Gebruiksaanwijzing /service van het product TCS Twin van de fabrikant Art
Ga naar pagina of 20
ART TCS Twin Compressor System IMPORTANT SAFETY INSTRUCTION – READ FIRST This symbol, whenever it appears, This symbol, wherever it appears, alerts alerts you to the presence of uninsulated you to important operating and maintenance dangerous voltage inside the encl osure-voltage instructions in the accompanying literature.
ART TCS Twin Compressor System The ART TCS Twin Compressor System Table of Contents Introduction ........................................................................................... 4 TCS Features ...........................................
ART TCS Twin Compressor System INTRODUCTION Thank you and congratulations on your purchase of an ART TCS (Twin Compressor System). You now own a unique compression system with features unlike any other.
ART TCS Twin Compressor System TCS FEATURES Optical Compression VCA Compression 4 Compression Modes /16 Different V3 settings Controls Per Channel Attack and Release Transient Cont.
ART TCS Twin Compressor System INSTALLATION The TCS may be used in a wide variety of applications and environments. In a rack-mountable, all-steel enclosure, the unit is designed for continuous professional use.
ART TCS Twin Compressor System CONTROLS & INDICATORS 1 Power – Switches the unit’s power on and off. 2 Instrument Input and Level – The front ¼” jack is intended for instrument level signals and the level control applies from 0 to 30db of gain to the signal.
ART TCS Twin Compressor System 5 Bypass, Tube, Det.Loop Switches – These 3 switches control the channel settings. When depressed, the BYPASS switch completely bypasse s the compressor controls, including output level (It should be noted that this is an active bypass, so if the unit is unpowered no signal shall pass through).
ART TCS Twin Compressor System REAR CONNECTIONS 1 Rear Input Jacks – The TCS features both ¼ inch and XLR connectors on the back as inputs wired in parallel. The rear input jacks accept line level signals up to +20dBu. The rear inputs of Channel 1 ar e disconnected whenever the front panel ¼” jack is used.
ART TCS Twin Compressor System OPERATION Compression Basics – Compression is an effectiv e way to gently control the dynamics of a signal. The most important setting in your compressor is the threshold . The threshold sets the average signal level, above which the TCS acts on.
ART TCS Twin Compressor System might be necessary. If a VCA comp ressor has one advantage over opto- based compression, it’s speed. VCAs have very quick response time when peaks need to be compressed very rapi dly. For these reasons VCAs are especially good in situations that require amplitude protection.
ART TCS Twin Compressor System Manual – this is a general all-purpose setting, which gives you maximum flexibility; it uses a gate for noise reduction. Percussion – this setting is intended for percussion compression on single instruments such as snare, kick, etc, and includes a gate for noise reduction.
ART TCS Twin Compressor System V3 Quick Reference Chart NAME MODE NOISE REDUCTION SPEED RANGE NOTES NICE STACK GATE Normal GUITAR STACK EXPANDER Fast BASS OPTO EXPANDER Normal MIX OPTO EXPANDER Normal.
ART TCS Twin Compressor System COMMON APPL ICATION S Setting up the TCS with a mixing console For most compression situations we want to set the TCS in series with the channels it will be processing. Start by first placing an insert cable (¼ inch TRS to 2 ¼ inch TS) into the channel(s) insert point on your console.
ART TCS Twin Compressor System Ducking One example of utilizing the detector loop inserts on your TCS is ducking. With the TCS connected to the source material to be compressed place a line level signal, such as a vocal mic r un through a pre amplifier, into the side chain jack on the TCS.
ART TCS Twin Compressor System ADDITIONAL APPLICATIONS Setting up the TCS for sustain with a guitar amplifier If your guitar amp has a pre-EQ effects loop you can patch the TCS into it. Otherwise plug your guitar into the instrument input on Channel 1 of the TCS, and increase the instrument level until you’re working with a decent signal level.
ART TCS Twin Compressor System Setting up the TCS for stereo mastering For bus mastering or stereo mix masteri ng try placing the TCS in the signal chain after the mixer, or on a subgroup bus.
ART TCS Twin Compressor System WARRANTY INFORMATION Limited Warranty Applied Research and Technology will pr ovide warranty and service for this unit in accordance with the following warrants: Applied.
ART TCS Twin Compressor System SERVICE The following information is provided in the unlikely event that your unit requires service. 1) Be sure that the unit is the cause of the problem. Check to make sure the unit has the proper power supplied, all cables are connected correctly, and the cables themselves ar e in working condition.
ART TCS Twin Compressor System TCS™ SPECIFICATIONS Dimensions 1.75”H x 19”W x 7.5”D Weight 7.0 lbs. Analog Input Connections Fron t: ¼ inch instrument (unbal) Rear: XLR, ¼ inch TRS (balanced.
ART TCS Twin Compressor System - 21 - Applied Research & Technology 215 Tremont Street Rochester, NY 14608 USA (585) 436-2720 (Tel) (585) 436-3942 (Fax) cserve@artproaudio.
Een belangrijk punt na aankoop van elk apparaat Art TCS Twin (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Art TCS Twin heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Art TCS Twin vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Art TCS Twin leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Art TCS Twin krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Art TCS Twin bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Art TCS Twin kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Art TCS Twin . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
