Gebruiksaanwijzing /service van het product KURSPK0026 van de fabrikant Milnor
Ga naar pagina of 30
Published Manual Number/ECN: HURSPK0025/99503N • Publishing System: TPAS • Access date: 03/06/03 • Document ECN's: Latest Available Kit Instruction— KURSPK0025 KURSPK0026 PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.
Please Read A bout the Manual Identif y ing Information on the Cover The front cover d isplay s pert inent id entify ing in form ation fo r this m anual.
MS S M 0 1 1 6 AE / 8 8 0 9 B V È SETTING LI MI T SWITCHES Ê Limit Sw itches—Incl uding Microswit ches— Will Be Damaged If Over-actuated! Any limit switch wi ll be damaged if it bottoms ou t forcefully.
MSSM0116 AE/8809 BV (1 of 2) È SETTING LI MI T SWITCHES Ê Limit Sw itches—Incl uding Microswit ches— Will Be Damaged If Over-actuated! Any limit switch wi ll be damaged if it bottoms ou t forcefully.
Ë Free Position of Rotary Lever —Attach the rot ary lever to the s haft so that, in t he free positi on, the lever is at a right angl e to the direction of rela tive movement bet ween the switch and target (see FIGURE 3). Ë Angle of Switch —Set a plunger swit ch so that the ta rget and plunger m ove parallel t o each other.
Ë Free Position of Rotary Lever —Attach the rot ary lever to the s haft so that, in t he free positi on, the lever is at a right angl e to the direction of rela tive movement bet ween the switch and target (see FIGURE 3). Ë Angle of Switch —Set a plunger swit ch so that the ta rget and plunger m ove parallel t o each other.
M S O P 0 9 2 2 AE / 9 8 0 5 A V È PRESS SAFETY FOR INSTALLATION AND SERVICE Ê General Safet y Requirement s (specific warn ings, next page and throughout manual) Incorrect installa tion, neglect ed.
MSOP09 22AE/98 05AV (1 of 2) È PRESS SAFETY FOR INSTALLATION AND SERVICE Ê General Safet y Requirement s (specific warn ings, next page and throughout manual) Incorrect installa tion, neglect ed pre.
Ê Danger From an Operating Press CRUSH HAZARD—Devices in and above the press move wi thout warning and can entangle, crush, or sever limbs on contact. ☞ NEVER touch or reach into assemblies i n or above press fr ame unless power is locked OFF and tagged out, and then only for maintenance.
HURSPK0026/00186 Page 1 of 21 INSTRUCTIONS FOR 50 KILO AND 60 KILO PRESS S HIM RETRO-FIT These instructions are for adding shims under the main bell air cy linder on 50 kilo and 60 kilo presses.
HURSPK0026/00186 Page 2 of 21 8. Replace the coupling onto the shaft on top of the 12 bolt-hole coupler shim. 9. Evenly torque the bolts of the coupling to 25 foot pounds (33.9 Newton meters) (using the cross torque method starting with the four bolts at the split of the coupling) .
HURSPK0026/00186 Page 3 of 21 21. Slide as many large shims in the g ap between the base and cross-member as possible. I f a gap re mains betwee n the larg e shims and the ma in bell air cy linder, slide as many smaller shims between the la rge shim and the base of the air cy linder to fill the remaining gap.
HURSPK0026/00186 Page 4 of 21 shaft bearing from the upper cross-member (See Figure 8). 34. Loosen the two bolts that join the shaft-lock to the rig ht-hand uplock jaw. Note the position of the uplock so that it can be reinstalled in the same position.
HURSPK0026/00186 Page 5 of 21 Reconnect the left-hand uplock jaw and shaft-lock together using the new lock-nuts provided in the kit and the existing bolts (only hand tighten these bolts at this time) .
HURSPK0026/00186 Page 6 of 21 59. Repeat step ( 49) for the othe r lock seg ments. Recor d all measure ments - they will be used in determining the thickness of the required shims. (Even if most of the measuremen ts are within the spe cified rang e, ea ch lock seg ment will still have to be shimmed.
HURSPK0026/00186 Page 7 of 21 clearances (that is, the clearances which should result when the new shim thickness is added or subtracted from the readings obtained earlier) are within the permissible range. 67. When all shim segments have been installed, tighten all bolts (nine for the 50 Kg press, twelve for the 60 Kg press).
HURSPK0026/00186 Page 8 of 21 Main Bell Air C y linder Bolts Trace Outline of Main Bell Air Cylinder Base on Upper Cross Member Figure 1 15.
HURSPK0026/00186 Page 9 of 21 Torque To 25 ft-lb ( 33.9 Nm ) Main Dom e Coupling Figure 2 16.
HURSPK0026/00186 Page 10 of 21 Downlock Shim s Placed on Bed in order to Shim Main Bell Air C y linder Figure 3 17.
HURSPK0026/00186 Page 11 of 21 One of the Four Main Bell Air Cylinder Bolts Figure 4 18.
HURSPK0026/00186 Page 12 of 21 Main Bell Air Cylinder Shim s 19.
HURSPK0026/00186 Page 13 of 21 Figure 5 Uplock Shaft N ut and Bolt Right-Hand Uplock Assem bly Bracket Air Cylinder Clevis Bracket Clam ping Bolt Left-Hand Uplock Assem bly Bracket Uplock Bracket Clev.
HURSPK0026/00186 Page 14 of 21 Figure 6 Left-Hand Side Lock Shaft Bearing Right-Hand Side Lock Shaft Bearing Lock Shaft Spacers 21.
HURSPK0026/00186 Page 15 of 21 Figure 7 Right-Hand Side Lock Shaft Bearin g 22.
HURSPK0026/00186 Page 16 of 21 Upper Cross -Member Shaft Lock Uplock Jaw Figure 8 23.
HURSPK0026/00186 Page 17 of 21 Figure 9 Square Holes in the Side of the Uplock Jaw ( File Paint off of the Inside surf ace of the Holes ) 24.
HURSPK0026/00186 Page 18 of 21 Figure 10 Old Setup of Dom e Full-Up Contact Switch and Bracket Figure 11 25.
HURSPK0026/00186 Page 19 of 21 New Positioning of Dom e Full-Up Contact Switch and Bracket Dom e Full-Up Contact Switch Bracket Dom e Full-Up Contact Switch Figure 12 26.
HURSPK0026/00186 Page 20 of 21 Figure 13 27.
HURSPK0026/00186 Page 21 of 21 Figure 14 Lock Ring Bolts Location of Downlock Shim s 28.
Een belangrijk punt na aankoop van elk apparaat Milnor KURSPK0026 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Milnor KURSPK0026 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Milnor KURSPK0026 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Milnor KURSPK0026 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Milnor KURSPK0026 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Milnor KURSPK0026 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Milnor KURSPK0026 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Milnor KURSPK0026 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
