Gebruiksaanwijzing /service van het product Tx2-1600 van de fabrikant Mimaki
Ga naar pagina of 166
MIMAKI ENGINEERING CO., LTD. TKB Gotenyama Building, 5-9-41, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, Japan Phone: +81-3-5420-8671 Fax: +81-3-5420-8687 URL: http://www.
The kinds of manuals and how to use them The following documents have been attached to Tx2-1600: Operation Manual (this document) “Operation Manual” explains how to operate Tx2-1600. Ink - UseGuidance (separate volume) “Ink - Use Guidance” explains recommended recipe of pre and post fabric tratment according to each ink.
- i - Foreword Thank you for purchasing MIMAKI T extile Jet Tx2-1600. Model Tx2-1600 is a color inkjet printer for printing on fabric with eight colors at high speeds. This operation manual describes the operation and maintenance of modelTx2-1600 Color InkJet Printer (hereinafter referred to as the printer).
- ii - FCC Statement (USA) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference when the equipment is operated in a commer- cial environment.
- iii - T ABLE OF CONTENTS Foreword ....................................................................................................................... i DISCLAIMER OF W ARRANTY .....................................................................
- iv - The media sensor ......................................................................................................... 1.17 Head hight adjustment rod and adjustment screw ........................................................ 1.17 Fablic retainer .
- v - Chapter 2 How to use the basic functions Operation ................................................................................................................. 2.2 Operation panel ............................................................
- vi - Relationship between image quality and printing speed [QUALITY] .............................. 3.8 Printing direction [DIRECTION] ...................................................................................... 3.9 Returning speed up [RET .
- vii - When not in use the machine over the long term [STORAGE WSH] ........................... 4.19 Move the carriage to the left maintenance station [CARRIAGE] .................................. 4.23 Adjusting the head height when the fabric used is changed [HEAD HEIGHT] .
- viii - Features The features and methods of operation are explained in this manual for you to understand how to use the printer properly . Setting for 2-way multi printing Alternatively , using two sets of three heads in 2-way printing mode, each with different inks, gives you the functionality of two 8-color printers in a single unit.
- ix - Fabric retainer If the edge of the fabric is curled or it is raised, the fabric retainer can be used to avoid contact of the fabric and ink head. The fabric retainer can be adjusted thickness of up to 4 mm and 3-7 mm. Ditch for penetrated ink Even with printing to a coarse-textured fabric, the backing fabric is not stained by penetrated ink.
- x - How to read this Operation Manual Display on the LCD and indication of the keys In this Operation Manual, the characters displayed on the LCD of the operation panel and the keys used to operate the printer are explained, together with the operation procedure.
- xi - The operation key The information that is displayed on the LCD during plotter operation is explained. The pages of each chapter are given serial numbers starting from 1. Notes to sentences, caution on plotter operation, and hints for effective use of the plotter are given.
- xii - Safety symbols used in this Manual Safety signal words Pictorial signs are used in this Operation Manual for safe operation of and in prevention of damages to the printer . Pictorial signs and their meanings are given below . Read and fully understand before reading the text.
- xiii - Structure of this Manual Foreword This foreward describes the notice before operation and how to read this Operation Manual. Chapter 1 Setup This chapter describes the procedures for unpacking and assembling the printer , and for setting up the printer such as setting inks and fabric.
- xiv - • Be sure to use the printer with the power supply specifications indicated. Be sure to connect the plug of the power cable to a grounded receptacle. If not, fire or electric shocks can result. •T ake care not to damage, break or work on the power cable.
- xv - Position of the warning label This printer is adhered with a warning label at four locations. Be sure to fully understand the warning given on the labels. In the case where any of the warning label has become so soiled that the warning message is illegible or has come off, purchase a new one from your local distributor or our of fice.
- xvi -.
- 1.1 - Chapter 1 Setup This chapter describes the procedures for unpacking and assembling the printer , and for setting up printer such as setting inks and fabric. T able of contents Installation of the printer .......................................
- 1.2 - Installation of the printer Where to install the printer Secure a suitable space before using the printer . The space is required not only for the printer itself but also for printing operation. Length Width Height Gross weight Tx2-1600 2750 mm 750 mm 1350 mm Approx.
- 1.3 - Precautions in installation Do not install the printer under the following emvironment: A place exposed to direct sunlight A place in which temperature and humidity vary by a great margin Use the printer under the following environment.
- 1.4 - Checking the accessories Open the packing box and check the components in it. If you find any missing accessory or damaged one, please contact your local dealer . • It varies according to your order for Ink Cartridge and the additional accesories.
- 1.5 - Printing film (for adjustment of the device) Slip sheet bar Centering sensor unit Phillips screwdriver Power cable Hexagonal wrench (L) Ink Cartridge (separately sold) 1394 Driver(CD-ROM) Grou.
- 1.6 - Unpacking and Assembling Assembling the stand and the device • The package weight is as heavy as approximately 250 kg. Perform the assembly work by at least four persons to ensure safety . • Exercise added care not to drop the main unit on your feet.
