Gebruiksaanwijzing /service van het product M-DH van de fabrikant Moyer Diebel
Ga naar pagina of 33
Technical Manual Hood Type Dishwasher Model: M-DH High Temperature with Built-in Booster April, 2003 Manual P/N 113512 Rev A Machine Serial No. www .championindustries.
Complete the information below so it will be available for quick reference. Model Number Serial Number Voltage and Phase Moyer Diebel Service Agency Phone Moyer Diebel Parts Source Phone Moyer Diebel Service Moyer Diebel (USA) Phone: 1 (336) 661-1992 1 (800) 858-4477 Fax: 1 (336) 661-1660 E-mail www.
i Revision History Revision Revised Serial Number Comments Date Pages Effectivity 09/01/01 — First issue of manual and replacement parts 06/10/02 3 Inserted electrical wiring diagrams.
ii REVISION RECORD.
iii T ABLE OF CONTENTS CONTENTS Page REVISION HISTORY ............................................................................................................... ..... i GENERAL .....................................................................
iv THIS PAGE INTENTIONALLY LEFT BLANK.
1 GENERAL SPECIFICA TION GENERAL SPECIFICATIONS About this manual All information, illustrations and specifications contained in this manual are based upon the latest product information available at the time of publication.
2 ! ! INST ALLA TION Figure 1 Remove Front Panel INSTALLATION Unpack the dishwasher CAUTION: Care should be taken when lifting the machine to prevent damage. NOTE: The installation of your machine must meet all applicable health and safety codes. 1. Immediately after unpacking the machine, inspect for any shipping damage.
3 INST ALLA TION { L1 L2 L3 208/240V N Ground Earth Ground Connect (1) Hot wire to either L1, L2 or L3 Connect the second Hot wire to "N" terminal SINGLE PHASE CONNECTION L1 L2 L3 N Ground E.
4 ! INST ALLA TION INSTALLATION (CONT.) Plumbing Connections NOTE: Plumbing connections must comply with all applicable sanitary and plumbing codes. W ater Connections 1. All M-DH dishwashers require a single, hot water supply. 2. The hot water connection to the dishwasher is 1/2” BSP male.
5 INSTALLATION (CONT.) Chemical Connections NOTE: Consult a qualified chemical supplier for your chemical needs. 1. A chemical signal terminal block is supplied for chemical dispensing equipment. 2. The terminal block is located below the control panel fuse block.
6 OPERA TION INITIAL START-UP Complete the installation After the plumbing and electrical connections are made, follow the steps below to complete the installation of your dishwasher. 1. Remove the protective covering from the exterior of the machine.
7 DAILY CLEANING 1. Turn dishwasher and wall switch OFF. 2. Remove the overflow to drain wash tank. 3. Remove scrap screens and wash pump inlet screen.
8 MAINTENANCE MAINTENANCE Before carrying out the cleaning and the maintenance operations, turn off the main disconnect switch for the equipment. Do not use corrosive products such as sodium hypochlorite (bleach), acids, steel wool or steel brushes to clean the inside and the outside of machine.
9 TROUBLESHOOTING TROUBLESHOOTING In order to find the cause of a breakdown or abnormal operating condition in your dishwasher please ensure that: 1. All switches are ON 2. Drain and overflow tube are in place and seated 3. Wash pipe and rinse nozzles are clean 4.
10 CONDITION CAUSE SOLUTION Insufficient pumped spray Clogged pump intake screen ............ Clean pressure Clogged spray pipe .......................... Clean Scrap screen full ............................... Must be kept clean and in place Low water level in tank .
REPLACEMENT PARTS 11 REPLACEMENT PARTS.
REPLACEMENT PARTS 12 (DEMA HOLE PLUG) Note #1: Use Loctite 290 Note #2: Use thread tape Note #3: Use Loctite 243 Note #3 Note #3 Note #1 Note #2 ELEMENT LOCKNUTS ELEMENT GASKETS THERMOSTAT PROBE 14 15.
REPLACEMENT PARTS 13 WASH TANK ASSEMBLY Fig.3 Part Item No. No. Part Description Qty. 1 32590001 Hose Outlet .............................................................................................. 1 2 ASS24 Hose Clamp ..........................
REPLACEMENT PARTS 14 Figure 4 Wash and Rinse Arm Assemblies 15 4 14 5 5 1 2 6 7 8 9 11 12 13 10 9 3 8 7 2 5 1.
REPLACEMENT PARTS 15 WASH AND RINSE ARM ASSEMBLIES Fig.4 Part Item No. No. Part Description Qty. 1 40030037 Plug, Wash End ....................................................................................... 2 2 ARP018 O-ring, Wash Plug ...........
REPLACEMENT PARTS 16 Figure 5 Rinse Booster Assmbly and Rinse System 5 5 1 2 5 3 10 12 2 5 11 6 8 14 15 2 16 16 9 7 13 2 NOTE #1 BULKHEAD NUT & GASKET W ASH HUBS NO TE #2 FLOW DIRECTION NO TE #1. USE THREAD T APE ON CRO X AND THREADED FITTINGS T O SEAL JOINTS.
REPLACEMENT PARTS 17 RINSE BOOSTER ASSEMBLY AND RINSE SYSTEM Fig.5 Part Item No. No. Part Description Qty. 1 40010061 Rinse Booster Assy (Includes Item 26) ................................................... 1 2 60090028 H ose Clamp ..................
REPLACEMENT PARTS 18 Screw assignment diagram 1 2 4 7 3 6 5 9 8 20 10 11 18 12 13 15 19 14 17 17 17 17 16 16 Figure6 Control Cabinet.
REPLACEMENT PARTS 19 CONTROL CABINET Fig.6 Part Item No. No. Part Description Qty. 1 32275 Terminal S trip 6 Way .............................................................................. 1 2 60030089 Bushing Snap-In 25mm .........................
REPLACEMENT PARTS 20 Figure 7 Control Panel 11 10 3 4 6 7 5 12 1 2 8 9 NO TE: 1 SECURE GA UGES USING U CLAMP AND LOCKNUT SUPPLIED 12.
REPLACEMENT PARTS 21 CONTROL PANEL Fig.7 Part Item No. No. Part Description Qty. 1 40020060 Con trol Cabinet Panel ............................................................................. 1 2 30411 4 Position Switch ..............................
REPLACEMENT PARTS 22 THIS PAGE INTENTIONALLY LEFT BLANK.
23 ELECTRICAL SCHEMATICS ELECTRICAL SCHEMATICS.
For a more detailed explaination of wiring connections, see page 3 Fig. 2 of Installation section in manual M-DH ELECTRIC 080221 REV D A TE C 7/29/02.
For a more detailed explaination of wiring connections, see page 3 Fig. 2 of Installation section in manual M-DH ELECTRIC 080223 REV D A TE C 7/29/02.
F or a more detailed e xplaination of wiring connections see page 3 Fig. 2 of Installation section of manual. M-DH ELECTRIC 080133 REV D A TE D 7/29/02.
F or a more detailed e xplaination of wiring connections see page 3 Fig. 2 of Installation section of manual. M-DH ELECTRIC 080134 REV D A TE E 7/29/02.
Een belangrijk punt na aankoop van elk apparaat Moyer Diebel M-DH (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Moyer Diebel M-DH heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Moyer Diebel M-DH vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Moyer Diebel M-DH leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Moyer Diebel M-DH krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Moyer Diebel M-DH bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Moyer Diebel M-DH kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Moyer Diebel M-DH . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.