Gebruiksaanwijzing /service van het product TubeFire 8 van de fabrikant Art
Ga naar pagina of 26
TubeFire 8 ™ 8 CHANNEL TUBE MIC-PREAMP SYSTEM USER’S GUIDE.
IMPORTANT SAFETY INSTRUCTIONS – READ FIRST This symbol, wherever it appears, This symbol, wherever it appears, alerts alerts you to the presence of uninsulated you to important operating and maintenance dangerous voltage inside the enclosure. Voltage in structions in the accompanying literature.
The ART TubeFire 8 8 Channel Tube Mic-Pre System IMPORTANT SAFETY INSTRUC TIONS – READ FIRST ............................................... 1 INTRODUC TION.........................................................................................
List of Figures FIGURE 1 - In put Chan nel ....................................................................................................... .................................................................. 5 FIGURE 2 - Output Mi x/Headphone section.
INTRODUCTION The TubeFire 8™ is the answer to your recording and computer interface needs. Eight high quality vacuum tube microphone preamps are packaged in a single rack high package. Our second generation discrete class– A mic preamps provide clean quiet gain while mainta ining incredible transparency.
Firewire (IEEE 1394) (Sony iLINK ® ) Connections The TubeFire 8 has two 6 pin Firewire ports located on the rear panel. Both ports are identical, and can be used interchangeably. Use a quality Firewire cable to connect the TubeFire 8 to your computer.
Instrument Input The 1/4” TS jack on the front p anel provides a high impedance unbalanced input, and when used, automatically switches off the mic pre-amp. (The r ear combo jack’s 1/4” TRS balanced input is lower impedance and is part of the mic pre-amp.
FIGURE 2 - Output Mix/Headphone section Headphone / Line Mixer All of the sources selected for the o utput jacks of t he TubeFire 8™ are mixed together to provide a signal for the Headphone/Line Mixer Output.
REAR PANEL Balanced Input Jacks – XLR & 1/4” TRS Combo Jacks These balanced inputs are used for both microphone and line level signa ls. The gain sensitivity is identical for both the XLR and 1/4” TRS jacks, however the XLR input impedance is 6.
HARDWARE OPERATION How to adjust the controls for the lowest noise Start with the GAIN and OUTPUT knobs centered, and the Pad switch IN. This provides about 20dB of gain. Increase the Gain control until the Clip LED in the meter just barely comes on during the loudest peaks in level, and then back off the control slightly from that point.
FIGURE 4 - Block Diagram 10.
PC SOFTWARE OPERATION Installing the Windows PC driver (Check at www.artproaudio.com for any driver updates.) Run SETUP.EXE on the driver disk to install the ART Firewire Driver. The installer will prompt for the destination directory. We suggest using the defaults.
Changing the sample rate STEP ONE: Open the ART Card Control panel on a PC, to modify the sample rate setting. FIGURE 6 - Control Panel Sample Rate STEP TWO: Change the sample rate setting in the recording software. In Cubase, this is done under the PROJECT tab in the PROJECT SETUP dialog.
Changing the sample rate may lead to other issues, including audio dropouts. Monitor the ASIO Drop Outs for 10 - 20 seconds to assure that the number remains at zero. If they are NOT zero, then increase the buffe r length until the ASIO Drop Outs number reduces to zero.
Adjusting system latency with a Windows PC Adjusting the buffer depth varies the latency of the computer system used together with the TubeFire 8™. Typical recording software programs utilize either WDM or ASIO drivers. Adjusting the buffer depth control to the left will reduce the buffer size and therefore reduce the latency.
Using the wordclock input with a Windows PC The TubeFire 8™ can be used in both simple and complex systems. The simplest system would consist of the TubeFire 8™ and a computer. As multiple digital devic es are added to a system, master/slave sample rate timing issues degrade audio performance.
Mac SOFTWARE OPERATION Changing the sample rate with a Mac Run the AUDIO/MIDI setup utility to change the sample rate. Select properties for the device labeled “ART Firewire nnnn” (the “nnnn” refers to a unique serial number for each TubeFire 8™).
Using the wordclock input with a Mac The TubeFire 8™ can be used in both simple and complex systems. The simplest system would consist of the TubeFire 8™ and a computer. As multiple digital devic es are added to a system, master/slave sample rate timing issues degrade audio performance.
Creating an Aggregate Device with a Mac Control of multiple audio devices on a Mac is performed by creating a single Aggregate Device. What follows is an example combining two TubeFire 8™ units into a single Aggregate Device, but it could be two completely different digital audio products.
APPLIC ATIONS Adding more TubeFire 8™ units to your system The TubeFire 8™ is designed to allow you to expand the number of inputs and outputs on your system by adding more TubeFire 8™ units. The bandwidth of the Firewire buss limits the nu mber of units that can be added to a system.
Optionally rename the units in the ART Card Control Panel (Windows PC) or create an “Aggregate Device” (Mac) to simplify the ID of each unit. See the Mac Software Operation section for instructions on creating an Aggregate Device. Note that the order of devices listed is arranged by each unit’s SERIAL NUMBER.
WARRANTY INFORMATION Limited Warranty: Applied Research and Technology will provide warr anty and service for this unit in acco rdance with the following warrants: Applied Research and Technology, (A .
SERVICE The following information is provided in the unlik ely event that your unit requires service. 1) Be sure that the unit is the cause of the problem. Check to ma ke sure the unit has the proper power supplied, all cables are connected correct ly, and the cables themselves are in working condition.
TubeFire 8™ SPECIFICATIONS Input Impedance Mic .............................................................................................. 6. 4K Ohm Line ............................................................................................
NOTES 24.
www.artproaudio.com E-mail: support@artproaudio.com © 2006 Applied Research & Technology 164-5004-201 25.
Een belangrijk punt na aankoop van elk apparaat Art TubeFire 8 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Art TubeFire 8 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Art TubeFire 8 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Art TubeFire 8 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Art TubeFire 8 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Art TubeFire 8 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Art TubeFire 8 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Art TubeFire 8 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