- 1.7 - 3. T ake the stands out of the package. Direct the stands so that round tapped holes for the screws are faced outside. Set up each stand with the side having a groove for fitting the stay coming inside. 4. Attach the take-up device stand stay to the leg.
- 1.8 - 6. Holding both ends of the main unit with four per- sons. Hold up the device at the pedestal support bars. 7. Place the main unit on the stands while exercis- ing care not to allow hands to be caught between them.
- 1.9 - 9. Connect the cable of take-up device into the con- nector located at the left bottom of the main unit. Attaching take-up auxiliary bar Align the screw hole of the take-up auxiliary bar with the screw hole on the front face of the stand, then fasten the screws.
- 1.10 - Attaching centering sensor unit Align the screw hole of the centering sensor unit with the screw hole of the run-out auxiliary bar , then fasten the screws. Attaching loading unit Align the screw hole of the run-out device with the screw hole of the stand, then fasten the screws.
- 1.11 - How to remove the stopper 1. Loosen a screw fastening the Head Stopper , us- ing Driver . 2. Remove the Head Stopper as shown on the Photo. Putting on the maintenance cover 1. Put on the maintenance cover . 2. Fix the maintenance cover with the screws.
- 1.12 - Attach the waste ink hoses. 1. Set the waste ink hoses. 2. Secure the supplied hose retainer with screws and then attach the waste ink hoses to the de- vice unit. Attaching slip sheet bar Put the slip sheet on the hanger on the inner side of the stand.
- 1.13 - Configuration and Fnction Front face Name Function 1. F ront cover It is opened when setting fabric or taking a correctiv e measure against a f abric jam. 2. P arallel connector Bi-directional parallel interf ace connector (complies with IEEE1284) 3.
- 1.14 - Rear face Name Function 1. F-row ink station This station houses up to eight ink cartridges. 2. Clamp lever It is made to go up-down the pinch roller for holding fabric. 3. Centering sensor unit This sensor detects the fabric edge and optical axis so that the fabric be fed straight.
- 1.15 - Names and function of the parts under the front cover Under the front cover , there are the carriage, capping station, etc. necessary for printing operation. The mechanisms provided under the front cover are explained below . Carriage The carriage is provided with print heads for printing, etc.
- 1.16 - Capping station The capping station consists of ink caps, wipers for cleaning the heads, etc. Ink Cap : It covers the nozzles of print head to prevent from drying up. W iper : It is used to clean the head nozzles. • Clean the capping station frequently to keep the capping station clean.
- 1.17 - Height adjustment screw Support screw Secures the Height adjustment screw to prevent it from coming loose. Used to adjust the head height. Head height adjustment rod Measures the thickness of the media to be used as a reference for head height adjustment.
- 1.18 - Fablic retainer If the edge of the fabric is curled or it is raised, it may be caught by the head or inferior ink discharge may occur . To avoid this trouble, use the fabric retainer . • The fablic retainer also act as a detection board which detects the printing width.
- 1.19 - Ditch for penetrated ink and platen boards Printing on a coarse-textured fablic may cause ink to penetrate the fabric. If the fabric runs out in this condition, it may be stained by the ink on the platen. The ditch for penetrated ink is provided to avoid this trouble.
- 1.20 - About other setup Attaching lapel bar The lapel bar is used to stabilize the media tension of the run-out side. If the media tension of the roll-out side becomes unstable, printing is adversely affected (ver- tical black or white lines occurs).
- 1.21 - 3. Insert the lapel bar into the hole of the side plate and then allow it to slip in the lower slot. 4. Make sure that the bearing is put into the side plate and that the lapel bar is set to the position where it rotates easily .
- 1.22 - Attaching the platen boards Attach the platen boards when using a fabric without ink penetration. Set the attachment position and orientation of the platen boards in three steps according to the degree of ink penetration. (See page 1.14) The F cover is closed.
- 1.23 - Changing gap for fablic retainers • When the thickness of the fabric used is 0 to 4mm, use it with the stainless plate adjusted by moving the outside long hole hole and then secured with a screw .
- 1.24 - Connecting the cables Connecting the interface cable Connect the printer to the computer with the appropriate interface cable. T wo types of interface cables are available. Select the interface cable appropriate to the computer and output software.
- 1.25 - Connecting the power cable Connect the power cable to the receptacle of the following specifications. •V o l t age : AC 100 - 240 V ± 10% • Frequency : 50/60 Hz ± 1% • Capacity : 5 A or more (500 W or more) • Be sure to turn of f the power switch of the printer in prior to the connection of the power cable.
- 1.26 - Switching ON/OFF the power supply After setting up the printer , switch on and off the power as described below . T urning the power on STEPS: 1. T urn on the power to the computer , etc. that are connected to the device. 2. T urn on the power to the printer .
