Gebruiksaanwijzing /service van het product WT 2780 WPM van de fabrikant Miele
Ga naar pagina of 88
Operating instructions Washer-dryer WT 2780 WPM To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed safely and kept out of the reach of babies and young children.
Caring for the environment ..........................................2 Warning and Safety instructions .....................................6 Guide to the machine .............................................1 4 Control panel .........................
Extra options .....................................................3 9 Low temperature ................................................3 9 Thermospin ....................................................3 9 Extra quiet .................................
Installation surface .................................................6 8 Installing the washer-dryer ..........................................6 8 Removing the transit bars ...........................................6 8 Levelling the machine ........
~ It is essential to read the operating instructions. This washer-dryer conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the washer-dryer, please read these instructions carefully before using it for the first time.
~ The washer-dryer is not intended for outdoor use. ~ The washer-dryer can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised whilst using it, or have been shown how to use it in a safe way and understand the hazards involved.
Technical safety ~ Before setting up the washer-dryer, check it for any externally visible damage. Do not install or use a damaged machine. ~ Before connecting the washer-dryer, ensure that the connection data on the data plate (voltage and connected load) match the mains electricity supply.
~ The washer-dryer must be isolated from the electricity supply in the event of a fault and during installation, maintenance and repair work. ~ The Miele "Water protection system" protects f.
Correct use ~ Do not install your washer-dryer in rooms where temperatures below freezing may occur. Frozen hoses may burst or split. The reliability of the electronic control unit may be impaired at temperatures below freezing point.
~ To prevent the risk of fire, the following must not be dried in this washer-dryer: – items which have not been washed. – items, such as workwear, which have not been thoroughly cleaned and which are still soiled with grease, oil or other deposits (such as cosmetics, lotions etc).
~ In many programmes, the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them (this also avoids the danger of the laundry self-igniting). The programme is not finished until the cooling down phase has been completed.
~ Do not use solvent based cleaning agents, e.g. those containing benzine, in this washer-dryer, as this may result in damage to component parts and create toxic fumes. Such agents also pose a fire and explosion hazard. ~ Caution, the metal cap is hot after drying.
Control panel a Start/Stop button For starting the programme selected and cancelling a programme once it has started. b Display with X , OK and Y buttons See the following page for more information. c + button For selecting delay start. d PC / Optical interface This is used by Miele service technicians during servicing work for testing purposes.
Display The display is operated using the X , OK and Y buttons. The value or option currently selected will appear highlighted. Press button X to decrease a value in the display or to scroll down to the next option. Press button Y to increase a value in the display or to scroll up to the next option.
Before using the machine for the first time ensure that it is correctly installed and connected. Also check that the drain filter is securely tightened to prevent the risk of water leakage during use.
Running your first programme Your washer-dryer is now ready for the first programme to be run. ^ Turn the programme selector to Cottons . ^ Press the Start/Stop button. ^ At the end of the programme switch the machine off. After running the first programme, the load sensor has to be calibrated to zero (as you would with bathroom scales).
Energy and water consumption – Water consumption and energy usage are determined by the size of the load. To make the most out of your machine, load the maximum amount for the programme you are using. – Use the Automatic plus and Express 20 programmes for small loads.
Short instructions The headings numbered A , B , C ,... show the operating sequence and can be used as brief instructions. Separate washing A Sort the laundry ^ Empty all pockets. , Foreign objects (e.g. nails, coins, paper clips, etc.) can cause damage to textiles and to components in the machine.
B Switch the machine on The interior drum lighting will come on. The drum lighting will go out automatically after five minutes. Press the Door button to switch the drum lighting back on again. C Select a programme ^ Select the programme you want. The programme selected will appear in the display.
D Select Extra option(s) ^ Press the appropriate button to select Short or Water plus . The relevant indicator light will come on. ^ Then select any Further extras or the Stains option: Example: Furth.
F Add detergent The detergent dispenser display will now appear. Detergent 7 100% The percentage shown relates to the amount of detergent recommended by the manufacturer on the packaging. 40% Add slightly less than half the recommended amoun t... 50% Add half the recommended amoun t.
G Select Delay start If required please refer to "Delay start" for more information. H Start the programme ^ Press the flashing Start/Stop button. The estimated programme duration will start counting down in one minute steps. During the first few minutes the machine measures how much water is being absorbed by the laundry.
Extra options You can use the Extra option buttons to augment the basic wash programmes. Short For light to nomal soiling with no visible staining. The duration of the main wash is reduced. Water plus The water level in the main wash and the rinses will be increased.
Extra rinse This extra option introduces an extra rinse. Pre-wash For laundry with large amounts of dirt (e.g. dust, sand). Soak For heavily soiled items with protein stains. A length of time of between 30 minutes and 6 hours can be chosen, in 30 minute periods, for the "Soak" process.
