Gebruiksaanwijzing /service van het product 6FE van de fabrikant MTD
Ga naar pagina of 28
Two-Stage Snow Thrower Styles E & F Oper ator’ s Man ual Model 6FE Shown IMPOR T ANT : READ SAFETY R ULE S AND INSTR UCTIONS CAREFULL Y Warning: This unit is equipped with an internal co mbustio.
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Ma nual is an important part of yo ur new snow thrower. It w ill help you assemb le, prepare and maintain the unit fo r best performance.
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: Engine Exhaust, some of it s constituents , and cer tain vehicle components contain or emit chemicals known to the State of Calif or nia to cause cancer , birth defects or other reproductiv e harm .
4 Operation 1. Do not put hands or feet near rotating p arts, in the auger/impeller housing or chute assembly. Contact with the rotating parts can amputate hand s and feet. 2. The aug er/impeller contr ol lever is a safety device. Never bypa ss its opera tion.
5 YOUR RESPONSIBILITY Restrict the use of this power machine to persons who read, understand and follow the warnings and in structions in this manual and on the machine. Do not modify engine To avoid serious injury or de ath, do not modify engine in any way.
6 SECTION 2: ASSEMBLING YOUR SNOW THROWER NOTE: References to rig ht or left side of the snow thrower are de termined from behind th e unit in the operating p osition (stand ing directly be hind the snow thrower, facing th e handle panel). NOTE: This Operator’s Manu al covers several models.
7 Attaching the Chute Assembly and Directional Control 1. Apply a light lubricant (i.e. 3-in- 1 oil) to the rim of the chute base and position t he chute assembly over the base. 2. Close the flange keepe rs to secure the chute assembly to the chut e base.
8 SECTION 3: KNOW YOUR SNOW THROWER WARNING: Read, understa nd, and follow all instructions and wa rnings on the machine and in this manual before operating.
9 Auger Control The auger cont rol is located on the left handle. Squeeze the co ntrol grip against the handle to en gage the augers and start sno w throwing action. Release to stop. Drive Contro l The drive control is located on the right hand le. Squeeze the co ntrol grip against the handle to en gage the wheel drive.
10 SECTION 4: OPERATING YOUR SNOW THROWER Before Starting WARNING: Read, understand, and follow all instructions and wa rnings on the machine and in this manual befor e operating. Gas & Oil Fill-Up Service the eng ine with gasoline and oil a s instructed in the Tecumseh Engines ma nual packed separately with your snow thrower.
11 • Pull the starter handle with a firm, rapid stroke. IMPORT ANT: Do not releas e the ha ndle and allow it to snap back. Keep a firm hold on the star ter handle and allow it to slowly recoil. • As the engine warms, slowly rotate the choke control to t he OFF posit ion.
12 • To readjust th e control cable, loosen the hex jam nut on the auger cont rol cable “Z” fitting. • Rotate the coup ling end of the cable counterclockwise to provide more slack. • Retighten the he x jam nut. See Figure 1. • Repeat Auger Con trol Test to verify proper adjustment has been achieved.
13 SECTION 5: MAKING ADJUSTMENTS WARNING: Never at tempt to mak e any adjustments wh ile the engine is running, except where sp ecified in operator’s ma nual. Shift Rod Adjustment If the full range of speed s (forward and reverse) cannot be achiev ed, refer to the figur es to the r ight and adjust the shift rod as follow s: 1.
14 Drive Contro l When the drive control is released a nd in the disengaged “u p” position, the cable should have very little slack. It sh ould NOT be tight. Check the adjustment of th e drive control as follows: 1. With the drive control released , push the snow thrower gently forward .
15 SECTION 6: MAINTAINING AND SERVICING YOUR SNOW THROWER WARNING: Before lubricating, repairing, or inspecting, disengag e all controls and stop engine. Wait until all moving parts have come to a complete stop. Engine Refer to the sepa rate Tecumseh Engines manual packed with your unit fo r all engine maintenance .