- 1.27 - T urning the power off To turn the power of f, check first whether or not there is data received and there remains data that has not yet been output. Also be sure that the head rests at the capping station. • If the power is turned of f while the printer is engaged in printing, the head may fail to be retracted in the capping station.
- 1.28 - Front cover and maintenance cover Opening/closing the cover Do not open the front cover and the maintenance cover while the printer is in operation. If you open the front cover or the maintenance cover during printing, the carriage will stop for safety , reselting in abortion of printing.
- 1.29 - Ink cartridges T ypes of ink 3 types of ink are available for this printer at the moment. The characteristics of each ink type are described below . Acid dye ink [Acid] : Suitable for wool, silk, and other animal fibers and nylon. A vailable ink colors include black, cyan, magenta, yellow , light cyan,light magenta, gray , blue and red.
- 1.30 - Ink stations As viewed from the front of the printer , the ink station on the right side is called the “F-row ink station” and the ink station on the left side is called the “R-row ink station.” • In each ink station, set eight ink cartridges containing ink of the same type.
- 1.31 - R-row Ink Head F-row Ink Head R-row Ink Station Ink Head F-row Ink Station D BG CE F AH BD G 35 6 18 24 7 ACEG BDF H 13 57 24 68 Relationships between ink station and head row The right ink station supplies ink to the front row (F-row) of heads.
- 1.32 - Setting ink cartridges Setting for 1-way high-speed printing New piezo electric heads, the staggered-layout print head provides more attractive, faster printing, and allows ultra high-precisions 8-head 1-way printing. Set the left and right ink car- tridge cases with ink cartridges of the same types and same colors.
- 1.33 - • Set ink cartridges of dif ferent types and colors to 1 through 8 and A through H. • During initial ink setting or ink change, register the appropriate ink type for each ink station (See page 1.32). • It is necessary to register ink type to the printer for checking the printing information and switching the head set.
- 1.34 - Fabric for printing This section describes the types of fabric that can be used with the printer and the method of setting the media used. T ypes of fablic that can be used The types of fabric that can be used with this printer “Roll” and “Leaf” fabric are cut sheet media.
- 1.35 - Precautions in handling the fabric Carefully observe the following when handling the fabric. • Use pre-processed fabrics recommended by MIMAKI. •W hen setting the fabric used, be sure to adjust the head height. Otherwise, the fabric and/or the head can be damaged.
- 1.36 - Before setting the fabric on the printer Before setting the fabric, be sure to confirm the Ditch for penetrated ink. If ink is there, wipe them with a waste cloth. (see more details 2.14 ) Adjusting the head height according to the fablic [HEAD HEIGHT] It is necessary to adjust the head height according to the thickness of the fabric.
- 1.37 - 2. Press the [FUNCTION] key . 3. Press the JOG keys[ ] and [ ] to select [MAIN- TENANCE]. 4. Press the [ENTER] key . 5. Press the JOG keys[ ] and [ ] to select [HEAD HEIGHT]. 6. Press the [ENTER] key . • If the fabric is loaded, “REMOVE MEDIA” will be displayed.
- 1.38 - 2. Push down the head height adjustment rod by the right hand. Push down the head height adjustment rod till it stops moving anymore. • If the tip of the head height adjustment rod makes contact with the surface of the fabric, repeat step 10.
- 1.39 - 10. Press the [ENTER] key . The carriage will come back to the capping station. The LCD shown on the right is displayed. Points in head height adjustment • When the head height is so adjust.
- 1.40 - Setting the mating sheet The mating sheet is used to prevent ink penetration of the fabric which is not dried after printing. 1. Set the fabric core of the slip sheet to the slip sheet bar hanger . Adjusting parallelism of loading unit If the parallelism of the loading unit is remarkably broken, the fabric deviation or wrinkle may occur .
- 1.41 - Setting The FabricT o The Printer The fabric that can be used are roll and leaf fabric. Leaf fabric is handled in the same manner as roll fabric for printing. When using leaf paper for setup list printing, for example, be careful about the setting posi- tion.
- 1.42 - 3. Loosen the screw of the right-hand roll holder . Adjust the roll holder position to the width of the roll fabric. 4. Insert the right-hand roll holder into the core of the roll fabric. When the roll holder have been inserted all the way into the fabric core, secure it with the screw .
- 1.43 - 6. Pull out the fabric from the rear side of the printer to the height of the Y cover . 7. Insert the leading edge of the fabric between the driver roller and pinch roller . Be sure to lead the fabric outside the shaft of the centering sensor .
- 1.44 - 9. Pull out the leading edge of the fabric from the front face of the printer . • Open the front cover , move up the clamp level while holding the leading edge of the fabric with your hand, then pull out the fabric. 10. Rewind the roll holder or fabric core several times from the rear face of the printer .
- 1.45 - Setting the centering sensor position After setting the fabric to the printer , please set the centering sensor position. •W hen adjusting the optical axis after the cloth width detection, the beep will not sound. Please make sure to adjust the centering sensor position before detecting the cloth width.
