burner cap b and the burner head d .
Wok burner ^ Take off the burner cap a , burner ring b and burner head c . ^ Loosen screws d and remove the cover plate. ^ Using an M7 socket spanner unscrew the main jets e (larger diameter jet) and f (smaller diameter jet).
Changing the small jets (for all burners) To change the small jets, the burner securing screws must first be loosened and the upper section of the appliance removed. ^ Remove the operating controls by pulling them upwards. ^ Remove the upper section. N.
After changing the jets ^ Assemble the removed burner parts in reverse order and check for leaks by operating the burner without the upper section of the hob in place (use a match to ignite the flame). ^ Remove the burner parts again. ^ Then replace the upper section of the hob.
KM 390 G / KM 391 G When converting to another type of gas, the main jets and the small jets on all burner have to be changed. Screw in the new jets according to the following table. For U.K. and IE Main jet Ø Small jet Ø Natural gas H Small burner Medium burner Large burner Wok 0.
Changing the jets Disconnect the gas hob from the electricity supply by switching off at the socket and withdrawing the plug or by removing the mains fuse. Changing the main jets Small, medium and large burners ^ Take off the pan support, burner cap b and the burner head d .
Wok burner ^ Take off the burner cap a , burner ring b and the burner head c . ^ Loosen screws d and remove the cover plate. ^ Using an M7 socket spanner unscrew the main jets e (larger diameter) and f (smaller diameter).
Changing the small jets To change the small jets, the burner securing screws must first be loosened and the upper section of the appliance removed. ^ Remove the operating controls by pulling them upwards.
Wok burner b Small jet with smaller diameter (e.g. for liquid gas: 0.20). c Small jet with larger diameter (e.g. for liquid gas: 0.46). ^ Remove the ignitor a . ^ Using a small screwdriver, unscrew the small jets b and c in the gas fitting. ^ Pull the jets out with a pair of pointed pliers.
After changing the jets ^ Assemble the removed burner parts in reverse order and check for leaks by operating the burner without the upper section of the hob in place (use a match to ignite the flame). ^ Remove the burner parts again. ^ Then replace the upper section of the hob.
31.
Alteration rights reserved / 3209 M.-Nr. 05 827 720 / 10.
Een belangrijk punt na aankoop van elk apparaat Miele KM 390 G / KM 391 G (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Miele KM 390 G / KM 391 G heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Miele KM 390 G / KM 391 G vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Miele KM 390 G / KM 391 G leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Miele KM 390 G / KM 391 G krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Miele KM 390 G / KM 391 G bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Miele KM 390 G / KM 391 G kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Miele KM 390 G / KM 391 G . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