Final spin speed Programme rpm Cottons 1600 Minimum iron 1200 Denim 900 Woollens 1200 Express 20 1600 Shirts 600 Automatic plus 1200 Dark garments 1200 Delicates 600 Sportswear 1200 Trainers 1000 Oute.
Programme chart Cottons 9ö8E76 * cold to 95°C Max. load 5.5 kg Suitable for Cotton, linen or cotton mix fabrics, e.g. T-shirts, underwear, table linen.
Automatic plus 7621 * cold to 40°C Max. load 4.5 kg Suitable for Mixed loads of garments suitable for the Cottons and Minimum iron programmes. Sort according to colour. Note The wash parameters are adjusted automatically in this programme to ensure the best possible care and wash results for each item.
Outerwear cold to 40°C Max. load 2.0 kg Suitable for Outerwear made from membrane fabrics such as Gore-Tex ® , SYMPATEX ® , WINDSTOPPER ® etc. Note – Zip up jackets before washing. – Do not use fabric conditioner. Extra options Short, Water plus, Stains, Extra quiet, Extra rinse, Pre-wash, Soak, Rinse hold Proofing 40°C Max.
Silks / cold to 30°C Max. load 1.0 kg Suitable for Silks and other handwashable fabrics with no wool content Note Place socks, tights, bras etc. in a washing bag. Extras Water plus, Extra rinse, Rinse hold Pillows cold to 95°C 2 pillows (40x80 cm) or 1 pillow (80x80 cm) Suitable for Washable pillows with feather, down or synthetic fillings.
Programme sequence Main wash Rinses Spin Water level Wash rhythm Water level Rinses Interim spin Final spin Cottons d a ( 2-4 1)2) LL Minimum iron ( c e 2-3 3) LL Denim ( c e 3 – L Woollens e f e 2 .
d = Low water level ( = Medium water level e = High water level a = Intensive rhythm b = Normal rhythm c = Gentle rhythm d = Sensitive rhythm e = Ultra sensitive rhythm f = Handwash rhythm This machine has fully electronic controls with automatic load recognition.
Detergent Universal detergent Detergent for coloureds Detergent for delicates Specialist detergent Proofing agent Fabric con- ditioner Cottons X X – – – X Minimum iron X X – – – X Denim 1).
All modern detergents produced for automatic washing machines are suitable. Use dispensing aids, e.g. balls, if these are supplied with the detergent. Tablets are suitable for full loads, but note that it may be impractical to reduce tablets for smaller loads.
Fabric conditioner and liquid starch Fabric conditioners make garments soft to handle and help prevent static cling when tumble drying. Starch stiffens and gives body to items of laundry, e.
Separate drying The separate drying programme must be used if the load in the wash programme is greater than the maximum load permitted for drying, or if you only want to dry part of the load that was washed.
B Switch the washer-dryer on C Select a programme ^ Select the drying programme you want. The programme selected will appear in the display. Cottons 60°C 1600 rpm Duration: 2:39 h Further programmes: Turn the programme selector to Further programmes/Settings to display a list of other programmes that the machine has to offer.
D Load the drum ^ Open the drum door. ^ Load the laundry loosely into the drum. See the drying programme chart for maximum loads. Overloading can cause unnecessary wear and tear to the laundry and give a disappointing drying result. E Close the drum door.
Extra options Low temperature The temperature is reduced during the drying programme. For all delicate or minimum iron fabrics with the r symbol on the care label (e.g. acrylic garments). The thermospin is not carried out when the Low temperature extra option has been selected.
Adding or removing laundry after a programme has started ^ Press the Door button to open the drum door. , Do not touch the metal cap located on the inside of the door glass or the back of the drum when adding or removing items. They could be very hot - Danger of burning .
Programme chart Cottons Max. load 3.0 kg* Extra dry, Normal+, Normal** Suitable for Single and multi-layered cotton fabrics such as T-shirts, underwear, towelling, flannelette bed linen. Note Do not use Extra dry for loopknit fabrics as they have a tendency to shrink.
Express 20 Max. load 3.0 kg* Extra dry, Normal+, Normal, Hand iron r , Hand iron rr , Machine iron, Smoothing+ 1) , Timed drying 2) Suitable for Fabrics which can tolerate high temperatures and which can be dried using the Cottons programme.
Smoothing Max. load 3.0 kg* Suitable for Cotton and linen fabrics. Minimum iron items made of mixed fibres, cotton or synthetic fabrics Note – Garments are dampened before the programme starts to help reduce creasing. – They are not completely dried in this programme to make them easier to iron.
Sportswear Max. load 2.0 kg* Normal+, Normal, Hand iron r , Smoothing+ 1) , Timed drying 2) Suitable for Sportswear that is suitable for tumble drying Extras Thermospin, Extra quiet Trainers Max. 2 pairs of shoes Timed drying 2) Suitable for Trainers, specified as machine-washable by the manufacturer.