16 Auger Belt Replacement To remove a nd replace your snow t hrower’s auger b elt, proceed as follows: 1. Remove the plastic belt cove r on the front of the engine by removing the two self-t apping screws. • Drain the ga soline from the snow thro wer, or place a piece of plastic under the gas cap.
17 Drive Belt Replacement To remove a nd replace your snow t hrower’s auger b elt, proceed as follows: 1. Remove the plastic belt cove r on the front of the engine by removing the two self-t apping screws. • Drain the ga soline from the snow thro wer, or place a piece of plastic under the gas cap.
18 Friction Wheel Removal If the snow throwe r fails to drive with the driv e control engaged, and pe rforming the drive control cable adjustment on page 14 f ails to correct the problem, th e friction wheel may need to be r eplaced. Follow the instructions below.
19 Augers • The augers a re secured to the spiral shaft with two shear pins and cotter pins. If the auger should st rike a foreign object or ice ja m, the snow thro wer is designed so that the pins may sh ear. Refer to F igure 8. • If the augers will no t turn, check to see if the pins have sheare d.
20 SECTION 8: TROUBLE SHOOTING GUIDE NOTE: For repairs beyond t he minor adju stments abov e, contact y our local au thorized se rvice dealer. T roub le P ossible Cause (s) Corrective Action Engine fails to start Fuel t ank empty, or stale fuel. Blocked fuel line.
21 NOTES.
22 SECTION 9: PARTS LIST 4 20 3 38 28 6 50 17 13 8 1 2 20 14 10 39 36 32 31 33 27 26 8 30 35 37 3 7 11 25 8 19 15 7 9 5 22 24 23 16 12 7 18 34 9 43 42 41 40 21 47 45 29 48 49 44 46.
23 Styles E & F REF . NO . PA R T NO . DESCRIPTION 1 684-04106 Handle Ass’y , Engageme nt RH Black 2 684-04105 Handle Ass’y , Engagement, LH Black 3 710-0726 Screw , Self-tapping , 5/16-12, 0.750 4 710-1233 Screw , Machine, #10-24, 1.375 5 711-0677 F errule, 5/16-18 x .
24 27 27 50 46 49 52 59 56 60 33 29 33 28 28 51 45 30* 31 34 32 53 57 48 55 2 7 35 4 4 8 44 8 6 21 23 12 7 14 18 61 15 24 3 22 9 38 40 4 36 1 16 5 13 26 37 41 8 6 8 43 4 42 25 62 54 58 47 Styles E &am.
25 Sales E & F REF . NO . PA R T NO . DESCRIPTION 1 731-2643 Clean Out Tool 2 684-04057 Impeller Assembly, 12” Diameter 3 710-0347 Hex Screw, 3/8-16, 1.75, Gr5 , Std 4 710-0451 Bolt, Carriage, 5/16-18, .750 Gr1 5 710-0703 Screw, Carriage, 1/4-20, .
26 39 50 46 56 52 47 55 57 4 51 4 45 48 58 43 53 42 49 59 40 54 57 44 5 41 2 2 1 68 24 5 66 67 23 35 31 26 34 33 5 25 17 16 29 18 27 10 32 8 19 3 22 1 37 18 13 21 18 62 15 14 9 11 12 11 28 5 30 25 5 3.
27 REF . NO . PA R T NO . DESCRIPTION 1 656-0012A Disc Assemb ly, Wheel, .375 Friction 2 684-04066 Friction Wheel Ass’y, Bearing, 4.9 OD 3 684-04045 Support Bracket Ass’y, Friction Whee l 4 710-0627 Hex Screw, 5/16-24, .750, Gr5 5 710-0896 Screw, Self-tapping, 1/4-14, 0.
MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its poss essions and territories.
Een belangrijk punt na aankoop van elk apparaat MTD 6FE (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen MTD 6FE heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens MTD 6FE vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding MTD 6FE leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over MTD 6FE krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van MTD 6FE bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de MTD 6FE kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met MTD 6FE . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