- 1.46 - Attaching empty fablic core for taking up To take up the fabric after printing, attach an empty fabric core to the take-up device. 1. Close the front cover to allow detection of the roll fabric. 2. Push the JOG key [ ] and [ ] to move the lead- ing edge of the fabric to the position of the empty fabric core.
- 1.47 - Removing pinch roller and preventing wrinkle of fablic • If either edge of the fabric stretches longer than the center or if an edge of the fabric is thickened because of gumming processing to prevent fray , slack may occur easily . In this case, remove the pinch rollers at both ends of the fabric.
- 1.48 - 4. To prevent fall-off or loss of the hand screws, lightly fasten them. • If the lengths of the fabrics at the left and right pinch rollers removed are dif ferent remarkably , reset the fabric.
- 1.49 - Specifying the scope of printing on the fabric used (Effective printing area) The printer has an area which cannot perform printing, due to mechanical reasons. This area is called “margin.” The effective printing area is obtained by excluding the margin from the printing fabric.
- 1.50 - Origin setting Establish an origin in terms of data on fabric loaded on the printer . Place the fabric and cause the printer to detect the fabric, the origin is automatically established at the location shown in the illustration given below .
- 1.51 - Moving the printer The method of moving the printer to the place of installation is explained below . When moving the printer , unlock the caster stoppers. • When moving the printer take care not to apply excessive shock to it and it must be held up by at least two persons.
- 1.52 -.
- 2.1 - Chapter 2 How to use the basic functions This chapter describes the basic operations of the printer , from the beginning to the end of printing. Before using the application functions, understand how to use the basic functions of the keys on the operation panel and the modes in which the menus are displayed on the LCD.
- 2.2 - Operation This section describes the operation panel that is used to operate the device and the menus from which to choose the desired item. Operation panel The operation panel that is used to operate the device and a method of maintenance of the device after operation, etc.
- 2.3 - Functions of the JOG keys Each of the JOG keys varies in function according to the time at which it is used. The functions of the JOG keys are explained below . Before the detection After the detection When selecting a When inputting a choice selected among of a sheet of a sheet function several alternatives Selects the roll media.
- 2.4 - Menu tree The operation of printer and printing conditions are set by pressing the appropriate operation keys, selecting the desired setting item and setting detailed conditions. In order to operate the printer properly , it is necessary to understand the structure of the menu tree (See page Appendix.
- 2.5 - Some menus simply list items which do not require the operator to set any of them. In this case, the operator is required to select the content to be displayed on the LCD. [Operation key] DISPLAY The operation mode is displayed. The amount of ink that remains is displayed.
- 2.6 - Setting the display language Set the language in which to display characters on the LCD. “English” has been set as the initial display language of the printer . T ry to change the display language to “Japanese” here. STEPS: 1. Make sure the mode is LOCAL mode.
- 2.7 - Printing an image from saurce data Starting the printer operation This section describes the basic operation of the printer . Printing conditions can be set on the printer side. In this section, however , the method of printing an image from data that has been set on the computer side and transmitted to the printer is explained.
- 2.8 - Information on printing data Key operation on REMOTE mode [REMOTE] key : In case pressing [REMOTE] key when the printing data has not received, the mode is entered LOCAL mode. In case pressing [REMOTE] key when the printing data has received and printing has been performed, complete scan performance and the mode is entered LOCAL mode.
- 2.9 - Correcting the media feed rate during printing [Feed Comp.] Even for fabric of the same type, if the thread size or texture is slightly different, the proper value of the feeding amount changes. In this case, correct the feeding amount of the fabric while checking the printing condition.
- 2.10 - 5. Press the [ENTER] key to return to the REMOTE display . The changed setting value is saved. The value is to be in ef fect performing till the turning off. Press the [END] key to return to the REMOTE display . The changed setting value is to be in effect performing till the turning off.
- 2.11 - Checking nozzle in ink firing condition Executing the test draw [TEST DRA W] In prior to the actual printing or after the execution of the cleaning function, a test pattern is plotted to chec.
- 2.12 - If there are nozzle clogging in ink firing condition Cleaning ink heads If a test pattern plotted is defective, execute the cleaning function to clean the associated ink head. After cleaning the ink head, make the device plot a test pattern again.
- 2.13 - Routine maintenance Be sure to conduct maintenance works for the device when necessary or periodically so as to use the printer for a long time while keeping its printing accuracy . When the device is left unused for a long period of time •T urn off the power .
- 2.14 - Cleaning the wiper shaft The dirty wiper shaft may cause the wiper malfunction and resulting an error display . Maintenance for frame components If the frame components of the device have stained, dampen a piece of soft cloth with water or neutral detergent diluted with water , squeeze it and wipe the frame components clean.
- 2.15 - To replenish ink, set a new ink cartridge in the ink station Setting a new ink cartridge is required when the ink is to be replenished or when the device becomes the following condition. If the ink cartridge is not replaced, the carriage stops during the printing operation when the ink runs out.