Hygiene Max. load 3.0 kg* Normal Suitable for Cottons and linen fabrics which are in direct contact with the skin, e.g. underwear, nappies, towelling, bed linen, pillow and mattress covers. Important Because the temperature is held for longer the laundry will feel drier.
1) Smoothing+ : Garments are dampened before the programme starts to help reduce creasing. Textiles are not completely dried in this programme to make them easier to iron. The drying temperature is determined by the programme being used. 2) Timed drying : Timed dring is particularly suitable for small loads and for drying individual items.
Washing and drying in a continuous sequence Where the amount of laundry to be washed and dried in one programme does not exceed the maximum weight permitted for the drying programme, washing and drying in one continuous sequence is recommended.
D Load the drum ^ Open the drum door and load the laundry loosely in the drum. Follow the load size indicator and do not overload. Do not use detergent dispensing aids, e.g. plastic dispenser balls, for washing followed immediately by the drying programme.
The fluff which occurs during drying can collect in the drum and also in the suds container. Run the Rinse out fluff programme before the machine is used again so that fluff cannot be deposited on the next load (e.g. fluff from dark garments being deposited on lighter coloured items) or cause a blockage.
To cancel a programme You can cancel a programme at any time after it has started. ^ Press the Start/Stop button and select Cancel programme or turn the programme selector to Stop . ... During washing: The suds will be pumped away and the washing programme is cancelled.
Changing the spin speed You can change the spin speed up until the final spin begins. You can change the thermospin speed up until the thermospin begins. Altering the drying level / drying time You can alter the drying level or drying time during the washing programme but not once the drying programme has started.
With delay start you can choose when you want the programme to end. The start of a programme can be delayed from 30 minutes up to a maximum of 24 hours, The current time of day needs to have been set for Delay start to work correctly. Select Delay start ^ Select the programme you want and then press the + button.
, Disconnect the machine from the electricity supply by switching off at the wall socket and withdrawing the plug before any cleaning and maintenance work. A range of Miele branded cleaning and conditioning agents is available to order from the Miele Spare Parts Department, or via the internet on www.
^ Clean the siphon. 1 . Remove the siphon from compartment § and rinse under hot running water. Clean the siphon tube in the same way. 2 . Replace the siphon. If starching frequently, thoroughly clean the siphon and siphon tube regularly. A build-up of starch will cause them to get clogged.
Cleaning the porthole glass ^ From time to time you should also clean ... – the door glass on the inside using a mild detergent or soap and water. – the metal cap on the inside of the door glass with a suitable proprietary stainless steel cleaning agent following the manufacturer's instructions on the packaging.
With the help of the following notes, minor faults in the performance of this machine, some of which may result from incorrect operation, can be put right without contacting the Service Department.
A fault message appears in the display Message Possible cause Remedy A 2 Fault Check drainage system – The water outlet is blocked or restricted. – The drain hose has been fixed too high.
Problems with the load size indicator Problem Possible cause Remedy The display indicates a load of <25% or no load size is indicated when the drum is full. Laundry was left in the drum when the machine was switched off. This has decalibrated the sensor from the zero setting.
General problems Problem Possible cause Remedy The machine shakes during the spin cycle. The machine feet are not level. Level the machine (see "Installation and connection"). The pump makes strange noises. This is not a fault. These noises occur at the end of a pump sequence as a normal part of operation.
An unsatisfactory wash result Problem Possible cause Remedy Liquid detergent does not give the required result. Liquid detergents usually contain no bleaching agents. They do not remove fruit, coffee and tea stains. – Use a general purpose detergent containing a bleaching agent.
An unsatisfactory drying result Problem Possible cause Remedy The laundry is still damp after a drying cycle. The load was too small for the electronics to assess the residual moisture correctly. In future dry small loads in a timed drying programme. The laundry has formed a ring in the drum during the spin because it was distributed unevenly.
The drum door cannot be opened by pressing the Door button Problem Remedy The machine is not connected to the electricity supply and / or is not switched on. Insert the plug in the socket and switch on and / or switch the machine on with the K button.
Opening the drum door in the event of a blocked drain outlet and/or power failure ^ Switch the machine off. There is a lever behind the detergent drawer fascia panel. ^ Remove the lever. ^ Use it to open the access flap. Blocked drain outlet If the drain outlet is blocked, up to 25 litres of water will be retained in the machine.
Once the flow of water ceases: ^ Remove the drain filter completely. ^ Clean it thoroughly. ^ Remove any foreign objects (e.g. buttons, coins, etc.) and fluff from the filter housing. Turn the impeller by hand to check that it rotates freely. ^ Put the drain filter back in place and secure.
