Gebruiksaanwijzing /service van het product MX-100 van de fabrikant MK Sound
Ga naar pagina of 16
Miller & Kreisel Sound Corporation 10391 Jefferson Boulevard Culver City, CA 90232 USA (310) 204-2854 FAX (310) 202-8782 © 1994 MILLER & KREISEL SOUND CORP.
page 2 powered subwoofers T ABLE OF CONTENTS 1. SAFETY INSTRUCTIONS.............................................................................3 2. INTRODUCTION..........................................................................................
pa ge 3 powered subwoofers 1. SAFETY INSTRUCTIONS 1. READ INSTRUCTIONS - All safety and operating instructions should be read before this product is operated. 2. RETAIN INSTRUCTIONS - The safety and operating instructions should be retained for future reference.
page 4 powered subwoofers 2. INTRODUCTION Congratulations! You have just made perhaps the most exciting and dramatic addition that you could make to your audio or audio/video system. The new dimension of deep and powerful bass provided by your M&K Subwoofer will thrill and excite you.
pa ge 5 powered subwoofers Look at the back panel of the Subwoofer. You will see two RCA input jacks labelled "FROM PREAMP," and two sets of speaker wire input terminals labelled "FROM AMPLIFIER" and "TO SPEAKERS." You must choose to use either the speaker wire inputs or the RCA jack inputs .
page 6 powered subwoofers You now have two options for connecting your Satellite speakers. SA TELLITE SPEAKER WIRING OPTION 1 With this option, you connect the wiring for the Satellites directly to the Subwoofer. There is no performance advantage with this method, but it may require less speaker wire and be more convenient.
pa ge 7 powered subwoofers FIGURE 2 - SA TELLITE SPEAKER WIRING OPTION 1 (ALSO SHOWS USE OF THE V-125's HIGH-LEVEL HIGH-PASS FILTER) If your Amplifier has two sets of speaker outputs (e.g., A and B), you can connect the Satellites to one set and the Subwoofer to the other.
page 8 powered subwoofers Unless you have a V-125, a full-range signal (including deep bass) is fed to your Satellites. To roll off (filter) the signal fed to the Satellite speakers to achieve true biamplification, you must: 1. Have a separate amp and preamp OR a receiver or integrated amp that allows you to separate its amp and preamp stages.
pa ge 9 powered subwoofers the left Subwoofer and the right interconnect cable to the right Subwoofer. WIRING WITH THE LP-1S & VF-100 ELECTRONIC HIGH-P ASS FIL TERS The M&K LP-1S and VF-100 El.
page 10 powered subwoofers PLUGGING IN THE SUBWOOFER Once all the speaker wires or preamp interconnect cables are in place, you are ready to plug in the Subwoofer. Set the "BASS LEVEL" control to "MIN". Then plug the AC cord in. You should hear a thump from the Subwoofer.
pa ge 11 powered subwoofers Now listen to the same musical passage as you did earlier, concentrating on the mid-bass region. If you hear less bass, the original connections were correct. If you hear more bass, the new connections are correct. If you have two Subwoofers, perform one test for each Subwoofer.
page 12 powered subwoofers the "BASS LEVEL" control slightly higher. 8. FINE-TUNING SUBWOOFER PLACEMENT If you have the physical space in your room and the interest to experiment with the placement of your Subwoofer, you may be able to optimize its location and sound.
pa ge 13 powered subwoofers In some cases, however, you may prefer the subwoofer set to a higher playback level for video sources. This may occur when video sources (especially older films and some television) have very little deep bass present.
page 14 powered subwoofers . producing a "boomy" sound if it is located in a corner. Always try the subwoofer first in a corner. If it sounds "boomy," move it a few feet out of the corner.
pa ge 15 powered subwoofers c. Check the red LED on the Subwoofer's back panel. If the LED is not lit, check the AC fuse next to the LED. Unplug the Subwoofer before changing the fuse. See instructions on Page 15. If the element inside the fuse is broken, replace the fuse.
page 16 powered subwoofers probably coming from another component. Hum can also be caused by AC ground loops. If the Subwoofer is plugged into a separate AC outlet, try plugging it into the same outlet used for your amplifier or receiver, or reverse the polarity of its AC plug.
Een belangrijk punt na aankoop van elk apparaat MK Sound MX-100 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen MK Sound MX-100 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens MK Sound MX-100 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding MK Sound MX-100 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over MK Sound MX-100 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van MK Sound MX-100 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de MK Sound MX-100 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met MK Sound MX-100 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
