Gebruiksaanwijzing /service van het product K36 0005R van de fabrikant Milnor
Ga naar pagina of 21
Published Manual Number/ECN: H28 0010/2001074N • Publishing System: TPAS • Access date: 2/14/01 • Document ECN's: Latest Available Kit Instruction— K28 0010 K36 0005 K36 0005R PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.
Please Read A bout the Manual Identif y ing Information on the Cover The front cover d isplay s pert inent id entify ing in form ation fo r this m anual.
1.
MSSM020 4AE/833 2BV (1 of 1) È V-BELT TENSION ADJUSTMENTS FOR 30" AND 36" B-TYPE MACHINES AND 42" Q-TYPE MACHINES This instruction i s to be used for adjus ting the belt tension on the.
MSSM0301AE/9126B V È V-BELT TENSION ADJUSTMENTS This instruction is to be used for adjusting the belt tension on the following machine models: A belt tension testing device (Milnor ® part number 30T001) and a straight edge are required when using these instructions.
MSSM0301AE/9126BV (1 of 1) È V-BELT TENSION ADJUSTMENTS This instruction is to be used for adjusting the belt tension on the following machine models: A belt tension testing device (Milnor ® part number 30T001) and a straight edge are required when using these instructions.
M S S M A40 5 A E / 873 7 B V È V-BELT TENSION ADJUSTMENTS FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS This instruction is to be used for adjusting the belt tension on the followi.
MS SMA405 AE/ 8737 BV (1 of 2) È V-BELT TENSION ADJUSTMENTS FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS This instruction is to be used for adjusting the belt tension on the follow.
Ë Tensioning Banded Belts Ï 48032BHE, BTG , BTH 48 036QHE, QTG, QT Belt Deflect. (inches) Initial Tension (l bs.) (r ef.) Initial Tension (lbs.) (re f.) Belt Deflect (in.) Initial Tension (lbs. ) (re f.) Initial Tension (lbs. ) (re f.) WASH/ 2 SPEED WASH 9/32 6.
Ë Tensioning Banded Belts Ï 48032BHE, BTG , BTH 48 036QHE, QTG, QT Belt Deflect. (inches) Initial Tension (l bs.) (r ef.) Initial Tension (lbs.) (re f.) Belt Deflect (in.) Initial Tension (lbs. ) (re f.) Initial Tension (lbs. ) (re f.) WASH/ 2 SPEED WASH 9/32 6.
9.
M S S M 030 3 A E / 845 1 B V È MAIN BEARING AND SEAL REPLACEMENT FOR DIVIDED CYLINDER MACHINES This section applies to the front and rear cylinder shaft bearings of all divided cylinder machines (Rapid Load, Staph-guard ® , dye machines , et c.
MSSM 0303 AE/8451 BV (1 of 5) È MAIN BEARING AND SEAL REPLACEMENT FOR DIVIDED CYLINDER MACHINES This section applies to the front and rear cylinder shaft bearings of all divided cylinder machines (Rapid Load, Staph-guard ® , dye machines , et c.
inspection plate and use a timber to pry up the cylinder to remove cylinder weight from the bearings. Once the bearing is removed, the cylinder drops only approximately 1/32" before the shaft comes to rest on the shaft support.
inspection plate and use a timber to pry up the cylinder to remove cylinder weight from the bearings. Once the bearing is removed, the cylinder drops only approximately 1/32" before the shaft comes to rest on the shaft support.
Ê Replacing the Bearing Housing, Seal Sleeve, and Seals (Front or Rear) 1 . With the seal sleeve removed, press all old seals out of the bearing housing. Remove the large o-ring from the outside of the housing. Thoroughly clean the bearing housing and flush out all grease passages to make cer- tain they are unblocked.
Ê Replacing the Bearing Housing, Seal Sleeve, and Seals (Front or Rear) 1 . With the seal sleeve removed, press all old seals out of the bearing housing. Remove the large o-ring from the outside of the housing. Thoroughly clean the bearing housing and flush out all grease passages to make cer- tain they are unblocked.
Ê Measuring Unmounted Clearance and Setting Bearing (Front or Rear) The bearings used on Milnor ® washer and dye extractors are the very best anti-friction devices available for these applicati ons. However, the anti-frict ional characteristi cs of the bearings will be reduced if they ar e not proper- ly inst alled.
Ê Measuring Unmounted Clearance and Setting Bearing (Front or Rear) The bearings used on Milnor ® washer and dye extractors are the very best anti-friction devices available for these applicati ons. However, the anti-frict ional characteristi cs of the bearings will be reduced if they ar e not proper- ly inst alled.
Ê Tightening Bearing(s) (Front and/or Rear) 1. Once both bearings are seated, or if only one bearing was replaced, install the bearing lockwasher(s) and lock- nut(s).
Ê Tightening Bearing(s) (Front and/or Rear) 1. Once both bearings are seated, or if only one bearing was replaced, install the bearing lockwasher(s) and lock- nut(s).
Een belangrijk punt na aankoop van elk apparaat Milnor K36 0005R (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Milnor K36 0005R heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Milnor K36 0005R vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Milnor K36 0005R leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Milnor K36 0005R krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Milnor K36 0005R bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Milnor K36 0005R kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Milnor K36 0005R . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