- 2.16 -.
- 3.1 - Chapter 3 How to use the application functions After you have mastered the operations described in Chapter 2 “How to use the basic functions,” you should learn how to use the application functions whereby you can set printing conditions on the printer side and put the printer into operation.
- 3.2 - [ FUNCTION ] DISPLA Y [ FUNCTION ] MAINTENANCE [ FUNCTION ] SET UP Application functions The application functions make it possible to modify the printing conditions that have been set for source data received from the computer . The [FUNCTION] key is used to set up the application functions.
- 3.3 - Before setting printing conditions in the function menu The basic operation of the function menu for setting individual printing conditions is explained below . Set the individual printing conditions in the function menu after performing the following three operations.
- 3.4 - Changing the type Note that the current type cannot be changed while the device is in operation. To change the type during printer operation, first stop the device (See page 2.10) and then select the desired type in the LOCAL mode. • Only the setting of the following items can be changed during printing.
- 3.5 - Adjusting the lapal bar Diverse types of media are used for inkjet printers: different raw materials including natural materials, synthesized materials, etc. and materials with different manufacturing processes including textile fabric, knit fabric, etc.
- 3.6 - T roubleshooting The following describes general troubleshooting. With some corrective mesures, problems may not be solved depending on the media used. If a problem cannot be solved after per- forming test printing several times, stop using the printer .
- 3.7 - After setting the fabric to be printed Correcting error of amount of feed depending on fabric [MEDIA COMP .] The printer prints an image on the fabric while feeding it forward little by little. When the thickness of the fabric changes, the optimum feed rate changes accordingly .
- 3.8 - Setting printing conditions Changing printing conditions on the printer side Set up the printing method that determines the quality of image. For the printing method, there are three setting items - “quality of image”, “direction of print- ing” and “Returning speed of the head.
- 3.9 - Printing direction [DIRECTION] This function sets the direction of printing. The printer prints an image while moving the carriage right and left. By setting the direction of printing, it is possible to adjust the image quality and the printing speed: “Uni-directional” and “Bi-directional.
- 3.10 - Returning speed up [RET . SPD UP] In case the printing width is 1000mm or less when uni-directional printing, the nozzle drop out may occur . Using this function to slow down the returning head speed may solve the trouble. ON : The head returns with normal speed.
- 3.11 - Improving the density of ink color [INK LA YERS] This function prints the data in two or more layers (wet-on-wet coating) to improve the density of ink color . If a coarse-surfaced fabric (e.g., canvas) is used, the color of ink might be weak.
- 3.12 - Setting the ink drying time [DR YING TIME] This function sets an ink drying time. The drying time is the wait time by scanning and the time interval between the instant at which the printing operation is completed. Specify the time to be established in accordance with the printing resolituion on a drawing and the type of fabric to be used.
- 3.13 - Deciding the priority of settings by the computer or the plotter [PRIORITY] This function gives priority to either the printing conditions set on the computer or the printing conditions set on the plotter . Printing conditions can be set on data of the plotter and on data received from the computer using the output software.
- 3.14 - 9. Press the JOG keys [ ] and [ ] to select the priority [HOST] or [PLOT] of the driying time. Here, select [PLOT]. 10. Press the [ENTER] key . 11 .P ress the JOG keys [ ] and [ ] to select the priority [HOST] or [PLOT] of the ink type. Here, select [PLOT].
- 3.15 - Increasing (decreasing) the right and left margins of the fabric [RIGHTmargin]/[LEFTmargin] This function sets an effective printing area to increase/decrease the right and left margins of the fabric. The blank portion of the fabric is called maigin.
- 3.16 - Setting [LEFTmargin] STEPS: 1. Select a type.(See page 3.3) Here, select T ype 1. 2. Press the [ENTER] key . 3. Press the JOG keys [ ] and [ ] to select [MARGIN]. 4. Press the [ENTER] key . 5. Press the JOG keys [ ] and [ ] to select [LEFTmargin].
- 3.17 - When using the plotter in an extremely dusty or dry place [REFRESH] Solidification of ink can be prevented by refreshing the head during printing. If the plotter is used in a dusty place or dry place, ink in the head will be likely to solidify .
- 3.18 - Setting a unit of length displayed on the LCD [MM/INCH] This function sets a unit of set values displayed on the LCD. Use this function when displaying “width” and “length” of the fabric after setting of the origin or detection of the fabric.
- 3.19 - Setting the type of ink to be used [INK TYPE] This function selects the type of ink that is to be used. This plotter permits up to two types of ink to be loaded. When starting an actual printing operation, however , select only one type of ink to be used according to the printing data and the fabric used.
- 3.20 - Setting up auto-cleaning function [AUT O CLEAN] Setup the auto-cleaning function. Printing failures may be remarkable on dusty locations or locations with low temperature. Perform cleaning for each plot to prevent printing failures. ON : The head is cleaned automatically .