In the event of any faults which you cannot remedy yourself, please contact: – your Miele dealer, or – the Miele Service Department (see back cover for contact details).
Front view a Inlet hose (with flexible, waterproof metallic outer sleeve) b Electricity supply cable c - f Flexible drain hose (with detachable swivel elbow) g Control panel h Detergent dispenser draw.
Rear view a Protruding lid for holding when moving the machine b Electricity supply cable c Transit bar covers d Inlet hose (with flexible, waterproof metallic outer sleeve) e Drain hose Installation .
Installation surface A concrete floor is the most suitable installation surface, being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface. Please note the following points: ^ The machine must be level and securely positioned.
^ Using the spanner supplied turn the left-hand transit bar 90°, then ^ withdraw the transit bar. ^ Turn the right-hand transit bar 90°, then ^ withdraw the transit bar.
, To avoid the risk of injury the holes for the transit bars must be covered after the transit bars have been removed. ^ Fit the covers on to the two holes. Then plug the holes as shown with the caps. , The machine must not be moved without the transit bars in place.
Screwing out and adjusting the feet The four adjustable screw feet are used to level the machine. All four feet are screwed in when the machine is delivered. ^ Using the spanner supplied turn counter nut 2 in a clockwise direction. Then turn counter nut 2 together with foot 1 to unscrew.
The Miele water protection system The Miele water protection system protects machine from water damage. The system consists of three main components: 1) the inlet hose 2) the electronic unit and the machine housing 3) the drain hose 1) Inlet hose – The inlet hose is tested to withstand pressure of more than 14,000 kPa.
Connection to the water supply The machine should be connected to a mains water supply in accordance with local and national safety regulations. The German authorities do not require it to have a non-return valve as the washer-dryer has been designed to comply with DIN regulations.
Connection to the drainage system The machine drains via a drain pump with a delivery head of 1 metre*. The drain hose must not be kinked as this restricts drainage. The swivel elbow at the end of the hose can be turned in either direction, or can be detached if required, with a sharp twist and pull.
Electrical connection U.K. All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current national and local safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out.
Load Consumption data Energy Water Duration in kWh in litres Short Normal Washing Cottons 95°C 5.5 kg 1.75 45 2 h 19 min 60°C 1) 5.5 kg 0.85 45 2 h 39 min 60°C 3.0 kg 0.63 39 1 h 29 min 40°C 1) 5.5 kg 0.65 57 2 h 19 min 40°C 1) 3.0 kg 0.48 39 1 h 10 min Minimum iron 40°C 1) 3.
Height 850 mm Width 595 mm Depth 580 mm Depth with door open 975 mm Height for building under 820 mm Width for building under 600 mm Depth for building under 600 mm Weight 101 kg Capacity - Washing Capacity - Drying 5.
The Settings menu is used to alter the machine's electronics to suit changing requirements. Settings can be altered at any time. To open the Settings menu ^ Switch the machine on.
Time Select either a 24 hour or 12 hour clock, and then set the current time of day. Clock format ^ Use the X or Y buttons to select the way you want the time to be displayed and confirm your choice with the OK button. Set the time of day ^ Set the hour with the X and Y buttons and confirm your setting by pressing the OK button.
Lock code The code prevents the machine being used without your knowledge. When the code has been activated, you have to enter a code after switching the machine on. Otherwise it cannot be operated. To activate the lock code Lock code Activate Back # ^ Select Activate and confirm your selection.
Longer pre-wash Cottons The pre-wash duration can be extended in the Cottons programme. If you require a longer pre-wash, an additional 6, 9 or 12 minutes can be added to the standard 25 minutes . Gentle action Activating gentle action reduces the drum action and is suitable for washing slightly soiled items more gently.
Drying levels The drying levels in the Cottons and Minimum iron programmes can be altered. Select the required setting and then determine whether laundry should be damper or drier after drying. Extended cool down The cooling down phase which takes place before the end of a programme can be lengthened if required.
Miele offer perfect care for your laundry with a wide range of special programmes designed to suit the fabrics being washed and dried. Miele have also developed a range of specialist CareCollection detergents and conditioning products to offer you a complete package for cleaning and caring for your laundry.
UltraWhite detergent This multi-purpose powder detergent has excellent stain removal properties and is suitable for white and light coloured laundry as well as heavily soiled coloured items. UltraColor detergent for coloured garments This liquid detergent is particularly suitable for cleaning coloured and dark garments.
85.
86.
87.
Alteration rights reserved/4412 M.-Nr. 09 442 060 / 00.
Een belangrijk punt na aankoop van elk apparaat Miele WT 2780 WPM (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Miele WT 2780 WPM heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Miele WT 2780 WPM vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Miele WT 2780 WPM leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Miele WT 2780 WPM krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Miele WT 2780 WPM bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Miele WT 2780 WPM kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Miele WT 2780 WPM . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