- 3.21 - Setting up auto-cleaning function [AUTO CLEAN2] Perform cleaning after when plotting specified length and prevent printing failures. ON : The head is cleaned automatically after when plotting specified length. OFF : The head is not cleaned automatically during plotting.
- 3.22 - 8. Press the [ENTER] key . The screen to specify interval of cleaning displays on LCD. 9. Press the JOG keys [ ] and [ ] to select the length to execute the cleaning performance. (0.1 to 10.0m in 0.1m unit) 10. Press the [ENTER] key . 11 .P ress the [END] key twice.
- 3.23 - Back feed Setting for End of printing [EndOf PRINT] This function sets the operation when printing completes. If back feed is set to ON, eliminate the waste space on media by feeding back the media . ON : Media back feed is performed by setup value(1 to 60mm).
- 3.24 - Continuing printing after [Ink Near End] [PRINT CONT .] If the remaining amount of ink decreases during printing and [Ink Near End] appears, you can replace ink for each ink station and then continue printing for the next file. ON : Even if [INKnearEND] appears, you can use only one ink station to continue printing for the next file.
- 3.25 - Preventing the fabric skew [CENTERING] This function of centering prevent the media skew . Set this function when using the roll media those left or right edge are not lined up. A sensor monitors the media right edge position and move the roll media to prevent printing run off the edge.
- 3.26 - Enabling the take-up unit [T AKE-UP] This function enables the take-up unit. INTER V AL : T ake-up operation is performed according to the slack sensor .
- 3.27 - Resetting printing conditions by type [SETUP RESET] This function resets the current printing conditions to the factory-set printing conditions. Execute this function for each of the types of set printing conditions. STEPS: 1. Select a type. (See page 3.
- 3.28 -.
- 4.1 - Chapter 4 Maintenance functions In order to keep the printer in good operating condition, it is necessary to carry out maintenance of the printer periodically . This chapter describes the functions that help solve the problem of deteriora- tion in image quality and replace a waste ink tank.
- 4.2 - Maintenance of the printer The term “maintenance” as used herein refers to the operation that has to be performed to keep the printer in good operating condition. To carry out maintenance of the printer , select [MAINTENANCE] from the function menu and make the necessary settings.
- 4.3 - Before starting maintenance Checking the menu mode Before executing any of the maintenance functions, check the menu mode. The menu mode must be the LOCAL mode or the FUNCTION mode before maintenance can be started. Make sure that either <<LOCAL>> or <<FUNCTION>> is displayed on the LCD.
- 4.4 - Maintenance functions Press the [FUNCTION] key and set up the desired maintenance function. Drawing setup conditions [LIST] This function outputs the current settings of the printer . They are useful in carrying out maintenance of the printer .
- 4.5 - Printing HEX code of printing command [DA T A DUMP] This function prints data commands received from the computer , in HEX code. The HEX code is an alphanumeric representation of printing commands. By using this code, it is possible to check if there are any abnormal data commands.
- 4.6 - Correcting the dot positions after adjusting the head height [PRINT adjust] When the head height is adjusted, be sure to correct the dot positions. Since the adjustment of head height is done by hand, the head will slightly deviate from the correct position (See page 1.
- 4.7 - 6. Repeat Steps 4 and 5 to correct the dot positions on Patterns 2 to 7. Select the correct dot positions on each of the patterns. When pressing the [ENTER] key after setting the correction on pattern 7, the right indication is shown. 7. Press the [END] key twice.
- 4.8 - Moving the carriage to clean the station interior [CARRIAGEout] This function moves the carriage for maintenance of the ink station. The interior of the station needs maintenance when a blurred test pattern is not corrected even after the cleaning function (page 2.
- 4.9 - 6. Close the maintenance cover , then press the [ENTER] key . The menu enters the LOCAL mode. If a defective printing is not corrected even after the cleaning function is executed Cleaning the.
- 4.10 - Periodical cleaning of the wiper Cleaning the wiper The wipers are provided for cleaning the heads. As the printer is used to print images, the wipers gradually become stained with ink and dust. Clean stained wipers. The wiper is separately available from your local distributor or our office.
- 4.11 - When the message [Replace Wiper] is displayed [WIPER EXCHG] The wipers are consumable parts. As the wiper continues cleaning the head, it gets stained with ink and dust. The printer counts the number of times the wipers are cleaned and tells when to replace them.
- 4.12 - 7. Holding the projections at both ends, insert a new wiper into place. •D o not touch the rubber portion of a new wiper . It can cause the nozzle to be clogged. • Insert the wiper so that its felt side surface is placecd on the left as viewed fromyour position.
- 4.13 - When the message [Clean Wiper Shaft] is displayed The message shown on the right is displayed after several numbers of wiping. Please clean the wiper shaft at once if this message is displayed. Extremely dirty wiper shaft may cause wiper malfunction and resulting an error display .
- 4.14 - Cleaning the nozzle [NOZZLE CLN] Clean up the nozzle as for nozzle clogging. If nozzle clogging cannot be resolved even after cleaning several times, execute the [FILL UP INK] function. (Page 4.25) If this error cannot be resolved with these functions, contact the dealer .
- 4.15 - 7. Clean the wiper . Use and push a swab contained cleaning liquid to take off some dust on the felt surface. Use a swab contained cleaning liquid to take off some inks on the rubber surface. 8. Clean the wiper and press the [ENTER] key . 9. Fill the cap with the cleaning liquid using a syringe.
- 4.16 - 11 . press the [ENTER] key . 12. Press the JOG keys [ ] and [ ] to select the time to leave. (1-99 minutes: 1 min unit) 13. Press the [ENTER] key . The initial operation is performed. Remaining time is displayed. After remaining time is over , execute cleaning.
- 4.17 - Ink discharge way cleaning [DRAIN W ASH] The ink discharge way may become clogged by coagulated ink. It must be cleaned at regular intervals to avoid clogging. Ink dischar ge way: T ubing between the cap and the waste ink tank •D o not move the carriage out of the capping station by hand.
- 4.18 - 6. Remove the cleaning liquid with a syringe. During the suction pause period, drop the cleaning liquid until just before it overflows from the cap. 7. Close the maintenance cover . 8. Press the [ENTER] key . Dry suction continues for 30 seconds and the initial operation is performed.
- 4.19 - When not in use the machine over the long term [STORAGE WSH] When not in use the machine over a week, perform [STRAGE WSH] function to clean the head nozzle and ink dischar ge way . After performing the function, store the machine. •T wo colors (two cartridges) per head are used.
- 4.20 - 7. Holding the projections at both ends, draw out the wiper . Use the gloves that are supplied with the separately-available cleaning wiper to protect your hands from stains. 8. Use a swab soaked with the cleaning liquid to clean off ink blots on wiper and bracket.
- 4.21 - 12. Close the maintenance cover . 13. Press the [ENTER] key . 14. Press the JOG keys [ ] and [ ] to select the time to leave. (1-99 minutes: 1 min unit) Normally set 1 min. 15. Press the [ENTER] key . The initial operation is performed. Remaining time is displayed.
- 4.22 - 18. Clean the wiper and press the [ENTER] key . 19. Fill the cap with the cleaning liquid using a syringe. Dry suction starts in cycles consisting of 10 seconds of suction followed by 10 seconds of pause. Repeat the performance of the air aspiration several times to clean up the ink discharge way .
- 4.23 - Move the carriage to the left maintenance station [CARRIAGE] This function move the carriage to the left maintenance station to chack the head, to clean the nozzle surface and to do maintenance of carriage. STEPS: 1. Select [CARRIAGE] from [MAINTENANCE].
- 4.24 - << L OC A L > > wi d t h : 1 2 7 2 m m IN T I A L I Z I N G PLE A S E W AI T 6. Close the left maintenance cover , then press the [ENTER] key . •I n the case where a fabric is loaded on the printer , the fabric detection display will appear on the LCD after the initialization.
- 4.25 - Menu displayed after the ink cartridge is installed [FILL UP INK] When the ink cartridge is replaced with a new one or a new ink cartridge is installed, the printer charges ink automatically . Therefore, a menu for charging ink is included in the main- tenance functions.
- 4.26 - When charging ink different from the one in use [INK CHANGE] The INK CHANGE function charges ink different from the one currently in use. When the same type of ink as is set in the ink station is to be used, it is unnecessary to execute this function.
- 4.27 - 8. T ake out the changing ink cartridge from the ink station. When removing the ink cartridge, “-” is displayed on LCD. When all the ink cartridges are taken out, the discharge of ink is started automatically . 9. When the LCD shown on the right appears, install the washing liquid cartridge.
- 4.28 - 15. Press the [ENTER] key . Filling of ink is started automatically . When filling of ink is completed, the display shown on the right is indicated.
- 4.29 - << L OC A L> > wi dt h : 1 2 7 2 m m MA I N T E N ANC E USE H E A D< ent> USE H E AD HEAD L I NE : A L L USE H E AD HEAD L I NE : R E A R MA I N T E N ANC E USE H E A D< .
- 4.30 - Check the stretch and shrink of fabric after the printing [STRETCH CHK] Check whether the cloth is stretching or shrinking after the printing.
- 4.31 - STEPS: 1. Select [STRECTH CHK] from [MAINTENANCE]. (See page 4.3) 2. Press the [ENTER] key . 3. Press the JOG keys [ ] and [ ] to select the density . [50%], [100%], [200%], [300%] • 200 % of density is recommended for check- ing the stretch and shrink on printing at reso- lution 720 dpi.
- 4.32 - Displaying the printer information [INFORMA TION] Displays the firmware version of this printer . If trouble occurs, please inform the dealer or MIMAKI sales office of the contents of the trouble as well as this information. STEPS: 1. Select the [INFORMA TION] from the [MAINTE- NANCE].
- 5.1 - Chapter 5 When abnormal conditions are encountered Chapter 5 describes corrective measures to be taken in the case where an abnormal phenomenon arises on the printer and where an error mes- sage is given on the display . T able of contents Before taking a phenomenon as a sign of failure .
- 5.2 - Before taking a phenomenon as a sign of failure Corrective measures against troubles in the case where no error message is given on the LCD are described in this section. Be sure to take the following measures before taking the trouble as a sign of failure.
- 5.3 - Paper jamming arises/fabric is soiled A jam of the fabric or a stained fabric is considered to occur when an unsuitable fabric is used or the fabric is set improperly . Is a pre-processed cloth which suits the ink used ? Is the cloth wrinkled or folded at both edges ? Use cloths which do not become elastic with water.
- 5.4 - If image quality declines Corrective measures against troubles in the case where satisfactory image quality is not provided are described in this station.
- 5.5 - T roubles for which error message are given on the LCD If something is wrong with the printer , the buzzer sounds and a corresponding error message is given on the LCD.
- 5.6 - W arning message Cause Corrective measure The set ink cartridge is not a genuine product. Cleaning period of the ink on the wiper shaft of the capping station. Head ID has not been registered. Time to replace the battery Clamp lever set down without media.
- 5.7 - Error messages Error messages indicates error numbers. If any error message is given on the LCD, turn off the power to the printer and turn it on after a while. If the same error message appears again on the LCD, contact your local MIMAKI distibutor or MIMAKI office to call for service.
- 5.8 - An error occurs in communica- tion between I/F board and main board. I/F board has not been installed. HOST I/F Timeout error has arisen during communication between the host computer and interface board. Initial operation failure of the I/F board and control board.
- 5.9 - The printer has failed to detect the fabric. The printer has failed to detect the origin. The take-up unit error has been occured because of sensor error. The centering unit error has been occured. The centering unit has not been connected properly.
- 5.10 -.
- A.1 - Appendix This appendix describes the specifications and components the pr inter , function menu structure. T able of contents Basic specifications ............................................................................................. A.
- A.2 - Basic specifications Item Tx2-1600 Printing head Method Piezo-electric drop on demand Specification Eight-heads (4 x 2 lines, Stagger arrangement) Nozzle Multi ink set printing: 360 nozzles fo.
- A.3 - Fabric skew 5 mm or less / 10 m (In case the fabric is aligned.) Head height adjustment 1.2 mm to 10 mm variable from the platen surface Cutting of fabric Cutter function not provided. Waste ink tank Waste ink hose is packaged standard (Waste ink tank not pro vided) Interface IEEE1394, IEEE1284 Command MRL-1E (ESC/PV.
- A.4 - Optional extras Item Item no. Qty . Remarks Ink cartridge See the list above. Bemcot BEMCOT M-3 100 pcs. Swab Swab 6 wooden shaft S 10 pcs. Wiper SP A-0105 4 pcs.
- A.5 - Function flow chart <<LOCAL>> X=xxxx Y=xxxx ORIGIN SET UP 0.0 0.0 <<LOCAL>> width:1620mm CLEAN. :12345678 SELECT :ABCDEFGH CLEANING TYPE :NORMAL CLEANING 00: ∗∗ : .
- A.6 - FUNCTION key; FUNCTION SETUP SELECT :TYPE1 TYPE ∗ PRINT MODE <ent> TYPE ∗ MODE QUALITY : STD TYPE1 to 4 :STD, FINE, HIGHspd << LOCAL >> width:1620mm FUNCTION SETUP <ENT> TYPE ∗ MEDIA COMP .
- A.7 - To be followed TYPE ∗ SETUP RESET <ent> TYPE ∗ RESET : ent FUNCTION SETUP <ENT> :INTERV AL,ON, OFF TYPE ∗ T AKE-UP <ent> TYPE ∗ T AKE-UP :INTER V AL :ON, OFF TYPE ∗.
- A.8 - : ENGLISH, JAP ANESE, PORTUGUESE, IT ALIANO, ESP ANOL, FRANCAIS, DEUTSCH INFORMA TION VIEW :SERIAL NO. SERIAL NO. S/N ∗∗∗∗∗∗∗∗∗ MAINTENANCE INFORMA TION <ent> INFORMA TION VIEW :VERSION MAIN V er1.00 I/F V er1.00 MAINTENANCE INK CHANGE <ent> InkSet R : Acid F : Disp Followed D201546-1.
.
Printed in Japan D201546 © MIMAKI ENGINEERING CO., LTD. 2006 KM.
Een belangrijk punt na aankoop van elk apparaat Mimaki Tx2-1600 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Mimaki Tx2-1600 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Mimaki Tx2-1600 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Mimaki Tx2-1600 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Mimaki Tx2-1600 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Mimaki Tx2-1600 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Mimaki Tx2-1600 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Mimaki Tx2-1600 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.